This BUG_ON is unneeded since the ->handler != NULL check is performed in
ide_set_handler().
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace the ide-floppy packet commands opcode defines with the generic ones.
Add a missing GPCMD_WRITE_12 (opcode 0xaa) to the generic ones in cdrom.h. The
last one can be found in the current version of INF-8090, p.905.
[ Bart: Tejun's libata patch also adding GPCMD_WRITE_12 got merged first ]
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->cable_detect method to ide_hwif_t.
* Call the new method in ide_init_port() if:
- the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
- DMA initialization was successful (if hwif->dma_base is not set
ide_init_port() sets hwif->ultra_mask to zero)
- "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')
* Convert PCI host drivers to use ->cable_detect method.
While at it:
* Factor out cable detection to separate functions (if not already done).
* hpt366.c/it8213.c/slc90e66.c:
- don't check cable type if "idex=ata66" is used
* pdc202xx_new.c:
- add __devinit tag to pdcnew_cable_detect()
* pdc202xx_old.c:
- rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
- add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma().
* Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version.
* Add 'const struct ide_port_info *d' argument to ide_device_add[_all]().
* Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(),
move it to ide-probe.c and call it in in ide_device_add_all() instead of
ide_pci_setup_ports().
* Move ->mate setup to ide_device_add_all() from ide_port_init().
* Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable
->autotune currently.
* Setup hwif->chipset in ide_init_port() but iff pi->chipset is set
(to not override setup done by ide_hwif_configure()).
* Add ETRAX host handling to ide_device_add_all().
* cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n.
* pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks
setup to pmac_ide_setup_device().
* Add 'struct ide_port_info' instances to legacy host drivers, pass them to
ide_device_add() calls and then remove open-coded ports initialization.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Setup ->mate and ->channel in ide_pci_setup_ports() instead of
in ide_hwif_configure().
* Make 'port' parameter for ide_hwif_configure() 'unsigned int'.
* Separate PCI specific init from generic init in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always set DMA masks in ide_pci_setup_ports() to make sure that the valid
masks for a host are set.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays IDE core always provides drive ID and ide-disk always setups
drive->capacity64 so this quirk is no longer needed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't override the cable type if the "idex=ata66" parameter was used.
While at it:
* atiixp.c: factor out cable detection to atiixp_cable_detect() from
init_hwif_atiixp().
* cs5535.c: pass 'ide_hwif_t *hwif' instead of 'struct pci_dev *dev' to
cs5535_cable_detect().
* scc_pata.c: factor out cable detection to scc_cable_detect() from
init_hwif_scc() and remove incorrect comment.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The host driver must set hwif's ->no_io_32bit setting not drive's one
(ide_port_tune_devices() overrides drive's setting).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On DTC2278 32-bit I/O has to be enabled for both devices on the port
so always enable it during init time and disallow further changes.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
sg_dma_len(sg) is invalid before the s/g list is DMA-mapped.
This fixes a post 2.6.24 regression which prevents access to SBP-2
devices on several architectures, introduced by "ieee1394: sbp2: s/g
list access cosmetics", commit 825f1df545.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.infradead.org/battery-2.6:
apm_power: check I.intval for zero value, we use it as the divisor
MAINTAINERS: remove kernel-discuss@handhelds.org list
pda_power: implement polling
pda_power: various cleanups
apm_power: support using VOLTAGE_* properties for apm calculations
pda_power: add suspend/resume support
power_supply: add few more values and props
pda_power: only register available psu
power: fix incorrect unregistration in power_supply_create_attrs error path
power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
[BATTERY] power_supply_leds: use kasprintf
[BATTERY] Every file should include the headers containing the prototypes for its global functions.
* 'for-linus' of git://linux-nfs.org/~bfields/linux: (100 commits)
SUNRPC: RPC program information is stored in unsigned integers
SUNRPC: Move exported symbol definitions after function declaration part 2
NLM: tear down RPC clients in nlm_shutdown_hosts
SUNRPC: spin svc_rqst initialization to its own function
nfsd: more careful input validation in nfsctl write methods
lockd: minor log message fix
knfsd: don't bother mapping putrootfh enoent to eperm
rdma: makefile
rdma: ONCRPC RDMA protocol marshalling
rdma: SVCRDMA sendto
rdma: SVCRDMA recvfrom
rdma: SVCRDMA Core Transport Services
rdma: SVCRDMA Transport Module
rdma: SVCRMDA Header File
svc: Add svc_xprt_names service to replace svc_sock_names
knfsd: Support adding transports by writing portlist file
svc: Add svc API that queries for a transport instance
svc: Add /proc/sys/sunrpc/transport files
svc: Add transport hdr size for defer/revisit
svc: Move the xprt independent code to the svc_xprt.c file
...
* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
suspend: cleanup reference to swsusp_pg_dir[]
PM: Remove obsolete /sys/devices/.../power/state docs
Hibernation: Invoke suspend notifications after console switch
Suspend: Invoke suspend notifications after console switch
Suspend: Clean up suspend_64.c
Suspend: Add config option to disable the freezer if architecture wants that
ACPI: Print message before calling _PTS
ACPI hibernation: Call _PTS before suspending devices
Hibernation: Introduce begin() and end() callbacks
ACPI suspend: Call _PTS before suspending devices
ACPI: Separate disabling of GPEs from _PTS
ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
Suspend: Introduce begin() and end() callbacks
suspend: fix ia64 allmodconfig build
ACPI: clear GPE earily in resume to avoid warning
Suspend: Clean up Kconfig (V2)
Hibernation: Clean up Kconfig (V2)
Hibernation: Update messages
Suspend: Use common prefix in messages
Hibernation: Remove unnecessary variable declaration
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (128 commits)
USB: fix codingstyle issues in drivers/usb/core/*.c
USB: fix codingstyle issues in drivers/usb/core/message.c
USB: fix codingstyle issues in drivers/usb/core/hcd-pci.c
USB: fix codingstyle issues in drivers/usb/core/devio.c
USB: fix codingstyle issues in drivers/usb/core/devices.c
USB: fix codingstyle issues in drivers/usb/core/*.h
USB: fix codingstyle issues in include/linux/usb/
USB: fix codingstyle issues in include/linux/usb.h
USB: mark USB drivers as being GPL only
USB: use a real vendor and product id for root hubs
USB: mount options: fix usbfs
USB: Fix usb_serial_driver structure for Kobil cardreader driver.
usb: ehci should use u16 for isochronous intervals
usb: ehci, remove false clear-reset path
USB: Use menuconfig objects
usb: ohci-sm501 driver
usb: dma bounce buffer support
USB: last abuses of intfdata in close for usb-serial drivers
USB: kl5kusb105 don't flush to logically disconnected devices
USB: oti6858: cleanup
...
Rafael J. Wysocki reported weird, multi-seconds delays during
suspend/resume and bisected it back to:
commit 82a1fcb902
Author: Ingo Molnar <mingo@elte.hu>
Date: Fri Jan 25 21:08:02 2008 +0100
softlockup: automatically detect hung TASK_UNINTERRUPTIBLE tasks
fix it:
- restore the old wakeup mechanism
- fix break usage in do_each_thread() { } while_each_thread().
- fix the hotplug switch stmt, a fall-through case was broken.
Bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- handle spurious interrupts correctly;
- get rid of pda_power_supplies array, use two variables instead;
- factor out psy_changed() function, it will be used for polling.
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
It's pretty dummy, but useful for batteries for which we can only
get voltages.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Add LiMn (one of the most common for small non-rechargable batteries)
battery technology and voltage_min/_max properties support.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Currently pda-power adds both ac and usb power supply units.
This patch fixes it so that psu are added only if they are enabled.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
In power_supply_create_attrs(), we create static attributes as referenced
by power_supply_static_attrs[i]. After that, if we fail, we unregister
via power_supply_static_attrs[psy->properties[i]]. This is incorrect, as
psy->properties has absolutely no bearing on static attribs. This patch
fixes it to unregister the correct attrib.
Another line which was unnecessarily line wrapped is also unwrapped.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The CAPACITY_LEVEL stuff defines various levels of charge; however, what
is the difference between them? What differentiates between HIGH and NORMAL,
LOW and CRITICAL, etc?
As it appears that these are fairly arbitrary, we end up making such policy
decisions in the kernel (or in hardware). This is the sort of decision that
should be made in userspace, not in the kernel.
If the hardware does not support _CAPACITY and it cannot be easily calculated,
then perhaps the driver should register a custom CAPACITY_LEVEL attribute;
however, userspace should not become accustomed to looking for such a thing,
and we should certainly not encourage drivers to provide CAPACITY_LEVEL
stubs.
The following removes support for POWER_SUPPLY_PROP_CAPACITY_LEVEL. The
OLPC battery driver is the only driver making use of this, so it's
removed from there as well.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use kasprintf instead of kmalloc()-strcpy()-strcat().
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
swsusp_pg_dir[] is used for suspend, but not for hibernation.
clean-up the ifdefs which worked by accident, while implying the opposite.
Delete the __nosavedata, which also implied the opposite.
Some day we may optimize CONFIG_ACPI_SLEEP to build minimal kernels
for just hibernate or just suspend but not both,
but today isn't that day.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The /sys/devices/.../power/state files have been gone for a while
now, but I just noticed some documentation that still refers to
them. (Fortunately described as DEPRECATED and WILL REMOVE).
Time to remove that obsolete documentation too ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Following the recent change in the suspend code path, switch consoles before
calling PM notifiers during hibernation.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
In order to fix APM emulation it is necessary to enable apm-emulation
notifications for suspends triggered in various ways via the suspend
notifiers. However, this will cause the systems using APM emulation
to lock up between X being needed to switch away from the VT and X
already waiting for resume in the APM ioctl.
This patch moves the console switch (if enabled) before the suspend
notification (and after the resume notification) to avoid this issue.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
There's a freakishly long comment in suspend_64.c, shorten it.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes the freezer optional for suspend to allow the
system to work (or not work) like the original PMU suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Make acpi_sleep_prepare() static and cause it to print a message
specifying the ACPI system sleep state to be entered (helpful for
debugging the suspend/hibernation code).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI 1.0 specification wants us to put devices into low power
states after executing the _PTS global control method, while ACPI
2.0 and later want us to do that in the reverse order. The current
hibernation code follows ACPI 2.0 in that respect which may cause some
ACPI 1.0x systems to hang during hibernation (ref.
http://bugzilla.kernel.org/show_bug.cgi?id=9528).
Make the hibernation code execute _PTS before putting devices into
low power states (ie. in accordance with ACPI 1.0x) with the
possibility to override that using the 'acpi_new_pts_ordering' kernel
command line option.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce global hibernation callback .end() and rename global
hibernation callback .start() to .begin(), in analogy with the
recent modifications of the global suspend callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI 1.0 specification wants us to put devices into low power
states after executing the _PTS global control method, while ACPI
2.0 and later want us to do that in the reverse order. The current
suspend code follows ACPI 2.0 in that respect which causes some
ACPI 1.0x systems to hang during suspend (ref.
http://bugzilla.kernel.org/show_bug.cgi?id=9528).
Make the suspend code execute _PTS before putting devices into low
power states (ie. in accordance with ACPI 1.0x) and provide a command
line option to override the default if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The preparation to enter an ACPI system sleep state is now tied to
the disabling of GPEs, but the GPEs should not be disabled before
suspending devices. Since on ACPI 1.0x systems the _PTS global
control method should be executed before suspending devices, we
need to disable GPEs separately.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
The execution of ACPI global control methods _GTS and _BFS is
currently tied to the preparation to enter a sleep state and to the
leaving of the sleep state, respectively. However, these functions
are called before disabling the nonboot CPUs and after enabling
them, respectively (in fact, on ACPI 1.0x systems the first of them
ought to be called before suspending devices), while according to the
ACPI specification, _GTS is to be executed right prior to entering
the system sleep state and _BFS is to be executed right after the
platfor firmware has returned control to the OS on wake up.
Move the execution of _GTS and _BFS to the right places.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
kernel/power/main.c:488: error: ‘pm_test_attr’ undeclared here (not in a function)
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Wakeup GPE hasn't a handler. If system is waked up by such GPE like a
USB hotplug, I saw a lot of error reporting the GPE hasn't handler.
acpi_leave_sleep_state will clear the GPE but it's too late, we should
do it before interrupt is re-enabled.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This cleans up the suspend Kconfig and removes the need to
declare centrally which architectures support suspend. All
architectures that currently support suspend are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This cleans up the hibernation Kconfig and removes the need to
declare centrally which architectures support hibernation. All
architectures that currently support hibernation are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Make hibernation messages start with one common prefix "PM: " and use
the word "hibernation" in the messages as a synonym of "suspend to
disk".
Turn some KERN_INFO messages into debug ones.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Make suspend messages start with one common prefix "PM: ".
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Borislav Petkov
Bartlomiej Zolnierkiewicz
Stefan Richter
Linus Torvalds
Peter Zijlstra
Anton Vorontsov
Dmitry Baryshkov
Andres Salomon
Akinobu Mita
Adrian Bunk
Rafael J. Wysocki
David Brownell
Johannes Berg
Shaohua Li