sata_mv: Fix broken Marvell 7042 support.
The Marvell 7042 chip is more or less the same as the 6042 internally,
but sports a PCIe bus. Despite having identical SATA cores, the 7042
does differ from its PCI bus counterparts in placment and layout of
certain bus related registers.
This patch fixes sata_mv to distinguish between the PCI bus registers
of earlier chips, and the PCIe bus registers of the 7042.
Specifically, move the offsets and bit patterns for the
PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv,
as these values differ between the 6xxx and 7xxx series chips.
This fixes the driver to not access reserved PCI addresses,
and prevents the lockups reported in linux-2.6.24 with 7042 boards.
Also add a new PCI ID for the Highpoint 2300 7042-based board
that I'm using for testing this stuff here.
Tested with Marvell 6081 + 7042 chips, on x86 & x86_64.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Fri, 30 Nov 2007 14:34:11 +0200 (EET)
Meelis Roos <mroos@linux.ee> wrote:
> > Can you stick a stack trace in at that point ? That would help diagnose
> > it a great deal quicker.
>
> Finally done - found out hard way that BUG() is too bad and
> dump_st5ack() suits me better.
Thanks. This should fix the real cause, and also allow for port start to
fail politely with -ENODEV.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add more toshiba laptops to broken suspend list. This is from OSDL
bugzilla bug 7780.
tj: re-formatted patch and added description and SOB.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata: Add more TSST (Samsung/Toshiba) IDE drives with broken
cable detection validation bits.
signed-off-by: Peter Missel (peter.missel@onlinehome.de)
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Protocol and CDB allocation size field are important in determining
what went wrong with ATAPI commands. Report them on failure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several fixes for the AVR32 PATA driver:
* Updated to use new AVR32 SMC timing API. This removes the need for "magic"
constants in signal timing.
* Removed the ATA_FLAG_PIO_POLLING, the driver should use interrupts.
* Removed .port_disable and .irq_ack as these are no longer needed.
* Improved some comments.
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
dma_addr_t is 64bit wide on some architectures (for example 64bit MIPS),
so it's not a good idea to use it for 32bit wide addresses in descriptors.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The VIA veloicty driver needs the following to allow changing MTU when down.
The buffer size needs to be computed when device is brought up, not when
device is initialized. This also fixes a bug where the buffer size was
computed differently on change_mtu versus initial setting.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This kind of sucks, and prevents the Fedora installer from using the
device for network installs...
[root@efika phy]# iwconfig eth0
Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...
eth0 ESSID:off/any Nickname:""
NWID:0 Channel:0 Access Point: 00:00:BF:81:14:E0
Bit Rate:-1.08206e+06 kb/s Sensitivity=0/0
RTS thr:off Fragment thr:off
Encryption key:<too big>
Power Management:off
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This helps to allow the Fedora installer to use the built-in Ethernet on
the Efika for a network install.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The smc911x.h is a bit of a mess, not supporting any sort of generic
configuration. For the moment only ARCH_PXA and SH_MAGIC_PANEL_R2 have
suitable definitions, so we reflect this in the Kconfig also.
While there are other SH boards that will likely turn this on in the
2.6.25 time frame, it's not worth trying to stub around at the moment.
Fixes up the allmodconfig build, as noted by akpm.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't exit polling when we have not yet used our budget, this causes
the NAPI system to end up with a messed up poll list.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add workaround for issues FE+ (A0) transmit watermark.
This is copied verbatim from vendor driver sk98lin (10.22.4.3).
Don't have that chip version and no more information seems to be available.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using PCIE advanced error recovery stuff creates more user problems than it's worth.
The AER stuff depends on MMCONFIG and in many configurations it just doesn't work.
Plus it doesn't add any real functionality to the driver. The sky2
driver handles its own errors fine as is.
This reverts 555382cbfc
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using the hardware window into PCI config space is more reliable
and smaller/faster than using the pci_config routines. It avoids issues
with MMCONFIG etc.
Reverts: 167f53d05f
Please apply for 2.6.24
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
netif_rx_complete() should be called only
when work_done < budget.
Signed-off-by: Divy Le ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch ensures that a GSO skb has enough headroom
to push an encapsulating cpl_tx_pkt_lso header.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Extend the RGMII-Internal Delay specification case to include
TX-only and RX-only variants.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Previously, Internal Delay specification implied the delay be
applied to both TX and RX. This patch allows for separate TX/RX-only
internal delay specification.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow phylib specification of cases where hardware needs to configure
PHYs for Internal Delay only on either RX or TX (not both).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code to change MTU doesn't correctly handle all the chip variations
and requirements for restarting. On Genesis chips changing MTU would just
cause receiver to hang.
Use a simpler approach of just taking link down/up if needed.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For compatiablity with sk98lin, make sure and set same values
in serial mode register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to increase TX threshold when doing Jumbo frames on dual port board
to avoid underruns. (Code from sk98lin).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver would not work over fibre if other end when down then
came back up (would require reloading driver). The correct way
to manage the link the same way for both TP and fibre.
Resloves problem described in: http://lkml.org/lkml/2007/11/6/395
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure and retry when shutting down the MAC. This code is copied
from sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Receive FIFO overrun is not catastrophic condition, so don't flush when
it happens.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The calculation of usable FIFO RAM is wrong in the skge driver.
First, is doesn't take into account the reserved area on the original
SysKonnect Genesis boards. Second it has an off-by-one error because
hw->ports is either 1 or 2.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently ctc-device initialization is broken (kernel bug in
ctc_new_device).
The new network namespace code reveals a deficiency of the
ctc driver. It should make use of alloc_netdev() as described
in Documentation/networking/netdevices.txt.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the case when the card initialization fails on a mtu change and then
close is called (due to ifdown), which frees non existent rx buffers.
- Returning appropriate error codes in init_nic function.
- In s2io_close function s2io_card_down is called only when device is up.
- In s2io_change_mtu function return value of s2io_card_up function
is checked and returned if it failed.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use smp_send_stop() to move all cpus besides the one executing reboot
into a hold loop, to keep them from being in powersavings mode at the
time of reboot.
Signed-off-by: Olof Johansson <olof@lixom.net>
When the PWRficient cpus are entered into powersavings states, the
astate is automatically dropped down to 0. While we still restore it
when we come out of idle, it can still cause some weird effects with
respect to performance (especially since it takes a while to ramp up to
higher astates).
So, to avoid this, don't enter power savings when the cpufreq driver
(or user) has set higher astates than 0.
The restore is still required, since there's a chance the astate has
been raised from the other cpu while the idling one was asleep.
Signed-off-by: Olof Johansson <olof@lixom.net>
Well I clearly goofed when I added the initial network namespace support
for /proc/net. Currently things work but there are odd details visible to
user space, even when we have a single network namespace.
Since we do not cache proc_dir_entry dentries at the moment we can just
modify ->lookup to return a different directory inode depending on the
network namespace of the process looking at /proc/net, replacing the
current technique of using a magic and fragile follow_link method.
To accomplish that this patch:
- introduces a shadow_proc method to allow different dentries to
be returned from proc_lookup.
- Removes the old /proc/net follow_link magic
- Fixes a weakness in our not caching of proc generic dentries.
As shadow_proc uses a task struct to decided which dentry to return we can
go back later and fix the proc generic caching without modifying any code
that uses the shadow_proc method.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Fix static rate if path faster than link
IPoIB: Fix oops if xmit is called when priv->broadcast is NULL
Freeing prom memory: 956kb freed
Freeing firmware memory: 978944k freed
Freeing unused kernel memory: 180k freed
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/1
caller is r4k_dma_cache_wback_inv+0x144/0x2a0
Call Trace:
[<80117af8>] r4k_dma_cache_wback_inv+0x144/0x2a0
[<802e4b84>] debug_smp_processor_id+0xd4/0xf0
[<802e4b7c>] debug_smp_processor_id+0xcc/0xf0
...
CONFIG_DEBUG_PREEMPT is enabled.
--
Bug cause is blast_dcache_range() in preemptible code [in
r4k_dma_cache_wback_inv()].
blast_dcache_range() is constructed via __BUILD_BLAST_CACHE_RANGE that
uses cpu_dcache_line_size(). It uses current_cpu_data that use
smp_processor_id() in turn. In case of CONFIG_DEBUG_PREEMPT
smp_processor_id emits BUG if we are executing with preemption
enabled.
Cpu options of cpu0 are assumed to be the superset of all processors.
Can I make the same assumptions for cache line size and fix this
issue the following way:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The formula would yield -1 if the path is faster than the link, which
is wrong in a bad way (max throttling). Clamp to 0, which is the
correct value.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4680/1: parentheses around NR_IRQS definition
[ARM] 4679/1: AT91: Change maintainer email address
[ARM] 4675/1: pxa: fix mfp address definition error for pxa320
[ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
[ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
[ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
[ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
[ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
[ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
[ARM] uengine: fix memset size error
[ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
[ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
[ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
[ARM] 4604/2: AT91: Master clock divistor on SAM9
[ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
[ARM] PXA ssp: unlock when ssp tries to close an invalid port
[ARM] 4654/1: pxa: update default MFP register value
[ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
[ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
[ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions
The database performance group have found that half the cycles spent
in kmem_cache_free are spent in this one call to BUG_ON. Moving it
into the CONFIG_SLAB_DEBUG-only function cache_free_debugcheck() is a
performance win of almost 0.5% on their particular benchmark.
The call was added as part of commit ddc2e812d5
with the comment that "overhead should be minimal". It may have been
minimal at the time, but it isn't now.
[ Quoth Pekka Enberg: "I don't think the BUG_ON per se caused the
performance regression but rather the virt_to_head_page() changes to
virt_to_cache() that were added later." ]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Pekka J Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a zero length pattern is passed then return EINVAL.
Avoids infinite loops (bm) or invalid memory accesses (kmp).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
When xt_CONNMARK is used outside the mangle table and the user specified
"--restore-mark", the connmark_tg_check() function will (correctly)
error out, but (incorrectly) forgets to release the L3 conntrack module.
Same for xt_CONNSECMARK.
Fix is to move the call to acquire the L3 module after the basic
constraint checks.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As far as I see from the err variable initialization
the dn_nl_deladdr() routine was designed to report errors
like "EADDRNOTAVAIL" and probaby "ENODEV".
But the code sets this err to 0 after the first nlmsg_parse
and goes on, returning this 0 in any case.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Avaid provided test application, so bug got fixed.
IPv6 addrconf removes ipv6 inner device from netdev each time cmu
changes and new value is less than IPV6_MIN_MTU (1280 bytes).
When mtu is changed and new value is greater than IPV6_MIN_MTU,
it does not add ipv6 addresses and inner device bac.
This patch fixes that.
Tested with Avaid's application, which works ok now.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Mark Lord
Alan Cox
Peter Schwenke
Peter Missel
Tejun Heo
Kristoffer Nyborg Gregertsen
Saeed Bishara
sonic zhang
Thomas Bogendoerfer
Stephen Hemminger
David Woodhouse
Paul Mundt
Auke Kok
Divy Le Ray
Kim Phillips
Peter Tiedemann
Sreenivasa Honnur
Jeff Garzik
Olof Johansson
Eric W. Biederman
Linus Torvalds
Ralf Baechle
Pavel Kiryukhin
Joachim Fenkes
Matthew Wilcox
Pablo Neira Ayuso
Jan Engelhardt
Patrick McHardy
Pavel Emelyanov
Evgeniy Polyakov