sil24 softreset timeout was > 100ms (100 loops with msleep(1)), which
turned out to be too short for some devices (ASI ARAID99 2000). This
patch converts sil24 softreset waiting loop to use proper timeout
condition and lengthen the timeout to ATA_TMOUT_BOOT secs and check
interval to 100ms. Chisato Yamauchi discovered the problem and
supplied initial patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Chisato Yamauchi <cyamauch@plamo.linet.gr.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_sil24 softreset routine used to check sata_dev_present() after
SRST is complete in the hope that SRST may do some good even when
SStatus reports no device. This is okay as long as SRST timeout is
short (> 100ms in the current code) but it seems that not all SATA
devices are happy with short SRST timeout.
This patch makes softreset exit early without performing actual SRST
if SStatus reports no device in preparation for lengthening SRST
timeout.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
mwdma_mask was not copied from port_info to probe_ent. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a new PCI ID for SiI 3124. Reported by Silicon Image.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carlos Pardo <Carlos.Pardo@siliconimage.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The previous dev->max_sectors patch made sht->max_sectors meaningless.
Kill all initializations of sht->max_sectors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
cdb_len is per-device property. Sharing cdb_len on ap results in
inaccurate configuration on revalidation and hotplugging. This patch
makes cdb_len per-device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Now that libata is smart enough to handle both soft and hard resets,
add hardreset method. Note that sil24 hardreset doesn't supply
signature; still, the new reset mechanism can make good use of it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
->eng_timeout cannot be invoked with NULL qc anymore. Add an
assertion in ata_scsi_error() and kill NULL qc handling from all
->eng_timeout callbacks.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implement ata_eh_qc_complete/retry() using scsi_eh_finish_cmd() and
scsi_eh_flush_done_q(). This removes all eh scsicmd finish hacks from
low level drivers.
This change was first suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Return AC_ERR_* mask from issue fuctions instead of 0/-1. This
enables things like failing a qc with AC_ERR_HSM when the device
doesn't set DRDY when the qc is about to be issued.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add detailed AC_ERR_* flags and use them. Long-term goal is to
describe all errors with err_mask and tf combination (tf for failed
sector information, etc...). After proper error diagnosis is
implemented, sense data should also be generated from err_mask instead
of directly from hardware tf registers as it is currently.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Reflect changes in SCSI midlayer and updated to use new
ordered request implementation
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
- remove err_mask from the parameter list of the complete functions
- move err_mask to ata_queued_cmd
- initialize qc->err_mask when needed
- for each function call to ata_qc_complete(), replace the err_mask parameter with qc->err_mask.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
===============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sil24_error_intr logs all error interrupts. ATAPI devices generates
many harmless errors which can be ignored and all serious ones are
reported via sense data by SCSI layer. Don't log device errors from
ATAPI devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements ATAPI support for sil24 and bumps driver version
to 0.23.
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, it has been converted to use ->dev_config as pointed out.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There seems to be no way to obtain device signature from sil24 after
SATA phy reset and SRST is needed anyway for later port multiplier
suppport. This patch converts sil24_phy_reset to use SRST instaed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, I didn't remove the 10ms sleep just to be on the safe side. I
think we can live with 10ms sleep on SRST.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When an error condition is raised by device via D2H FIS or SDB. sil24
controller should be restarted by setting PORT_CS_INIT and waiting
until PORT_CS_RDY is asserted instead of resetting the controller.
This patch implements sil24_restart_controller for those cases. This
patch also makes sure that PORT_CS_RDY is asserted on
sil24_reset_controller completion.
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, delay is reduced to 1us and cnt increased to 10k. My sil3124
turns on PORT_CS_RDY on the second iteration even without any delay.
I think 10k * 1us should be more than enough.
I tried to convert both restart and reset to use msleep's with work
queue, but if we do that, host_set lock should be released after
initiating restart or reset, leading to race condition among
reset/restart, other interrupts and timeout. Implementing
synchronization among those in low-level driver doesn't seem right.
Well, reduced timeout should work for the time being.
Thanks.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adds constants for ATAPI support to sata_sil24. This patch is
originally from Jeff Garzik <jgarzik@pobox.com>.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sil24_port_stop() is missing call to ata_pad_free() thus leaking pad
buffer when a port is stopped. This patch adds it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use ata_pad_{alloc,free} in two drivers, to factor out common code.
Add ata_pad_{alloc,free} to two other drivers, which needed the padding
but had not been updated.
The second argument to ata_qc_complete() was being used for two
purposes: communicate the ATA Status register to the completion
function, and indicate an error. On legacy PCI IDE hardware, the latter
is often implicit in the former. On more modern hardware, the driver
often completely emulated a Status register value, passing ATA_ERR as an
indication that something went wrong.
Now that previous code changes have eliminated the need to use drv_stat
arg to communicate the ATA Status register value, we can convert it to a
mask of possible error classes.
This will lead to more flexible error handling in the future.
This patch adds support for sil_3131 and sil_3531. Both are
identical to 3124 except that they have only one port. Bits 30 and 31
of ata_port_info->host_flags is used to encode available port numbers.
Version number is bumped to 0.22.
Edward Falk supplied all the necessary information and preliminary
patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Hello, guys.
This patch implements ->tf_read callback for sil24. It didn't use to
be necessary but new ata_gen_fixed_sense now makes use of ->tf_read
callback. This patch is taken from Edward Falk's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
03_sil24_add-tf-reading.patch
This patch implements proper TF register reading back and
caching and bumps up version to 0.22. This is taken from
Edward's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 50 +++++++++++++++++++++++++++++++++++++++++++++-----
1 file changed, 45 insertions(+), 5 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
01_sil24_ignore-non-error-exception-irqs.patch
Do not error-finish commands for non-error exception irqs -
just ignore them. This is taken from Edward's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 11 ++++++++++-
1 file changed, 10 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sil24 0.20 didn't use to perform (what seems to be) port multiplier
initialization and controller reset 0.10 driver does. This makes some
sil24 controllers malfunction. This patch adds PM initialization and
controller resetting to initilization and bumps version to 0.21.
Please refer to the following thread for more information.
http://marc.theaimsgroup.com/?l=linux-ide&m=112582819830324&w=2http://marc.theaimsgroup.com/?l=linux-ide&m=112636045531060&w=2
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
03_sil24_add-pci-fault-check.patch
On entry to interrupt handler, PORT_SLOT_STAT register is read
first. Check if PCI fault or device removal has occurred by
testing the value for 0xffffffff.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 6 ++++++
1 files changed, 6 insertions(+)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
02_sil24_remove-irq-disable-on-spurious-intr.patch
If interrupt occurs on a disabled port, the driver used to
mask the port's interrupt, but we don't know if such action is
necessary yet and that's not what other drives do. So, just
do nothing and tell IRQ subsystem that it's not our interrupt.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 15 +++++----------
1 files changed, 5 insertions(+), 10 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Tejun Heo
Albert Lee
Jeff Garzik
Al Viro