__asr_toggle() is always called with asr_lock held.
But there is unnecessary spin_unlock() call in __asr_toggle().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch updates the maintainers email address for Liam Girdwood and
adds a URL for the ASoC website.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kernel/time/tick-common.c: In function ‘tick_setup_periodic’:
kernel/time/tick-common.c:113: error: implicit declaration of function ‘tick_broadcast_oneshot_active’
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Functional TSC is marked unstable on AMD family 0x10 and 0x11 CPUs.
This would be wrong because for those CPUs "invariant TSC" means:
"The TSC counts at the same rate in all P-states, all C states, S0,
or S1"
(See "Processor BIOS and Kernel Developer's Guides" for those CPUs.)
[ tglx: Changed C1E to AMD C1E in the printks to avoid confusion
with Intel C1E ]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: System hang when AMD C1E machines switch into C2/C3
AMD C1E enabled systems do not work with normal ACPI C-states
even if the BIOS is advertising them. Limit the C-states to
C1 for the ACPI processor idle code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: timer hang on CPU online observed on AMD C1E systems
When a CPU is brought online then the broadcast machinery can
be in the one shot state already. Check this and setup the timer
device of the new CPU in one shot mode so the broadcast code
can pick up the next_event value correctly.
Another AMD C1E oddity, as we switch to broadcast immediately and
not after the full bring up via the ACPI cpu idle code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: Possible hang on CPU online observed on AMD C1E machines.
The broadcast setup code looks at the mode of the tick device to
determine whether it needs to be shut down or setup. This is wrong
when the broadcast mode is set to one shot already. This can happen
when a CPU is brought online as it goes through the periodic setup
first.
The problem went unnoticed as sane systems do not call into that code
before the switch to one shot for the clock event device happens.
The AMD C1E idle routine switches over immediately and thereby shuts
down the just setup device before the first interrupt happens.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: possible hang on CPU onlining in timer one shot mode.
The tick_next_period variable is only used during boot on nohz/highres
enabled systems, but for CPU onlining it needs to be maintained when
the per cpu clock events device operates in one shot mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: hang which happens across CPU offline/online on AMD C1E systems.
When a CPU goes offline then the corresponding bit in the broadcast
mask is cleared. For AMD C1E enabled CPUs we do not reenable the
broadcast when the CPU comes online again as we do not clear the
corresponding bit in the c1e_mask, which keeps track which CPUs
have been switched to broadcast already. So on those !$@#& machines
we never switch back to broadcasting after a CPU offline/online cycle.
Clear the bit when the CPU plays dead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: rare hang which can be triggered on CPU online.
tick_do_timer_cpu keeps track of the CPU which updates jiffies
via do_timer. The value -1 is used to signal, that currently no
CPU is doing this. There are two cases, where the variable can
have this state:
boot:
necessary for systems where the boot cpu id can be != 0
nohz long idle sleep:
When the CPU which did the jiffies update last goes into
a long idle sleep it drops the update jiffies duty so
another CPU which is not idle can pick it up and keep
jiffies going.
Using the same value for both situations is wrong, as the CPU online
code can see the -1 state when the timer of the newly onlined CPU is
setup. The setup for a newly onlined CPU goes through periodic mode
and can pick up the do_timer duty without being aware of the nohz /
highres mode of the already running system.
Use two separate states and make them constants to avoid magic
numbers confusion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LD kernel/built-in.o
WARNING: kernel/built-in.o(.text+0x326): Section mismatch in reference
from the function init_hrtick() to the variable
.cpuinit.data:hotplug_hrtick_nb.8
The function init_hrtick() references
the variable __cpuinitdata hotplug_hrtick_nb.8.
This is often because init_hrtick lacks a __cpuinitdata
annotation or the annotation of hotplug_hrtick_nb.8 is wrong.
Signed-off-by: Md.Rakib H. Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
27-rc fails to boot up if configured to use modules.
Turns out vsmp_patch was marked __init, and vsmp_patch being the
pvops 'patch' routine for vsmp, a call to vsmp_patch just turns out
to execute a code page with series of 0xcc (POISON_FREE_INITMEM -- int3).
vsmp_patch has been marked with __init ever since pvops, however,
apply_paravirt can be called during module load causing calls to
freed memory location.
Since apply_paravirt can only be called during init/module load, make
vsmp_patch with "__init_or_module"
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The wdt285.c watchdog driver is producing a number of
sparse errors due to missing __user attributes to calls
to put_user and copy_to_user, as well as in the prototype
of watchdog_write.
wdt285.c:144:21: warning: incorrect type in argument 1 (different address spaces)
wdt285.c:144:21: expected void [noderef] <asn:1>*to
wdt285.c:144:21: got void *<noident>
wdt285.c:150:9: warning: incorrect type in initializer (different address spaces)
wdt285.c:150:9: expected int const [noderef] <asn:1>*register __p
wdt285.c:150:9: got int *<noident>
wdt285.c:159:9: warning: incorrect type in initializer (different address spaces)
wdt285.c:159:9: expected int const [noderef] <asn:1>*register __p
wdt285.c:159:9: got int *<noident>
wdt285.c:174:9: warning: incorrect type in initializer (different address spaces)
wdt285.c:174:9: expected int const [noderef] <asn:1>*register __p
wdt285.c:174:9: got int *<noident>
wdt285.c:183:12: warning: incorrect type in initializer (incompatible argument 2 (different address spaces))
wdt285.c:183:12: expected int ( *write )( ... )
wdt285.c:183:12: got int ( static [toplevel] *<noident> )( ... )
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
__asr_toggle() is always called with asr_lock held.
But there is unnecessary spin_unlock() call in __asr_toggle().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Just like in the arch/sparc64/kernel/of_device.c code fix commit
071d7f4c3b411beae08d27656e958070c43b78b4 ("sparc64: Fix SMP bootup
with CONFIG_STACK_DEBUG or ftrace.") we have to check the OF device
node name for "pci" instead of relying upon the 'device_type' property
being there on all PCI bridges.
Tested by Meelis Roos, and confirmed to make the PCI QFE devices
reappear on the E3500 system.
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB transport specification for Bluetooth splits the ACL and SCO
handling into two separate interfaces. In Linux it possible to probe
and disconnect these interfaces independently. So make sure that both
interfaces are tightly bound together.
This fixes the suspend regression that some people have expierenced.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The btusb driver contains two typos that result in some buggy behavior,
but the impact is not immediately visible.
During initialization the submitting of interrupt URBs might fail and
then make sure to remove the correct flag and not one of the hci_dev
flags.
When closing down the interface make sure to kill the anchor for the
ISOC URBs and not kill the interrupt URBs twice.
Also cancel any scheduled work when closing down the interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The newer MacBooks contain a Broadcom based Bluetooth chip and to make
this work properly, HCI_Reset must be send first. If HCI_Reset is not
used then a lot of I/O errors show up and its triggers packets from
non-existent ACL links.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently a memory segment in memory map with attribute of EFI_MEMORY_UC
is denoted as "System RAM" in /proc/iomem, while memory of attribute
(EFI_MEMORY_WB|EFI_MEMORY_UC) is also labeled the same.
The kexec utility then includes uncached memory as part of vmcore. The
kdump kernel MCA'ed when it tries to save the vmcore to a disk. A normal
"cached" access may cause MCAs.
This patch would label memory with attribute of EFI_MEMORY_UC only as
"Uncached RAM" so that kexec would know not to include it in the vmcore.
I will submit a separate kexec-tools patch to the kexec list.
Signed-off-by: Jay Lan <jlan@sgi.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Peter Chubb reported that commit 3463a93def
(Update check_sal_cache_flush to use platform_send_ipi()) broke
Ski because it does not implement IPIs.
Tony Luck suggested we just #ifndef out the call (since the simulator
does not have the SAL bug that this code is attempting to detect and
workaround)
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
akpm: taken from http://bugzilla.kernel.org/show_bug.cgi?id=11587
I bought the wifi dongle trust nw-3100 wich is in fact a zd1211rw. Its
hardware id was missing in the sources, adding it made it work flawlessly.
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Connectivtiy is lost after Group rekeying is done. The keytype
maintained by ath9k is reset when group key is updated. Though
sc_keytype can be reset only for broadcast key the proper fix
would be to use mac80211 provided key type from txinfo during
xmit and get rid of sc_keytype from ath9k ath_softc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Tested-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCMCIA abuses dev->private_data in the probe methods. Unfortunately it
continues to abuse it after calling drv->probe() which leads to crashes and
other nasties (such as bogus probes of multifunction devices) giving errors like
pcmcia: registering new device pcmcia0.1
kernel: 0.1: GetNextTuple: No more items
Extract the passed data before calling the driver probe function that way
we don't blow up when the driver reuses dev->private_data as its right.
As its close to the final release just move the hack so it works out,
hopefully someone will be sufficiently embarrassed to produce a nice rework
for 2.6.28.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: jornada720_ts - fix build error ( LONG() usage )
Input: bcm5974 - switch back to normal mode when closing
* Normalize some S: entries to match the enumeration at the beginning
of the file.
* Change one mailing list entry from S: to L:.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Drop trailing whitespace.
* Replace spaces and combinations of spaces and tabs by single tabs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The -ffunction-sections puts each text in .text.function_name section.
Without this patch, most functions are placed outside _text..._etext
area and it breaks show_stacktrace(), etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If an interrupt happened between checking of NEED_RESCHED and WAIT
instruction, adjust EPC to restart from checking of NEED_RESCHED.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use unsigned loads to avoid possible misscalculation of IP checksums. This
bug was instruced in f761106cd728bcf65b7fe161b10221ee00cf7132 (lmo) /
ed99e2bc1d (kernel.org).
[Original fix by Atsushi. Improved instruction scheduling and fix for
unaligned unsigned load by me -- Ralf]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently simple_tx_hash is hashing inside of udp fragments. As a result
packets are getting getting sent to all queues when they shouldn't be.
This causes a serious performance regression which can be seen by sending
UDP frames larger than mtu on multiqueue devices. This change will make
it so that fragments are hashed only as IP datagrams w/o any protocol
information.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Meelis Roos.
The OF device layer builds properties by matching bus types and
applying 'range' properties as appropriate, up to the root.
The match for "PCI" busses is looking at the 'device_type' property,
and this does work %99 of the time.
But on an E3500 system with a PCI QFE card, the DEC 21153 bridge
sitting above the QFE network interface devices has a 'name' of "pci",
but it completely lacks a 'device_type' property. So we don't match
it as a PCI bus, and subsequently we end up with no resource values at
all for the devices sitting under that DEC bridge.
Signed-off-by: David S. Miller <davem@davemloft.net>
The mutex mmc_test_lock is initialized at every time mmc_test device
is probed. Probing another mmc_test device may break the mutex, if
the probe function is called while the mutex is locked.
This patch fixes it by statically initializing mmc_test_lock.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Check error from mmc_register_driver() and properly unwind
block device registration.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This allows the mmc core to detect card insertion/removal for slots that
don't have any CD pin wired up.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
We used to store a binary register snapshot in the "regs" file, so we
set the file size to be the size of this snapshot. This is no longer
valid since we switched to using seq_file.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The debugfs hook atmci_regs_show allocates a temporary buffer for
storing a register snapshot, but it doesn't free it before returning.
Plug this leak.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure that the peripheral clock is enabled before reading the MMIO
registers for the debugfs "regs" dump.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Akinobu Mita
Liam Girdwood
Ingo Molnar
Andreas Herrmann
Thomas Gleixner
Rakib Mullick
Ravikiran G Thirumalai
Wim Van Sebroeck
Ben Dooks
David S. Miller
Marcel Holtmann
Senthil Balasubramanian
Jay Lan
Alex Chiang
born.into.silence@gmail.com
Linus Torvalds
Alan Cox
Haavard Skinnemoen
Andrea Righi
Jean Delvare
Atsushi Nemoto
Ralf Baechle
Alexander Duyck