Oprofile needs to call intc_get_pending() in order to determine
whether a performance counter interrupt is pending.
Also, include the header which declares intc_get_pending() and fix the
definition to match the prototype.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
There's a duplicate clock index between USART0 and USART1 which may be
causing system crashes when USART0 is used. Change the USART0 index
to '3', indicating the clock that is actually used by USART0.
Signed-off-by: Ben Nizette <ben@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
avr32 already sees the option from init/Kconfig.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch extends the I/O resource to 0xfff000cf which will enable the
watchdog driver to access the reset cause (RCAUSE) register. Making it
capable of reporting boot status.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement at32_add_device_cf() which will add a platform_device for
the at32_cf driver (not merged yet). Separate out most of the
at32_add_device_ide() code and use it to implement
at32_add_device_cf() as well.
This changes the API in the following ways:
* The board code must initialize data->cs to the chipselect ID to
use before calling any of these functions.
* The board code must use GPIO_PIN_NONE to indicate unused CF pins.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement functions for adding platform devices for TWI, MCI, AC97C
and ABDAC. They may need to be modified to cope with platform data,
etc. when the corresponding drivers are ready to be merged, but such
changes are much less likely to conflict than adding support for a
whole new type of device.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch adds platform code for PATA devices on the AP7000.
[hskinnemoen@atmel.com: board code left out for now since stk1000
doesn't support IDE out of the box]
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
is_init() is an ambiguous name for the pid==1 check. Split it into
is_global_init() and is_container_init().
A cgroup init has it's tsk->pid == 1.
A global init also has it's tsk->pid == 1 and it's active pid namespace
is the init_pid_ns. But rather than check the active pid namespace,
compare the task structure with 'init_pid_ns.child_reaper', which is
initialized during boot to the /sbin/init process and never changes.
Changelog:
2.6.22-rc4-mm2-pidns1:
- Use 'init_pid_ns.child_reaper' to determine if a given task is the
global init (/sbin/init) process. This would improve performance
and remove dependence on the task_pid().
2.6.21-mm2-pidns2:
- [Sukadev Bhattiprolu] Changed is_container_init() calls in {powerpc,
ppc,avr32}/traps.c for the _exception() call to is_global_init().
This way, we kill only the cgroup if the cgroup's init has a
bug rather than force a kernel panic.
[akpm@linux-foundation.org: fix comment]
[sukadev@us.ibm.com: Use is_global_init() in arch/m32r/mm/fault.c]
[bunk@stusta.de: kernel/pid.c: remove unused exports]
[sukadev@us.ibm.com: Fix capability.c to work with threaded init]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Acked-by: Pavel Emelianov <xemul@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Herbert Poetzel <herbert@13thfloor.at>
Cc: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_cache_(wback|inv|wback_inv) were the earliest attempt on a generalized
cache managment API for I/O purposes. Originally it was basically the raw
MIPS low level cache API exported to the entire world. The API has
suffered from a lack of documentation, was not very widely used unlike it's
more modern brothers and can easily be replaced by dma_cache_sync. So
remove it rsp. turn the surviving bits back into an arch private API, as
discussed on linux-arch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
Introduce architecture dependent kretprobe blacklists to prohibit users
from inserting return probes on the function in which kprobes can be
inserted but kretprobes can not.
This patch also removes "__kprobes" mark from "__switch_to" on x86_64 and
registers "__switch_to" to the blacklist on x86-64, because that mark is to
prohibit user from inserting only kretprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory
condition.
Killing just one of the process threads can leave the application in a bad
state, whereas killing the entire process group would allow for the
application to restart, or be otherwise handled, and makes it very obvious
that something has gone wrong.
This change allows the entire process group to be taken down, rather
than just the one thread.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Identical handlers of PTRACE_DETACH go into ptrace_request().
Not touching compat code.
Not touching archs that don't call ptrace_request.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The variable AFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of AFLAGS with KBUILD_AFLAGS all over
the tree.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k, s390
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The variable CFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of CFLAGS with KBUILD_CFLAGS all over the
tree and enabling one to use:
make CFLAGS=...
to specify additional gcc commandline options.
One usecase is when trying to find gcc bugs but other
use cases has been requested too.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k
Test was simple to do a defconfig build, apply the patch and check
that nothing got rebuild.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
As explained on:
http://www.avrfreaks.net/index.php?nameÿphpBB2&fileÿewtopic&tS307
If the current process is preempted before it can copy RAR_SUP and
RSR_SUP both register are lost and the process will segfault as soon
as it return from the syscall since the return adress will be
corrupted.
This patch disable IRQ as soon as we enter the syscall path and
reenable them when the copy is done.
In the interrupt handlers, check if we are interrupting the srrf
instruction, if so disable interrupts and return. The interrupt
handler will be re-called immediatly when the interrupts are
reenabled.
After some stressing workload:
- find / > /dev/null in loop
- top (in ssh)
- ping -f avr32
The segfaults are not seen anymore.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Make the NGW100 bitbang i2c use open drain signaling.
Also, speed it up, so it's closer to 100 kHz ... the code paths seem
to be long enough that the udelay isn't dominating bit times. The
peak bit rate I observed was around 125 kHz, but that's with large
delays (usually before ACK/NAK) which hold the overall rate down to
around 80 kHz (call it 100 usec/byte on average).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch makes the SMC configuration take timings in clock cycles
instead of nanoseconds. A function to calculate timings in clock
cycles is added.
This patch removes the rounding troubles of the previous SMC
configuration method.
[hskinnemoen@atmel.com: fix atstk1002/atngw100 flash config]
Signed-off-by: Kristoffer Nyborg Gregertsen <gregerts@stud.ntnu.no>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Given the existing "retain_initrd" boot-time parameter defined in
init/initramfs.c, there appears to be no need for the equivalent
"keepinitrd" parameter.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
__init_end, which comes immediately before .text, is already page
aligned, and that should be more than enough for the .text section.
The reason why we need to align the .text section is because the
interrupt handler offset is ORed with EVBA, so we need to provide
enough alignment of EVBA that this OR operation works as an ADD.
Currently, the last interrupt handler is not nearly a full page away
from EVBA, so it won't be a problem.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Use PAGE_SIZE, THREAD_SIZE and L1_CACHE_BYTES instead of harcoded
constants in places where that's what we really mean.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Rename vmlinux.lds to a .S file to match other architectures.
Simplify Makefile to match the rename and deleted the unused
USE_STANDARD_AS_RULE
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement at32_add_device_usba() and use it to wire up the USBA device
on ATSTK1000 and ATNGW100.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch add multidrive support for pio driver
Signed-off-by: Matteo Vit - Dave S.r.l. <matteo.vit@dave.eu>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
When debugfs is available, /sys/kernel/debug/at32ap_clk will provide a
dump of the power manager registers and of the current clock tree. This
can help sorting out various surprises, and when making runtime PM work.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The NGW100 has a board controller which is hooked up to the TWI lines
on AP7000. Since the TWI driver isn't in mainline, use the i2c-gpio
driver in the mean time.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add GPIO led support: J2 to either block of LEDs on the STK1000.
This uses the new LEDS_GPIO driver, and sets up a heartbeat trigger by
default ... either bright (!!) amber, or a more interesting purple.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Convert from struct class_device to struct device
leds: leds-gpio for ngw100
leds: Add warning printks in error paths
leds: Fix trigger unregister_simple if register_simple fails
leds: Use menuconfig objects II - LED
leds: Teach leds-gpio to handle timer-unsafe GPIOs
leds: Add generic GPIO LED driver
This patch completes Linus's wish that the fault return codes be made into
bit flags, which I agree makes everything nicer. This requires requires
all handle_mm_fault callers to be modified (possibly the modifications
should go further and do things like fault accounting in handle_mm_fault --
however that would be for another patch).
[akpm@linux-foundation.org: fix alpha build]
[akpm@linux-foundation.org: fix s390 build]
[akpm@linux-foundation.org: fix sparc build]
[akpm@linux-foundation.org: fix sparc64 build]
[akpm@linux-foundation.org: fix ia64 build]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Still apparently needs some ARM and PPC loving - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The STK1000 uses pullups on the MDIO lines to the PHY, but they are
too weak. This causes the PHY layer to detect PHYs on all possible MII
addresses. Mask out all but the correct address to prevent this from
happening.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This code is inside an #ifdef with a misspelled config symbol, so it
hasn't been used for a long time. Fix it before fixing the config
symbol to keep bisection working.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch adds register definitions, clocks and IRQs to the platform devices.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds some STK1002-specific config options covering the jumper settings,
so the kernel can automatically be configured to include the relevant devices.
One of them replaces the previous internal SW2_DEFAULT setting; SPI config
is affected by two of the jumpers; and a fourth one switches between LCD and
the second Ethernet connector. (There's more that to be done.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch enables CPU frequency scaling for AT32AP devices. This will
enable the CPU to scale between the speed of the high speed bus and
the master clock and thus save some power.
The patch also adds a parent to cpu_clk and a cpu_clk_set_rate to
enable changing the CPU clock divider in a sane way.
The driver does not check if the given rate is 0, thus resulting in a
div by 0. I think this check should be go into the clk_set_rate
framework, and not here.
Tested on AT32AP7000/ATSTK1000.
Hardware documentation can be found in the AT32AP7000 datasheet.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Split the SM platform device into separate platform devices for PM,
RTC, WDT and EIC. This is more correct according to the documentation
and allows us to simplify the code a little.
Also turn the EIC driver into a real platform driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Identical implementations of PTRACE_POKEDATA go into generic_ptrace_pokedata()
function.
AFAICS, fix bug on xtensa where successful PTRACE_POKEDATA will nevertheless
return EPERM.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the kernel OOPSed or BUGed then it probably should be considered as
tainted. Thus, all subsequent OOPSes and SysRq dumps will report the
tainted kernel. This saves a lot of time explaining oddities in the
calltraces.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Added parisc patch from Matthew Wilson -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current generic bug implementation has a call to dump_stack() in case a
WARN_ON(whatever) gets hit. Since report_bug(), which calls dump_stack(),
gets called from an exception handler we can do better: just pass the
pt_regs structure to report_bug() and pass it to show_regs() in case of a
warning. This will give more debug informations like register contents,
etc... In addition this avoids some pointless lines that dump_stack()
emits, since it includes a stack backtrace of the exception handler which
is of no interest in case of a warning. E.g. on s390 the following lines
are currently always present in a stack backtrace if dump_stack() gets
called from report_bug():
[<000000000001517a>] show_trace+0x92/0xe8)
[<0000000000015270>] show_stack+0xa0/0xd0
[<00000000000152ce>] dump_stack+0x2e/0x3c
[<0000000000195450>] report_bug+0x98/0xf8
[<0000000000016cc8>] illegal_op+0x1fc/0x21c
[<00000000000227d6>] sysc_return+0x0/0x10
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add GPIO leds to the NGW100 platform and its defconfig.
Access through /sys/class/leds/{a,b,sys}/* files; one
defaults to a heartbeat.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Haavard Skinnemoen
ben.nizette@iinet.net.au
Adrian Bunk
Hans-Christian Egtvedt
Alejandro Martinez Ruiz
Kristoffer Nyborg Gregertsen
Matt LaPlante
Serge E. Hallyn
Ralf Baechle
Linus Torvalds
Masami Hiramatsu
Will Schmidt
Alexey Dobriyan
Sam Ravnborg
Philippe Rétornaz
David Brownell
Robert P. J. Day
Sam Ravnborg
Matteo Vit
Nick Piggin
David Brownell
Alexey Dobriyan
Pavel Emelianov
Heiko Carstens