- Don't add dac load detection property to DVI-D
- Make sure i2c info is valid before adding DP aux chan bus
- Don't create scaling_mode_property twice
- fix typo that prevented coherent and load detection from working
- add coherent prop to DP (for dp->dvi adapters)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometimes we will use a crtc for integerated LVDS, which is different with
that assigned by BIOS. If we want to get flicker-free transitions,
then we could read out the current state for it and set our current state
accordingly.
But it is true that if we aren't reading current state out, we do need
to turn everything off before modesetting. Otherwise the clocks can get very
angry and we get things worse than a flicker at boot.
In fact we also do the similar thing in UMS mode. We will disable all the
possible outputs/crtcs for the first modesetting.
So we disable all the possible outputs/crtcs before entering the KMS mode.
Before we configure connector/encoder/crtc, the function of
drm_helper_disable_unused_function can disable all the possible outputs/crtcs.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Rafal Milecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rather than restoring just a few clock gating registers on resume,
just reinitialize the whole thing.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
[anholt: Fixed up for RC6 support landed since the patch was written]
Signed-off-by: Eric Anholt <eric@anholt.net>
This merges the radeon KMS DisplayPort and hotplug detect support.
Tested on RV635 DP card with a Dell 2408 monitor.
Conflicts:
drivers/gpu/drm/drm_fb_helper.c
This merges the upstream Intel tree and fixes up numerous conflicts
due to patches merged into Linus tree later in -rc cycle.
Conflicts:
drivers/char/agp/intel-agp.c
drivers/gpu/drm/drm_dp_i2c_helper.c
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/i915_suspend.c
This enabled interrupt driven hpd support for all
radeon chips. Assuming the hpd pin is wired up
correctly, the driver will generate uevents on
digital monitor connect and disconnect and retrain
DP monitors automatically.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This just adds the functionality, it's not hooked up
yet.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This just adds the functionality, it's not hooked up
yet.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This just adds the functionality, it's not hooked up
yet.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This populates the connectors with HPD (Hot Plug Detect)
information. This will be used in subsequent patches
for automatic digital monitor connect/disconnect handling.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
only return connected if there is actually a
monitor connected.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This moves the radeon DP link training call to happen when we
dpms on the encoder not when we set the mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not returning here caused us to get a display port version of 0 for everything
this caused power up to not get sent which ends up in a black screen.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will be used laster when the encoder and transmitters
are set up.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- keep the atom i2c id in the i2c rec
- fix gpio regs for GPIO and MDGPIO on pre-avivo chips
- track whether the i2c line is hw capable
- track whether the i2c line uses the multimedia i2c block
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- dpcp -> dpcd
- fix up dig encoder routing
- aux transaction table takes delay in 10 usec units
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some BIOSes fail to initialise the GTT, which will cause DMA faults when
the IOMMU is enabled. We need to clear the whole thing to point at the
scratch page, not just the part that Linux is going to use.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[anholt: Note that this may also help with stability in the presence of
driver bugs, by not drawing to memory we don't own]
Signed-off-by: Eric Anholt <eric@anholt.net>
None of the in-tree drivers use user objects yet so this wasn't hitting
us.
Stanse found unreachable code in ttm_bo_add_ttm:
http://decibel.fi.muni.cz/~xslaby/stanse/error.cgi?db=32&id=714#l238
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Both radeon and nouveau can re-use this code so move it up a level
so they can. However the hw interfaces for aux ch are different
enough that the code to translate from mode, address, bytes
to actual hw interfaces isn't generic, so move that code into the
Intel driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
IGD* isn't a useful name. Replace with the codenames, as sourced from
pci.ids.
Signed-off-by: Adam Jackson <ajax@redhat.com>
[anholt: Fixed up for merge with pineview/ironlake changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
Grab pll ref div from regs at driver init. r4xx seems very
picky about the dividers for the pll driving lvds.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DDX and radeonfb always set these regs to a sane value.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These can end up with garbage otherwise.
fixes rh bug 537140
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
FB read/write really doesn't need to access the actual VRAM, we
can just use a scratch area. This is required for using atom displayport
calls later.
Signed-off-by: Dave Airlie <airlied@redhat.com>
IGD* isn't a useful name. Replace with the codenames, as sourced
from pci.ids.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
These are handled by the error return being propagated to user-space and
do not any add any information to the original error, so are useless.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch brings the tree up to date with some fixes that were in a
more recent version of the page flipping patch you applied. It fixes
pre-965 flip support, removes a leftover hack that forced alignment,
and initializes the pipe & plane CRTC mappings.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Utilities to reserve, unreserve and fence a list of TTM
buffer objects in a deadlock-safe manner.
Used by the vmwgfx driver.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is intended to be used by ttm-aware drivers to
1) Block clients to inactive masters when
they try to validate buffers for GPU use.
2) Optionally block clients to the current master when
there is thrashing due to GPU memory shortage.
Used by the vmwgfx driver.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add objects needed for user-space to maintain reference counts on ttm objects.
This is used by the vmwgfx driver which allows user-space to maintain
map-counts on dma buffers, lock-counts on the ttm lock and ref-counts on
gpu surfaces, gpu contexts and dma buffer.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher
Dave Airlie
Zhao Yakui
Andrew Lutomirski
Ben Skeggs
Chris Wilson
David Woodhouse
Adam Jackson
Jesse Barnes
Thomas Hellstrom