This simple patch adds support to i2c-parport for the One For All remote
JP1 parallel port interfaces which can be found detailed at:
http://www.hifi-remote.com/jp1/hardware.shtml
These allow access to the internal configuration EEPROM on various
remote controls and there are a variety of Windows tools that make use
of this hardware. I have tested this patch with the "simple" parallel
port device and a One For All URC-7562 and confirmed that the data read
using the eeprom i2c driver matches that returned by the Windows "IR"
JP1 tool.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We do not have any documentation for the CX700, but it was reported
to work fine. Thanks to Claas Langbehn for testing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
IDs have been defined but not used by most of the I2C adapters.
By having a unique ID, clients can check for correct connection
during probe.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c-core and i2c-isa use completions without including
<linux/completion.h>. Fix it.
i2c-powermac includes <linux/completion.h> but doesn't use any
completion. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
The i2c-ali1563 initialization looks quite broken to me:
* If the I/O space isn't enabled, we forcibly set 3 bits in
the PCI configuration space instead of just the one enabling
the I/O space.
* After that we pretend to check if the write worked, but we
don't actually read the new value from the register.
* It's probably not a good idea to enable the I/O space if no
base address has been set.
So I propose the following changes to that part of the driver:
* Merge ali1563_enable() into ali1563_setup().
* Check the base address before the I/O space enabled bit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Improve the status messages printed by the i2c-ali1563 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Switch the i2c-pxa driver to actually using the platform device information and let it handle the power i2c bus on pxa27x too. Original version of this patch didn't compile with CONFIG_I2C_PXA_SLAVE set.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I have a Marvell board which has the same i2c hw block than mv64xxx, so
I'm trying to use i2c-mv64xxx driver.
But I get the following random oops at boot:
Unable to handle kernel NULL pointer dereference at virtual address 00000002
Backtrace:
[<c0397e4c>] (mv64xxx_i2c_intr+0x0/0x2b8) from [<c02879c4>] (__do_irq+0x4c/0x8c)
[<c0287978>] (__do_irq+0x0/0x8c) from [<c0287c0c>] (do_level_IRQ+0x68/0xc0)
r8 = C0501E08 r7 = 00000005 r6 = C0501E08 r5 = 00000005
r4 = C048BB78
[<c0287ba4>] (do_level_IRQ+0x0/0xc0) from [<c02885f8>] (asm_do_IRQ+0x50/0x134)
r6 = C0449C78 r5 = F1020000 r4 = FFFFFFFF
[<c02885a8>] (asm_do_IRQ+0x0/0x134) from [<c02869c4>] (__irq_svc+0x24/0x100)
r8 = C1CAC400 r7 = 00000005 r6 = 00000002 r5 = F1020000
r4 = FFFFFFFF
[<c0287efc>] (setup_irq+0x0/0x124) from [<c02880d0>] (request_irq+0xb0/0xd0)
r7 = C041B2AC r6 = C0397E4C r5 = 00000000 r4 = 00000005
[<c0288020>] (request_irq+0x0/0xd0) from [<c03985f4>] (mv64xxx_i2c_probe+0x148/0x244)
[<c03984ac>] (mv64xxx_i2c_probe+0x0/0x244) from [<c038bedc>] (platform_drv_probe+0x20/0x24)
The oops is caused by a spurious interrupt that occurs when request_irq
is called. mv64xxx_i2c_fsm() tries to read drv_data->msg, which is NULL.
I noticed that hardware init is done after requesting irq. Thus any
pending irq from previous hardware usage may cause this.
The following patch fixes it:
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This fixes two issues raised by David Brownell on the i2c list:
<< Someone needs to update i2c-pnx.c to handle the IRQ handler doesn't
expect pt_regs (gone now for a while), and so it doesn't try to
reference "mudule_init()" if I2C isn't initialized "early". For
that matter, to get rid of that _option_ to initialize then, and
always init that driver with subsystem_init() ... it's common with
embedded systems to need I2C access to tweak a GPIO expander or
do some other work when bringing up drivers, that's not specific
to USB stacks. >>
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: Add MAINTAINERS entry for new ams driver
hwmon: New AMS hardware monitoring driver
hwmon/w83793: Add documentation and maintainer
hwmon: New Winbond W83793 hardware monitoring driver
hwmon: Update Rudolf Marek's e-mail address
hwmon/f71805f: Fix the device address decoding
hwmon/f71805f: Always create all fan inputs
hwmon/f71805f: Add support for the Fintek F71872F/FG chip
hwmon: New PC87427 hardware monitoring driver
hwmon/it87: Remove the SMBus interface support
hwmon/hdaps: Update the list of supported devices
hwmon/hdaps: Move the DMI detection data to .data
hwmon/pc87360: Autodetect the VRM version
hwmon/f71805f: Document the fan control features
hwmon/f71805f: Add support for "speed mode" fan speed control
hwmon/f71805f: Support DC fan speed control mode
hwmon/f71805f: Let the user adjust the PWM base frequency
hwmon/f71805f: Add manual fan speed control
hwmon/f71805f: Store the fan control registers
Add support for the I2C bus found on the ARM Versatile and Realview
platforms. The I2C bus has a RTC and optionally some EEPROMs attached.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the I2C (Two-wire interface) controller integrated in
the Atmel AT91RM9200 processor. This driver should also be usable on
the Atmel AT91SAM9261 and AT91SAM9260 processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Summary of changes:
- fixes:
o legacy I/O region size is 64 bytes, not 8 bytes
- general cleanup:
o removed code for the unsupported I2C block data, block data,
proc call and block proc call transfer modes
o removed detail warnings about unsupported modes that are
covered in a general warning (unsupported transaction...)
anyway
o removed necessity of a definition of struct i2c_adapter
o moved definition of struct i2c_algorithm, making forward
declarations of nforce2_access and nforce2_func unnecessary
- minor changes:
o in the description mention the nForce 5xx chipsets
o changes my e-mail address in MODULE_AUTHOR
Theses cleanups shrink the driver binary size from 4.0 kB to 2.7 kB
on i386.
Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reserving I/O memory for a driver with request_mem_region is necessary to
avoid memory access conflicts. Even if it's never going to happen, it is
cleaner and it allows to monitor I/O memory used in /proc/iomem.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@teamlog.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
New I2C bus driver for Philips ARM boards (Philips IP3204 I2C IP
block). This I2C controller can be found on (at least) PNX010x,
PNX52xx and PNX4008 Philips boards.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The rest of the ITE8172 support was already removed from MIPS tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
[ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
[ARM] 4001/1: S3C24XX: shorten reboot time
[ARM] 3983/2: remove unused argument to __bug()
[ARM] 4000/1: Osiris: add third serial port in
[ARM] 3999/1: RX3715: suspend to RAM support
[ARM] 3998/1: VR1000: LED platform devices
[ARM] 3995/1: iop13xx: add iop13xx support
[ARM] 3968/1: iop13xx: add iop13xx_defconfig
[ARM] Update mach-types
[ARM] Allow gcc to optimise arm_add_memory a little more
[ARM] 3991/1: i.MX/MX1 high resolution time source
[ARM] 3990/1: i.MX/MX1 more precise PLL decode
[ARM] 3986/1: H1940: suspend to RAM support
[ARM] 3985/1: ixp4xx clocksource cleanup
[ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
[ARM] 3994/1: ixp23xx: fix handling of pci master aborts
[ARM] 3981/1: sched_clock for PXA2xx
[ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
[ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
[ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
...
Merge:
Atmel AT91RM9200 and AT91SAM9260 changes
General ARM developments
Disconfiguous memory cleanups
64-bit/32-bit division and sched_clock extension patches
EP93xx support changes
IOP support changes
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The iop348 processor integrates an Xscale (XSC3 512KB L2 Cache) core with a
Serial Attached SCSI (SAS) controller, multi-ported DDR2 memory
controller, 3 Application Direct Memory Access (DMA) controllers, a 133Mhz
PCI-X interface, a x8 PCI-Express interface, and other peripherals to form
a system-on-a-chip RAID subsystem engine.
The iop342 processor replaces the SAS controller with a second Xscale core
for dual core embedded applications.
The iop341 processor is the single core version of iop342.
This patch supports the two Intel customer reference platforms iq81340mc
for external storage and iq81340sc for direct attach (HBA) development.
The developer's manual is available here:
ftp://download.intel.com/design/iio/docs/31503701.pdf
Changelog:
* removed virtual addresses from resource definitions
* cleaned up some unnecessary #include's
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updated patch adds the Intel ICH9 LPC and SMBus Controller DID's. Thi=
s patch relies on the irq ICH9 patch to pci_ids.h.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The i2c-pxa driver should not contain EEPROM slave-mode emulation;
this is something the platform should provide where required. Remove
it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i2c-pxa times out when trying to enable slave mode due to an
incorrect test. Also, check that i2c->slave is non-NULL
before dereferencing it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let the w83781d and lm78 hardware monitoring drivers load even when
no chip was detected at the ISA address. There can still be supported
chips connected to an I2C bus or SMBus.
This fixes bug #7293.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-powermac was written & merged right after Russell King's changes
adding platform_driver... which I missed. Thus it still used struct
device, causing crashes when hitting sleep/wakeup callbacks (it happened
to work by luck so far, until early/late callbacks got added). This
causes crashes on sleep/wakeup on PowerBooks with 2.6.19. The patch
fixes it by using a proper platform_driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix undefined reference in i2c_sibyte_exit().
drivers/built-in.o: In function `i2c_sibyte_exit':
i2c-sibyte.c:(.exit.text+0x368): undefined reference to `i2c_del_bus'
i2c-sibyte.c:(.exit.text+0x368): relocation truncated to fit: R_MIPS_26 against `i2c_del_bus'
i2c-sibyte.c:(.exit.text+0x38c): undefined reference to `i2c_del_bus'
i2c-sibyte.c:(.exit.text+0x38c): relocation truncated to fit: R_MIPS_26 against `i2c_del_bus'
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i2c: Constify i2c_algorithm declarations, part 2
Make struct i2c_algorithm declarations const in all i2c bus drivers
where it is possible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-viapro: Add support for the VT8237A and VT8251
Documentation update included. Compile tested.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-algo-pcf: Discard the mdelay data struct member
Just as i2c-algo-bit, i2c-algo-pcf has an unused mdelay struct member,
which we can get rid of to spare some code and memory.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-stub: Chip address as a module parameter
Add a mandatory chip_addr parameter to i2c-stub. This parameter
defines to which chip address the driver will respond, instead of
reponding to all addresses as before. The idea is to prevent the
users from loading i2c-stub at random and being then confused by
the results of sensors-detect or other user-space tools.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c: New bus driver for TI OMAP boards
This patch adds I2C bus driver for various Texas
Instruments (TI) OMAP1/2 (http://www.ti.com/omap) series
based boards like OMAP1510/1610/1710/242x.
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-algo-bit: Discard the mdelay data struct member
The i2c_algo_bit_data structure has an mdelay member, which is not
used by the algorithm code (the code has always been ifdef'd out.)
Let's discard it to save some code and memory.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-au1550: Add SMBus functionality flag
Add SMBus functionality flag, so we can use eeprom and similar
drivers.
Signed-off-by: Domen Puncer <domen.puncer@ultra.si>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-au1550: Fix timeout problem
Fix from Jordan Crouse:
If the transmit and recieve FIFOS are not empty, forceably flush them
rather then waiting for them to drain on their own.
This solves at least a problem reported by Clem Taylor:
http://www.linux-mips.org/archives/linux-mips/2006-05/msg00240.html
(1% of I2C transactions would timeout)
Signed-off-by: Domen Puncer <domen.puncer@ultra.si>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-sibyte: Kip Walker is gone
Kip Walker no longer works at Broadcom, and his e-mail address there
bounces back, so let's drop it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-algo-sibyte: Merge into i2c-sibyte
Merge i2c-algo-sibyte into i2c-sibyte, as this is a complete,
hardware-dependent SMBus implementation and not a reusable algorithm.
Perform some basic coding style cleanups while we're here (mainly
space-based indentation replaced by tabulations.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c: __must_check fixes (core drivers)
Check for error on sysfs file creation.
Check for error on device registration.
Check for error on class device registration.
Greg, I am not familiar with completion, can you please tell me if I
need to take care of it in the error paths (as I did in this patch,
see /* Needed? */ comments), or if it isn't needed?
These patches were tested, including forced errors, so they should work
fine. But of course more testing can't hurt.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement the gpio_line_{config,get,set} API for iop3xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split the iop3xx mach type into iop32x and iop33x -- split the config
symbols, and move the code in the mach-iop3xx directory to the mach-iop32x
and mach-iop33x directories.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename CONFIG_ARCH_IOP321 to CONFIG_ARCH_IOP32X and
CONFIG_ARCH_IOP331 to CONFIG_ARCH_IOP33X.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While busy-waiting for completion, check the hardware after scheduling;
don't schedule and then immediately check the _timeout_. If the yield()
took a long time (as it does on my OLPC prototype board when it's busy),
we'd report a timeout even though the hardware was now ready.
This fixes it, and also switches the yield() for a cond_resched() because
we don't actually want to be _that_ nice about it. I see nice
tightly-packed SMBus transactions now, rather than waiting for milliseconds
between successive phases.
Actually, we shouldn't be busy-waiting here at all. We should be using
interrupts. That's an exercise for another day though.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Christer Weinigel <wingel@nano-system.com>
Cc: <Jordan.Crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
powermac platform & macintosh driver changes.
Built for pmac32_defconfig, g5_defconfig
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the value returned by the i2c-powermac's master_xfer method.
It should return the number of messages processed successfully, but
instead returns the number of data bytes in the first (and only)
processed message.
Also explicitly mention the master_xfer convention so that future
implementations get it right directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scx200_acb i2c bus driver pretends to support SMBus block
transactions, but in fact it implements the more simple I2C block
transactions. Additionally, it lacks sanity checks on the length
of the block transactions, which could lead to a buffer overrun.
This fixes an oops reported by Alexander Atanasov:
http://marc.theaimsgroup.com/?l=linux-kernel&m=114970382125094
Thanks to Ben Gardner for fixing my bugs :)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the scx200_acb state machine:
* Nack was sent one byte too late on reads >= 2 bytes.
* Stop bit was set one byte too late on reads.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid addressing self when sending a slave address. Follows instruction
in Intel 80331/80321 manuals.
Ignoring this worked previously on 80321, but causes a hang on i2cdetect
on 80331.
Signed-off-by: Peter Milne <peter.milne@d-tacq.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-i801.c: In function 'i801_probe':
drivers/i2c/busses/i2c-i801.c:496: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'resource_size_t'
Cc: Greg KH <greg@kroah.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 02dd7ae289 ("[PATCH] i2c-i801:
Merge setup function") has a missing return 0 in the _probe() function.
This means the error path is always executed and pci_disable_device() is
called even when the device just got successfully enabled.
Having the SMBus device disabled makes some systems (eg.
Fujitsu-Siemens Lifebook E8010) hang hard during power-off.
Intead of reverting the whole commit this patch fixes it up:
- don't ever call pci_disable_device(), also not in the _remove() function
to avoid hangs
- fix missing pci_release_region() in error path
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (139 commits)
[POWERPC] re-enable OProfile for iSeries, using timer interrupt
[POWERPC] support ibm,extended-*-frequency properties
[POWERPC] Extra sanity check in EEH code
[POWERPC] Dont look for class-code in pci children
[POWERPC] Fix mdelay badness on shared processor partitions
[POWERPC] disable floating point exceptions for init
[POWERPC] Unify ppc syscall tables
[POWERPC] mpic: add support for serial mode interrupts
[POWERPC] pseries: Print PCI slot location code on failure
[POWERPC] spufs: one more fix for 64k pages
[POWERPC] spufs: fail spu_create with invalid flags
[POWERPC] spufs: clear class2 interrupt status before wakeup
[POWERPC] spufs: fix Makefile for "make clean"
[POWERPC] spufs: remove stop_code from struct spu
[POWERPC] spufs: fix spu irq affinity setting
[POWERPC] spufs: further abstract priv1 register access
[POWERPC] spufs: split the Cell BE support into generic and platform dependant parts
[POWERPC] spufs: dont try to access SPE channel 1 count
[POWERPC] spufs: use kzalloc in create_spu
[POWERPC] spufs: fix initial state of wbox file
...
Manually resolved conflicts in:
drivers/net/phy/Makefile
include/asm-powerpc/spu.h
i2c-i801: Merge setup function
Merge i801_setup into i801_probe, as it doesn't make much sense to
have them split. This lets us handle errors better. Christopher
Hellwig had been suggesting this back in March 2003 when the driver
was merged.
Also drop two useless debug messages (revision and base address can be
obtained from lspci, procfs or sysfs.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Better pci subsystem integration
Integrate the i2c-i801 driver better with the pci subsystem, by
calling pci_{enable,disable}_device and requesting the I/O region
by BAR rather than direct configuration space access.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Cleanups
Various cleanups to the i2c-i801 driver:
* Fix documentation file and self file name references.
* i801_setup can be marked __devinit.
* Drop useless error local variable and label in i801_setup.
* Avoid a double PCI configuration register write in some cases.
* Use symbolic names for SMBHSTCFG bits.
* Transmit the error code returned by i801_setup instead of forcing it
to an arbitrary value.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Remove PCI function check
Remove the PCI function number check when probing devices.
This check is redundant, each function has a separate PCI device
ID, so checking for that ID is sufficient.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Remove force_addr parameter
Remove the force_addr module parameter. It doesn't appear to ever
have been needed, and PCI resources shouldn't be arbitrarily
changed anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Fix block transaction poll loops
Two of the three poll loops have the poll and sleep swapped,
causing an extra sleep to occur after the polled condition is
fulfilled. In practice, this doubles the amount of sleep time for
every block transaction.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In i2c bus driver scx200_acb, function scx200_acb_probe can be
tagged __init.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the CS5535 and CS5536, the I/O resource is allocated through PCI,
so use that instead of using the MSR backdoor.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup to the i2c-ocores driver.
Peter Korsgaard will maintain the i2c-ocores driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch adds support for the OpenCores I2C controller IP
core (See http://www.opencores.org/projects.cgi/web/i2c/overview).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Improve the Kconfig help text of the follwing i2c drivers:
* busses/i2c-pca-isa.c
* chips/pcf8574.c
* chips/pcf8591.c
These are hard to detect and building them into the kernel
results in long delays at boot.
March 2006, thread "I2C_PCA_ISA causes boot delays"
http://marc.theaimsgroup.com/?l=linux-kernel&m=114360399415744&w=2
April 2006, thread "i2c-related 1-minute hang during bootup"
http://marc.theaimsgroup.com/?l=linux-kernel&m=114640992330721&w=2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the new nForce4 MCP51 (also known as nForce 410 or
430) and nForce4 MCP55 to the i2c-nforce2 driver. Some code changes
were required because the base I/O address registers have changed in
these versions. Standard BARs are now being used, while the original
nForce2 chips used non-standard ones.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Properly document on which systems the i2c-piix4 SMBus driver will
refuse to load. Hopefully this will make it clearer for users, which
were often wondering why their destop or server systems were detected
as laptops.
Closes bug #6429.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the fix_hstcfg option from the driver and related
SMBus Interrupt Select register magic because now we know what are
valid values for this register. This patch updates the documentation
and adds new IRQ mode check so we are sure not to miss any new
"unusual" value.
The PCI quirk for users of fix_hstcfg was not developed because the
chipset lacks of subsystem ID registers and DMI is stated "To be
filled". Impact to existing systems is minimal because the problem
showed up on motherboards like 10 years back. On the other hand users
of newer Serverworks and HT1000 systems won't be misleaded by the
message suggesting to try the fix_hstcfg any more.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the ATI IXP southbridges support to i2c-piix4,
as it turned out those chips are compatible with it.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The same I2C driver found on 85xx, etc., can be used for 86xx too.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a fix for the CS5535 errata 111:
When the SMBus controller tries to access a non-existing device, it sets
the NEGACK bit, SMBus I/O offset 01h[4], to 1 after it detects no
acknowledge at the ninth clock. The specification states that the bit
can be cleared by writing a 1 to it, but under certain circumstances it
is possible for this bit to not clear.
Writing a 0 to the bit resets the internal state machine and clears the
issue.
Since all writable bits in ACBST are W1C bits (write-one-to-clear) the
second write doesn't affect any other logic except the buggy NEGACK
state machine. The second write clears an internal register which is
responsible for "overwriting" the NEGACK bit in ACBST.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can't pass a string on the stack to request_region. As soon as we
leave the function that stack is gone and the string is lost. Let's
use the same string we identify the i2c_adapter with instead, it's
more simple, more consistent, and just works.
This is the second half of fix to bug #6445.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scx200_acb driver shouldn't return failure after initialization
if it successfully registered at least one i2c_adapter, else we are
leaking resources. The driver was OK in that respect up to 2.6.16, a
recent change broke it.
This is part of the fix to bug #6445.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix for bug #6395:
Fail to resume on Tecra M2 with ADM1032 and Intel 82801DBM
The BIOS of the Tecra M2 doesn't like it when it has to reboot or resume
after the i2c-i801 driver has left the SMBus in PEC mode. The most simple
fix is to clear the PEC bit after after every transaction. That's what
this driver was doing up to 2.6.15 (inclusive).
Thanks to Daniele Gaffuri for the very good report.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch forces the user to specify what type of adapter is present when
loading i2c-parport or i2c-parport-light. If none is specified, the driver
init simply fails - instead of assuming adapter type 0.
This alleviates the sometimes lengthy boot time delays which can be caused
by accidentally building one of these into a kernel along with several i2c
slave drivers that have lengthy probe routines (e.g. hwmon drivers).
Kconfig and documentation updated accordingly.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes an init-time kernel log message.
http://marc.theaimsgroup.com/?l=linux-kernel&m=114232987208628&w=3
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds I2C_CLASS_HWMON to the ixp4xx bus driver.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Broadcom HT-1000 south bridge's PCI ID to i2c-piix driver. Note
that at least on Supermicro H8SSL it uses non-standard SMBHSTCFG = 3
and standard values like 0 or 9 causes hangup.
Signed-off-by: Martin Devera <devik@cdi.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop a redundant mutex in driver i2c-ali1535. The struct i2c_adapter
includes a mutex for the same purpose, operated by i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Properly set the name member of the i2c_adapter structure of the ite
i2c adapter driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jonathan McDowell
Jean Delvare
Stephen Hemminger
Guennadi Liakhovetski
Maxime Bizon
Vitaly Wool
Linus Torvalds
Russell King
Andrew Victor
Hans-Frieder Vogt
Jean-Baptiste Maneyrol
Russell King
Dan Williams
Jason Gaston
Jeff Garzik
Alexey Dobriyan
Benjamin Herrenschmidt
David Howells
Dave Jones
Uwe Zeisberger
Matt LaPlante
Alexey Dobriyan
Yoichi Yuasa
Linus Torvalds
Rudolf Marek
Adrian Bunk
David Hubbard
Komal Shah
Domen Puncer
Lennert Buytenhek
Paul Mackerras
David Woodhouse
Jeremy Kerr
Thomas Andrews
Peter Milne
Thomas Gleixner
Andrew Morton
Jörn Engel
Daniel Ritz
Jordan Crouse
Peter Korsgaard
Jon Loeliger
Randy Dunlap
Mark M. Hoffman
Alessandro Zummo
Martin Devera