Check if the sleep command returns due to a pending interrupt
in the standby unit. If this happens, try and ack the IRQ
before re-trying the resume.
It is currently unclear whether the resume can be backed out
of at this stage as this could cause a problem with level
based interrupts.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that if the RTC IRQ is not selected for wake in the
base configuration, then the PWRCFG has the same value set
in it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2412_GPESLPCON does not exist in the register
mappings, so remove it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 IIS engine differs from the previous
SoC in the range, so add a set of register definitions
in a seperate file for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS and SDI register hw_addr definitions are
incorrect in the DMA map for the S3C2412.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 GPIO is similar enough to the S3C2410 that
it can use it as a base for GPIO functionality.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have a default display set to 4, when we only have
three registered displays. Fix this argument (a seperate
patch has been generated to ensure that the LCD driver
takes notice of this bug)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the watchdog reset fails and we decided to take the jump
to zero approach, allow 50ms for the UARTS to drain the FIFOs
before calling into a bootloader that may flush the output.
Also reduece the waits and the timeout values as 5 seconds is
rather long.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the hard reset routine is using the watchdog, then
ensure that the clock for the watchdog has been enabled
before we try and issue a reset.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the S3C2412_PWRCFG values for the action taken on detecting that
the battery is flat.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for Toradex' PXA27x based Colibri module.
It's kept as simple as possible to only provide basic functionality.
A default config is also included.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix all those PXA mci_init functions which return -1 rather than
propagating the error code to the higher levels. Remove the silly
set_irq_type() calls as well - use the flags for request_irq()
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch refactors the code in corgi_lcd.c moving it to the board
specific corgi and spitz files where appropriate instead of the
existing ifdef mess which hinders readability.
Fix spitz_get_hsync_len() to call get_hsync_invperiod so pxafb can be
compiled as a module.
The confusing variables which represent the inverse horizintal sync
period are renamed to "invperiod" consistently.
An incorrect comment in corgi_ts.c is also corrected.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds baseboard support for the phyCORE-PXA270 development
kit (aka PCM-990).
This example shows how to use some phyCORE-PXA270 CPU module features
on a baseboard in a standard manner. It could be used as a starting
point for custom baseboard development.
V2:
After comments by Eric Miao:
- IRQ chained handler fixed
- video/graphic support moved to separate patch
- ifdef/endif hell reduced ;-)
V3:
After comments by Russell King
- initialise the mmci platform data statically
V4:
After comments by Russell King
- wrong return value in pcm990_mci_init() fixed
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds SMC91x support for the phyCORE-PXA270 CPU module (aka PCM-027).
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a basic configration for the phyCORE-PXA270 development kit. In this case development kit means PCM-990 (main baseboard).
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds main support for the generic phyCORE-PXA270 CPU module
(aka PCM-027). Its as generic as possible to support any kind of baseboard.
Note: Neither the CPU module nor the pcm027.c implementation can work without
a baseboard support. Baseboard support can be added by the PCM-990 or any
custom variant.
V2:
After comments by Eric Miao:
- Currently unsupported devices moved into separate patch
- direct call of baseboard initialisation
V3:
After comments by Russell King
- sort include files
- setting RTC bit for power control removed
- style problems fixed (discovered by checkpatch.pl)
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
smc91x is shared between many different platforms. Each platform needs
to specify the interrupt type, and in some cases the irq type depends
on more than just the build configuration - it depends on runtime
checks.
Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide
a way for these flags to be passed via the IRQ resource itself.
Note that IRQF_TRIGGER_* constants are intentionally defined to correspond
with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that
the low bits of PCI iomem resources correspond with the BAR flag bits.
Also provide a way to configure smc91x to read the IRQ flags from the
resource. Once all platforms have been converted over (signified
by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should
be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
default to
- PXA300/PXA310 support only (there isn't any littleton board with PXA320
processor for now)
- smc91x ethernet support with NFS rootfs
- LCD framebuffer support with graphics console
Signed-off-by: eric miao <eric.miao>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This includes irda, gpio keys, pxafb, backlight, ohci and flash
(read-only).
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains the base code to boot the Toshiba e330, e740,
e750, e400, and e800 PDAs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds back the registration of HWUART clock on pxa25x
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently you must be root to set idle io prio class on a process. This
is due to the fact that the idle class is implemented as a true idle
class, meaning that it will not make progress if someone else is
requesting disk access. Unfortunately this means that it opens DOS
opportunities by locking down file system resources, hence it is root
only at the moment.
This patch relaxes the idle class a little, by removing the truly idle
part (which entals a grace period with associated timer). The
modifications make the idle class as close to zero impact as can be done
while still guarenteeing progress. This means we can relax the root only
criteria as well.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move the xtime write mode seqlock into timer_tick(), so it only
surrounds the call to do_timer().
This avoids a deadlock in update_process_times() ...
hrtimer_get_softirq_time() which tries to get a read mode seqlock
on xtime, thereby preventing booting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original code incorrectly returns Hz instead of KHz.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SCSI sg table allocation has a maximum size (of SCSI_MAX_SG_SEGMENTS,
currently 128) and this will cause a BUG_ON() in SCSI if something
tries an allocation over it. This patch adds a size limit to the
chaining allocator to allow the specification of the maximum
allocation size for chaining, so we always chain in units of the
maximum SCSI allocation size.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
These DMA drain buffer implementations in drivers are pretty horrible
to do in terms of manipulating the scatterlist. Plus they're being
done at least in drivers/ide and drivers/ata, so we now have code
duplication.
The one use case for this, as I understand it is AHCI controllers doing
PIO mode to mmc devices but translating this to DMA at the controller
level.
So, what about adding a callback to the block layer that permits the
adding of the drain buffer for the problem devices. The idea is that
you'd do this in slave_configure after you find one of these devices.
The beauty of doing it in the block layer is that it quietly adds the
drain buffer to the end of the sg list, so it automatically gets mapped
(and unmapped) without anything unusual having to be done to the
scatterlist in driver/scsi or drivers/ata and without any alteration to
the transfer length.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
syslets (or other threads/processes that want io context sharing) can
set this to enforce sharing of io context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The io context sharing introduced a per-ioc spinlock, that would protect
the cfq io context lookup. That is a regression from the original, since
we never needed any locking there because the ioc/cic were process private.
The cic lookup is changed from an rbtree construct to a radix tree, which
we can then use RCU to make the reader side lockless. That is the performance
critical path, modifying the radix tree is only done on process creation
(when that process first does IO, actually) and on process exit (if that
process has done IO).
As it so happens, radix trees are also much faster for this type of
lookup where the key is a pointer. It's a very sparse tree.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts xsysace to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
xsysace is a little bit different from "normal" drivers.
xsysace driver has a state machine in it.
It calls end_that_request_first() and end_that_request_last()
from different states. (ACE_FSM_STATE_REQ_TRANSFER and
ACE_FSM_STATE_REQ_COMPLETE, respectively.)
However, those states are consecutive and without any interruption
inbetween.
So we can just follow the standard conversion rule (b) mentioned in
the patch subject "[PATCH 01/30] blk_end_request: add new request
completion interface".
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts ub to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch merges complete_request() into end_that_request_last()
for cleanup.
complete_request() was introduced by earlier part of this patch-set,
not to break the existing users of end_that_request_last().
Since all users are converted to blk_end_request interfaces and
end_that_request_last() is no longer exported, the code can be
merged to end_that_request_last().
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts 'uptodate' arguments of no longer exported
interfaces, end_that_request_first/last, to 'error', and removes
internal conversions for it in blk_end_request interfaces.
Also, this patch removes no longer needed end_io_error().
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch removes the following functions:
o end_that_request_first()
o end_that_request_chunk()
and stops exporting the functions below:
o end_that_request_last()
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts scsi mid-layer to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interface of internal function, scsi_end_request(),
is changed.
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds a variant of the interface, blk_end_bidi_request(),
which completes a bidi request.
Bidi request must be completed as a whole, both rq and rq->next_rq
at once. So the interface has 2 arguments for completion size.
As for ->end_io, only rq->end_io is called (rq->next_rq->end_io is not
called). So if special completion handling is needed, the handler
must be set to rq->end_io.
And the handler must take care of freeing next_rq too, since
the interface doesn't care of it if rq->end_io is not NULL.
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts ide-cd (cdrom_newpc_intr()) to use blk_end_request
interfaces. Related 'uptodate' arguments are converted to 'error'.
In PIO mode, ide-cd (cdrom_newpc_intr()) needs to defer
end_that_request_last() until the device clears DRQ_STAT and raises
an interrupt after end_that_request_first().
So blk_end_request() has to return without completing request
even if no leftover in the request.
ide-cd uses blk_end_request_callback() and a dummy callback function,
which just returns value '1', to tell blk_end_request_callback()
about that.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds a variant of the interface, blk_end_request_callback(),
which has driver callback feature.
Drivers may need to do special works between end_that_request_first()
and end_that_request_last().
For such drivers, blk_end_request_callback() allows it to pass
a callback function which is called between end_that_request_first()
and end_that_request_last().
This interface is only for fallback of other blk_end_request interfaces.
Drivers should avoid their tricky behaviors and use other interfaces
as much as possible.
Currently, only one driver, ide-cd, needs this interface.
So this interface should/will be removed, after the driver removes
such tricky behaviors.
o ide-cd (cdrom_newpc_intr())
In PIO mode, cdrom_newpc_intr() needs to defer end_that_request_last()
until the device clears DRQ_STAT and raises an interrupt after
end_that_request_first().
So end_that_request_first() and end_that_request_last() are called
separately in cdrom_newpc_intr().
This means blk_end_request_callback() has to return without
completing request even if no leftover in the request.
To satisfy the requirement, callback function has return value
so that drivers can tell blk_end_request_callback() to return
without completing request.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts "normal" parts of ide to use blk_end_request
interfaces. Related 'uptodate' arguments are converted to 'error'.
The conversion of 'uptodate' to 'error' is done only for the internal
function, __ide_end_request().
ide_end_request() was not changed since it's exported and used
by many ide drivers.
With this patch, blkdev_dequeue_request() in __ide_end_request() is
moved to blk_end_request, since blk_end_request takes care of
dequeueing request like below:
if (!list_empty(&rq->queuelist))
blkdev_dequeue_request(rq);
In the case of ide,
o 'dequeue' variable of __ide_end_request() is 1 only when the request
is still linked to the queue (i.e. rq->queuelist is not empty)
o 'dequeue' variable of __ide_end_request() is 0 only when the request
has already been removed from the queue (i.e. rq->queuelist is empty)
So blk_end_request can handle it correctly although ide always run
thought the code above.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts cpqarray to use blk_end_request interfaces.
Related 'ok' arguments are converted to 'error'.
cpqarray is a little bit different from "normal" drivers.
cpqarray directly calls bio_endio() and disk_stat_add()
when completing request. But those can be replaced with
__end_that_request_first().
After the replacement, request completion procedures of
those drivers become like the following:
o end_that_request_first()
o add_disk_randomness()
o end_that_request_last()
This can be converted to __blk_end_request() by following
the rule (b) mentioned in the patch subject
"[PATCH 01/30] blk_end_request: add new request completion interface".
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Ben Dooks
Daniel Mack
Russell King
Richard Purdie
Robert Schwebel
eric miao
Philipp Zabel
Ian Molton
Dmitry Baryshkov
Jens Axboe
eric miao
James Bottomley
Nikanth Karthikesan
Kiyoshi Ueda