PAL_GET_PSTATE accepts a type argument to return different kinds of
frequency information.
Refer: Intel Itanium®Architecture Software Developer's Manual -
Volume 2: System Architecture, Revision 2.2
(http://developer.intel.com/design/itanium/manuals/245318.htm)
Add the support for type argument and use Instantaneous frequency
in the acpi driver.
Also fix a bug, where in return value of PAL_GET_PSTATE was getting compared
with 'control' bits instead of 'status' bits.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Rev 2.2 of Volume 2 of "Intel Itanium Architecture Software Developer's
Manual" (January 2006) adds a se bit to the Processor State Parameter
fields (pages 2:299). This patch gets the structs back in sync
with the spec.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Rev 2.2 of Volume 2 of "Intel Itanium Architecture Software Developer's
Manual" (January 2006) adds a dp bit to the cache_check and bus_check
fields (pages 2:401-2:404). This patch gets the structs back in sync
with the spec.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Linux maps PAL instructions with an ITR, but uses a DTC for PAL data.
Section 11.10.2.1.3, "Making PAL Procedures Calls in Physical or Virtual
Mode," of the SDM (rev 2.2), says we must therefore make all PAL calls
with PSR.ic = 1 so that Linux can handle any TLB faults.
PAL_CALL_IC_OFF is currently unused, and as long as we use the ITR + DTC
strategy, we can't use it. So remove it. I also removed the code in
ia64_pal_call_static() that conditionally cleared PSR.ic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
PAL_CACHE_READ and PAL_CACHE_WRITE need to be called in physical
mode with stacked registers.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
/proc/pal/*/version_info is a bit confusing. HP firmware, at least,
reports 07.31 instead of 0.7.31. Also, the comment is out of place;
it's an internal detail about the implementation of ia64_pal_version.
Since the 2.2 revision of the SDM still states that PAL_VERSION can
be called in virtual mode, correct the comment to be more accurate.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Linux ia64 port tried to decode the processor family number
to something human-readable, but Intel brandnames don't change
synchronously with updates to the family number. Adopt a more
i386-like approach and just print the family number in decimal.
Add a new field "model name" that uses PAL_BRAND_INFO to find
the official name for the cpu, or on older systems, falls back
to using the well-known codenames (Merced, McKinley, Madison).
Signed-off-by: Tony Luck <tony.luck@intel.com>
gcc3 thinks that a 32-bit field of a u64 type is itself a u64, so
should be printed with "%ld". gcc4 thinks it needs just "%d".
Make both versions happy by avoiding this construct.
Signed-off-by: Tony Luck <tony.luck@intel.com>
IPF SDM 2.2 changes definition of PAL_LOGICAL_TO_PHYSICAL to add
proc_number=-1 to get core/thread mapping info on the running processer.
Based on this change, we had better to update existing core/thread
detection in IA64 kernel correspondingly. The attached patch implements
this change. It simplifies detection code and eliminates potential race
condition. It also runs a bit faster and has better scalability especially
when cores and threads number grows up in one package.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Because PAL spec has changed since 2002, you can goto
http://developer.intel.com/design/itanium/manuals/iiasdmanual.htm to
download new SDM, all PAL calls should be invoked with psr.ic=1, and
it's caller's responsibility to handle possible tlb miss.
Ia64_pal_cache_flush was written according to old spec, it is obsolete,
and this patch has ia64_pal_cache_flush conform to new spec.
Signed-off-by Anthony Xu <anthony.xu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch to support P-state transitions on ia64. This driver is based on ACPI,
and uses the ACPI processor driver interface to find out the P-state support
information for the processor. This driver plugs into generic cpufreq
infrastructure.
Once this driver is loaded successfully, ondemand/userspace governor can be
used to change the CPU frequency dynamically based on load or on request from
userspace process.
Refer :
ACPI specification -
http://www.acpi.info
P-state related PAL calls -
http://developer.intel.com/design/itanium/downloads/24869909.pdf
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Version 3 - rediffed to apply on top of Ashok's hotplug cpu
patch. /proc/cpuinfo output in step with x86.
This is an updated MC/MT identification patch based on the
previous discussions on list.
Add the Multi-core and Multi-threading detection for IPF.
- Add new core and threading related fields in /proc/cpuinfo.
Physical id
Core id
Thread id
Siblings
- setup the cpu_core_map and cpu_sibling_map appropriately
- Handles Hot plug CPU
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Gordon Jin <gordon.jin@intel.com>
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Venkatesh Pallipadi
Russ Anderson
Bjorn Helgaas
Tony Luck
Matthew Wilcox
Zhang, Yanmin
Fenghua Yu
Xu, Anthony
Suresh Siddha
Linus Torvalds