On 15 Jun 2006 03:45:10 +0200, Andi Kleen wrote:
> Anyways I would say that if the BIOS can't get MCFG right then
> it's likely not been validated on that board and shouldn't be used.
According to Petr Vandrovec:
... "What is important (and checked) is address of MMCONFIG reported by MCFG
table... Unfortunately code does not bother with printing that address :-(
"Another problem is that code has hardcoded that MMCONFIG area is 256MB large.
Unfortunately for the code PCI specification allows any power of two between 2MB
and 256MB if vendor knows that such amount of busses (from 2 to 128) will be
sufficient for system. With notebook it is quite possible that not full 8 bits
are implemented for MMCONFIG bus number."
So here is a patch. Unfortunately my system still fails the test because
it doesn't reserve any part of the MMCONFIG area, but this may fix others.
Booted on x86_64, only compiled on i386. x86_64 still remaps the max area
(256MB) even though only 2MB is checked... but 2.6.16 had no check at all
so it is still better.
PCI: reduce size of x86 MMCONFIG reserved area check
1. Print the address of the MMCONFIG area when the test for that area
being reserved fails.
2. Only check if the first 2MB is reserved, as that is the minimum.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This a bit late (yours patch was posted about a year ago), but
a co-worker of spotted part of the code that looks like a memory
leak. Looking at the code it seems that pci_mmcfg_config should
be free-ed if MMCONFIG is above 4GB.
From: Konrad Rzeszutek <konradr@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a PCI device is disabled via pci_disable_device(), it's still
left decoding its BAR resource ranges even though its driver
will have likely released those regions (and may even have
unloaded). pci_enable_device() already explicitly enables
BAR resource decode for the device being enabled. This patch
disables resource decode for the PCI device being disabled,
making it symmetric with the enable call.
I saw this while doing something else, not because of a
problem report. Still, seems to be the correct thing to do.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MSI callouts for altix. Involves a fair amount of code reorg in sn irq.c
code as well as adding some extensions to the altix PCI provider abstaction.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract IA64_FIRST_DEVICE_VECTOR/IA64_LAST_DEVICE_VECTOR since SN platforms
use a subset of the IA64 range. Implement this by making the above macros
global variables which the platform can override in it setup code.
Also add a reserve_irq_vector() routine used by SN to mark a vector's as
in-use when that weren't allocated through assign_irq_vector().
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the changes from an earlier patch that disables
oProfile for iSeries within the oProfile KConfig (submitted Feb 23,
2006). Checks within the arch init for iSeries, still allowing profiling
for timer interrupts (using firmware_has_feature).
Signed-off-by: Kelly Daly <kelly@au.ibm.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support the ibm,extended-*-frequency properties found in recent POWER5
firmware:
cpus/PowerPC,POWER5@0/clock-frequency
59aa5880 (1504336000)
cpus/PowerPC,POWER5@0/ibm,extended-clock-frequency
00000000 59aa5880
cpus/PowerPC,POWER5@0/timebase-frequency
0b354b10 (188042000)
cpus/PowerPC,POWER5@0/ibm,extended-timebase-frequency
00000000 0b354b10
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Don't dereference a device node that isn't there. A "shouldn't
happen" case, but someone ran into it with a possibly misconfigured
device tree.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Looking for class-code in PCI children breaks with direct slots. Lets
just count all children.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Avoid duplication of the syscall table for the cell platform. Based on an
idea from David Woodhouse.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Tue, Jun 20, 2006 at 02:01:26PM +1000, Benjamin Herrenschmidt wrote:
> On Mon, 2006-06-19 at 13:08 -0700, Mark A. Greer wrote:
> > MPC10x-style interrupt controllers have a serial mode that allows
> > several interrupts to be clocked in through one INT signal.
> >
> > This patch adds the software support for that mode.
>
> You hard code the clock ratio... why not add a separate call to be
> called after mpic_init,
> something like mpic_set_serial_int(int mpic, int enable, int
> clock_ratio) ?
How's this?
--
MPC10x-style interrupt controllers have a serial mode that allows
several interrupts to be clocked in through one INT signal.
This patch adds the software support for that mode.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
--
arch/powerpc/sysdev/mpic.c | 20 ++++++++++++++++++++
include/asm-powerpc/mpic.h | 10 ++++++++++
2 files changed, 30 insertions(+)
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PCI error recovery code will printk diagnostic info when
a PCI error event occurs. Change the messages to include the slot
location code, which is how most sysadmins will know the device.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPU context save/restore code is currently built
for a 4k page size and we provide a _shipped version
of it since most people don't have the spu toolchain
that is needed to rebuild that code.
This patch hardcodes the data structures to a 64k
page alignment, which also guarantees 4k alignment
but unfortunately wastes 60k of memory per SPU
context that is created in the running system.
We will follow up on this with another patch to
reduce that overhead or maybe redo the context
save/restore logic to do this part entirely different,
but for now it should make experimental systems
work with either page size.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At this time, all flags are invalid. Since we are
planning to actually add valid flags in the future,
we better check if any were passed by the user.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SPU interrupt status must be cleared before handle it.
Otherwise, kernel may drop some interrupt packet.
Currently, class2 interrupt treated like:
1) call callback to wake up waiting process
2) mask raised mailbox interrupt
3) clear interrupt status
I changed like:
1) mask raised mailbox interrupt
2) clear interrupt status
3) call callback to wake up waiting process
Clearing status before masking will make spurious interrupt.
Thus, it is necessary to hold by steps I described above, I think.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch remove 'stop_code' -- discarded member of struct spu.
It is written at initialize and interrupt, but never read
in current implementation.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the hypervisor abstraction of setting cpu affinity to a
higher level to avoid platform dependent interrupt controller
routines. I replaced spu_priv1_ops:spu_int_route_set() with a
new routine spu_priv1_ops:spu_cpu_affinity_set().
As a by-product, this change eliminated what looked like an
existing bug in the set affinity code where spu_int_route_set()
mistakenly called int_stat_get().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To support muti-platform binaries the spu hypervisor accessor
routines must have runtime binding.
I removed the existing statically linked routines in spu.h
and spu_priv1_mmio.c and created new accessor routines in spu_priv1.h
that operate indirectly through an ops struct spu_priv1_ops.
spu_priv1_mmio.c contains the instance of the accessor routines
for running on raw hardware.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Creates new config variables PPC_CELL_NATIVE and PPC_IBM_CELL_BLADE.
The existing CONFIG_PPC_CELL is now used to denote the generic
Cell processor support.
PPC_CELL = make descends into platforms/cell
PPC_CELL_NATIVE = add bare metal support
PPC_IBM_CELL_BLADE = add blade device drivers, etc.
Also renames spu_priv1.c to spu_priv1_mmio.c.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The save/restore sequence for SPE contexts currently attempts to save
and restore the channel count for SPE channel 1 (the SPU_WriteEventMask
channel. But the CBE architecture (section 9.11.2) clearly states
that this channel does not have an associated count. Hardware simply
ignores the attempt to write this count, but the simulator generates
a warning message.
WARNING: 279721590: SPE7: Attempt to write channel count for CH 1 with
no associated count is ignored.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up create_spu() a little by using kzalloc instead of kmalloc +
assignments.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The wbox channel count of an spu is now initialized
to four for the saved context. This makes it possible
to write to the mailbox right away without waiting
for the SPE to become scheduled first.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For performance analysis, it is often interesting to know
which physical SPE a thread is currently running on, and,
more importantly, if it is running at all.
This patch adds a simple attribute to each SPU directory
with that information.
The attribute is read-only and called 'phys-id'. It contains
an ascii string with the number of the physical SPU (e.g.
"0x5"), or alternatively the string "0xffffffff" (32 bit -1)
when it is not running at all at the time that the file
is read.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spufs currently knows only 4k pages and 16M hugetlb
pages. Make it use the regular methods for deciding on
the SLB bits.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spufs_rmdir tries to acquire the spufs root
i_mutex, which is already held by spufs_create_thread.
This was tracked as Bug #H9512.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A recent change to the way that the mfc file gets mapped made it
impossible to map the SPE Multi-Source Synchronization register
into user space, but that may be needed by some applications.
This restores the missing functionality.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The spu_base module is rather deeply intermixed with the
core kernel, so it makes sense to have that built-in.
This will let us extend the base in the future without
having to export more core symbols just for it.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SPUs are registered as system devices, exposing attributes through
sysfs. Since the sysdev includes a kref, we can remove the one in
struct spu (it isn't used at the moment anyway).
Currently only the interrupt source and numa node attributes are added.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable some of the most requested features in defconfig
and refresh with the latest powerpc.git Kconfig files.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Checking the priority field to test for irq validity is
completely bogus and breaks with future external interrupt
controllers.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a first version of support for the Cell BE "Reliability,
Availability and Serviceability" features.
It doesn't yet handle some of the RAS interrupts (the ones described in
iic_is/iic_irr), I'm still working on a proper way to expose these. They
are essentially a cascaded controller by themselves (sic !) though I may
just handle them locally to the iic driver. I need also to sync with
David Erb on the way he hooked in the performance monitor interrupt.
So that's all for 2.6.17 and I'll do more work on that with my rework of
the powerpc interrupt layer that I'm hacking on at the moment.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clear the high BATS during load_up_mmu if FTR_HAS_HIGH_BATS.
Allow just a bit more time for secondary CPUs to phone home.
Signed-off-by: Wei Zhang <Wei.Zhang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Export both news RTAS delay functions, and change the scanlog module to
use the new delay functions.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.infradead.org/~dwmw2/rbtree-2.6:
[RBTREE] Switch rb_colour() et al to en_US spelling of 'color' for consistency
Update UML kernel/physmem.c to use rb_parent() accessor macro
[RBTREE] Update hrtimers to use rb_parent() accessor macro.
[RBTREE] Add explicit alignment to sizeof(long) for struct rb_node.
[RBTREE] Merge colour and parent fields of struct rb_node.
[RBTREE] Remove dead code in rb_erase()
[RBTREE] Update JFFS2 to use rb_parent() accessor macro.
[RBTREE] Update eventpoll.c to use rb_parent() accessor macro.
[RBTREE] Update key.c to use rb_parent() accessor macro.
[RBTREE] Update ext3 to use rb_parent() accessor macro.
[RBTREE] Change rbtree off-tree marking in I/O schedulers.
[RBTREE] Add accessor macros for colour and parent fields of rb_node
* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
[ARM] 3559/1: S3C2442: core and serial port
[ARM] 3557/1: S3C24XX: centralise and cleanup uart registration
[ARM] 3558/1: SMDK24XX: LED platform devices
[ARM] 3534/1: add spi support to lubbock platform
[ARM] 3554/1: ARM: Fix dyntick locking
[ARM] 3553/1: S3C24XX: earlier print of cpu idcode info
[ARM] 3552/1: S3C24XX: Move VA of GPIO for low-level debug
[ARM] 3551/1: S3C24XX: PM code failes to compile with CONFIG_DCACHE_WRITETHROUGH
[ARM] 3550/1: OSIRIS: fix serial port map for 1:1
[ARM] 3548/1: Fix the ARMv6 CPU id in compressed/head.S
[ARM] 3335/1: Old-abi Thumb sys_syscall broken
[ARM] 3467/1: [3/3] Support for Philips PNX4008 platform: defconfig
[ARM] 3466/1: [2/3] Support for Philips PNX4008 platform: chip support
[ARM] 3465/1: [1/3] Support for Philips PNX4008 platform: headers
[ARM] 3407/1: lpd7x: documetation update
[ARM] 3406/1: lpd7x: compilation fix for smc91x
[ARM] 3405/1: lpd7a40x: CPLD ssp driver
[ARM] 3404/1: lpd7a40x: AMBA CLCD support
[ARM] 3403/1: lpd7a40x: updated default configurations
[ARM] 3402/1: lpd7a40x: serial driver bug fix
...
Patch from Deepak Saxena
This patch makes soft reboot work on the Versatile board. Thanks to
Catalin Marinas @ ARM for pointing out the proper way to do this.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch removes some now unnecessary global variables -
at91_master_clock, at91_serial_map, at91_console_port.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Update s3c2410_defconfig to latest kernel with the
latest patches
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This final patch includes some general fixes.
1. Link in pm.o if CONFIG_PM is enabled. [Should have been included in
patch 3605/1].
2. Use __raw_readl()/__raw_writel() when accessing System Peripheral
registers.
3. Removed some unnecessary includes
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds the core Power Management support for the AT91RM9200
processor. It will support suspend-to-RAM and standby modes.
The suspend-to-RAM functionality is not 100% complete. The code that
needs to be execute from the internal SRAM to restore the system is
outstanding. For now we just fall through to Standby mode.
The AT91-specific at91_suspend_entering_slow_clock() function will
eventually be replaced by clk_must_disable() once that functionality is
added to mainline clock API.
Patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is the long overdue conversion of sparc64 over to
the generic IRQ layer.
The kernel image is slightly larger, but the BSS is ~60K
smaller due to the reduced size of struct ino_bucket.
A lot of IRQ implementation details, including ino_bucket,
were moved out of asm-sparc64/irq.h and are now private to
arch/sparc64/kernel/irq.c, and most of the code in irq.c
totally disappeared.
One thing that's different at the moment is IRQ distribution,
we do it at enable_irq() time. If the cpu mask is ALL then
we round-robin using a global rotating cpu counter, else
we pick the first cpu in the mask to support single cpu
targetting. This is similar to what powerpc's XICS IRQ
support code does.
This works fine on my UP SB1000, and the SMP build goes
fine and runs on that machine, but lots of testing on
different setups is needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired by PowerPC XICS interrupt support code.
All IRQs are virtualized in order to keep NR_IRQS from needing
to be too large. Interrupts on sparc64 are arbitrary 11-bit
values, but we don't need to define NR_IRQS to 2048 if we
virtualize the IRQs.
As PCI and SBUS controller drivers build device IRQs, we divy
out virtual IRQ numbers incrementally starting at 1. Zero is
a special virtual IRQ used for the timer interrupt.
So device drivers all see virtual IRQs, and all the normal
interfaces such as request_irq(), enable_irq(), etc. translate
that into a real IRQ number in order to configure the IRQ.
At this point knowledge of the struct ino_bucket is almost
entirely contained within arch/sparc64/kernel/irq.c There are
a few small bits in the PCI controller drivers that need to
be swept away before we can remove ino_bucket's definition
out of asm-sparc64/irq.h and privately into kernel/irq.c
Signed-off-by: David S. Miller <davem@davemloft.net>
And reuse that struct member for virt_irq, which will
be used in future changesets for the implementation of
mapping between real and virtual IRQ numbers.
This nicely kills off a ton of SBUS and PCI controller
PIL assignment code which is no longer necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only pil0_dummy_bucket had a pil of zero and we just killed that
off, so we can delete all special case code that used bp->pil==0
as a way to identify a dummy bucket.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first in a series of cleanups that will hopefully
allow a seamless attempt at using the generic IRQ handling
infrastructure in the Linux kernel.
Define PIL_DEVICE_IRQ and vector all device interrupts through
there.
Get rid of the ugly pil0_dummy_{bucket,desc}, instead vector
the timer interrupt directly to a specific handler since the
timer interrupt is the only event that will be signaled on
PIL 14.
The irq_worklist is now in the per-cpu trap_block[].
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the calculation of the end address when flushing iotlb entries to
ram. This bug has been a cause of esp dma errors, and it affects
HyperSPARC systems much worse than SuperSPARC systems.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the smp related section mismatch warnings by marking the smp init
functions as cpuinit.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup cpu_possible_map so the secondary cpus will get started.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a crash in SMP mode by adding the missing topology_init.
Also makes /proc/cpuinfo backwards compatible with 2.4.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fid/vid masks for parts using the extended parts are slightly incorrect and can result in
incorrect fid/vid codes being applied. No instances of this problem have been reported in
the field but it could be a problem with future parts.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch clarifies the meaning of the cpu_family if
statements in the hw pstate driver patch for powernow-k8
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (51 commits)
[MIPS] Make timer interrupt frequency configurable from kconfig.
[MIPS] Correct HAL2 Kconfig description
[MIPS] Fix R4K cache macro names
[MIPS] Add Missing R4K Cache Macros to IP27 & IP32
[MIPS] Support for the RM9000-based Basler eXcite smart camera platform.
[MIPS] Support for the R5500-based NEC EMMA2RH Mark-eins board
[MIPS] Support SNI RM200C SNI in big endian mode and R5000 processors.
[MIPS] SN: include asm/sn/types.h for nasid_t.
[MIPS] Random fixes for sb1250
[MIPS] Fix bcm1480 compile
[MIPS] Remove support for NEC DDB5476.
[MIPS] Remove support for NEC DDB5074.
[MIPS] Cleanup memory managment initialization.
[MIPS] SN: Declare bridge_pci_ops.
[MIPS] Remove unused function alloc_pci_controller.
[MIPS] IP27: Extract pci_ops into separate file.
[MIPS] IP27: Use symbolic constants instead of magic numbers.
[MIPS] vr41xx: remove unnecessay items from vr41xx/Kconfig.
[MIPS] IP27: Cleanup N/M mode configuration.
[MIPS] IP27: Throw away old unused hacks.
...
Patch from Richard Purdie
Poodle Updates:
* Update corgi_ssp to make the GPIO chip selects optional
* Enable corgi_ssp for use by poodle
* Add corgi touchscreen platform device for poodle
* Export locomo platform device.
* Set framebuffer device parent correctly
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Abstract some machine specific parameters from the sharpsl_pm core
into the machine specific drivers. This allows the core to support
tosa/poodle.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Correct the Poodle power control for the MMC/SD port. Also
add write protection switch support.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add functionality to allow machine specific reboot handlers on ARM.
Add machine specific reboot and poweroff handlers for all PXA Zaurus
models.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Platform device definitions for the two IDE ports
on the Simtec Anubis board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch updates the support for the Atmel DK and EK boards.
The changes include:
1. Use the new at91_uart_config structure and device registration
functions for the UARTs.
2. Registration of I2C and SPI platform devices.
3. The USB Device pullup line is connected to reset, so multidrive needs
to be enabled on the line. [Patch from David Brownell].
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make HZ configurable. DECSTATION can select 128/256/1024 HZ, JAZZ can
only select 100 HZ, others can select 100/128/250/256/1000/1024 HZ if
not explicitly specified). Also remove all mach-xxx/param.h files and
update all defconfigs according to current HZ value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Added support for RM200C machines with big endian firmware
Added support for RM200-C40 (R5000 support)
Signed-off-by: Florian Lohoff <flo@rfc822.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Random improvements for sb1250: Silence compiler warnings, a bugfix for
the profiling code, and a comment typo.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix compilation for bcm1480, a hpt is only available on sb1250/bcm112x.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Historically plat_mem_setup did the entire platform initialization. This
was rather impractical because it meant plat_mem_setup had to get away
without any kind of memory allocator. To keep old code from breaking
plat_setup was just renamed to plat_setup and a second platform
initialization hook for anything else was introduced.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove unnecessary items from vr41xx/Kconfig. SYS_HA_CPU_VR41XX has
already been selected by MACH_VR41XX.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IP27 configuration isn't the only NUMA system - it just happens to be
the currently only supported MIPS NUMA system. So move the necessary
options back into the main MIPS Kconfig file.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mark au1xxx_timer_setup() __init, just because it is. Get rid of
unneeded extern's (note that (*do_gettimeoffset)() is already declared by
<asm/time.c>) and an unused variable. Kill some whitespace...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Chuck Ebbert
Konrad Rzeszutek
Greg Kroah-Hartman
Rajesh Shah
Mark Maule
Kelly Daly
Anton Blanchard
Nathan Lynch
Andreas Schwab
Mark A. Greer
Linas Vepstas
arnd@arndb.de
Masato Noguchi
Geoff Levand
Jeremy Kerr
Michael Ellerman
Benjamin Herrenschmidt
Jon Loeliger
John Rose
Linus Torvalds
Russell King
Deepak Saxena
Andrew Victor
Ben Dooks
David S. Miller
David S. Miller
Bob Breuer
Langsdorf, Mark
Richard Purdie
Atsushi Nemoto
Ralf Baechle
dmitry pervushin
Thomas Bogendoerfer
Thiemo Seufer
Yoichi Yuasa
Rodolfo Giometti
Sergei Shtylyov