This is a reimplementation of the zs driver for the serial subsystem. Any
resemblance to the old driver is purely coincidential. ;-) I do hope I got
the handling of modem lines right -- better do not tackle me about the
issue unless you feel too good...
Any users of the old driver: please note the numbers of the serial lines
have now been swapped, i.e. ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3. It has
to do with the modem lines mentioned above; basically the port A in a given
chip has to be initialised before the port B if you want to use the latter
as the serial console (which is usually the case), as operations on modem
lines of the serial line associated with the port B access both ports (see
the comment at the top of the driver for the details of wiring used).
Please update your scripts.
This is also the reason each SCC now requests an IRQ once only (as seen in
"/proc/interrupts") -- the handler takes care of both ports at once as the
line associated with the port B has to take status update interrupts from
both ports (and yet the line of the port A takes its own for itself too).
The old driver never got it right...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
early_serial_setup was removed from serial.h, but forgot to put in
serial_8250.h
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the SB1250 DUART, a dual serial port implementation
included in the Broadcom family of SOCs descending from the SiByte SB1250
MIPS64 chip multiprocessor. It is a new implementation replacing the
old-fashioned driver currently present in the linux-mips.org tree. It
supports all the usual features one would expect from a(n asynchronous)
serial driver, including modem line control (as far as hardware supports it
-- there is edge detection logic missing from the DCD and RI lines and the
driver does not implement polling of these lines at the moment), the serial
console, BREAK transmission and reception, including the magic SysRq. The
receive FIFO threshold is not maintained though.
The driver was tested with a SWARM board which uses a BCM1250 SOC (which is
dual MIPS64 CMP) and has both ports of the single DUART implemented wired
externally. Both were tested. Testing included using the ports as
terminal lines at 1200bps (which is the ports minimum), 115200bps and a
couple of random speeds inbetween. The modem lines were verified to
operate correctly. No testing was performed with a use as a network
interface, like with SLIP or PPP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (209 commits)
[POWERPC] Create add_rtc() function to enable the RTC CMOS driver
[POWERPC] Add H_ILLAN_ATTRIBUTES hcall number
[POWERPC] xilinxfb: Parameterize xilinxfb platform device registration
[POWERPC] Oprofile support for Power 5++
[POWERPC] Enable arbitary speed tty ioctls and split input/output speed
[POWERPC] Make drivers/char/hvc_console.c:khvcd() static
[POWERPC] Remove dead code for preventing pread() and pwrite() calls
[POWERPC] Remove unnecessary #undef printk from prom.c
[POWERPC] Fix typo in Ebony default DTS
[POWERPC] Check for NULL ppc_md.init_IRQ() before calling
[POWERPC] Remove extra return statement
[POWERPC] pasemi: Don't auto-select CONFIG_EMBEDDED
[POWERPC] pasemi: Rename platform
[POWERPC] arch/powerpc/kernel/sysfs.c: Move NUMA exports
[POWERPC] Add __read_mostly support for powerpc
[POWERPC] Modify sched_clock() to make CONFIG_PRINTK_TIME more sane
[POWERPC] Create a dummy zImage if no valid platform has been selected
[POWERPC] PS3: Bootwrapper support.
[POWERPC] powermac i2c: Use mutex
[POWERPC] Schedule removal of arch/ppc
...
Fixed up conflicts manually in:
Documentation/feature-removal-schedule.txt
arch/powerpc/kernel/pci_32.c
arch/powerpc/kernel/pci_64.c
include/asm-powerpc/pci.h
and asked the powerpc people to double-check the result..
Mixing putchar() and write() hvcalls does not work %100
correctly. But we should be using write() all the time
if we can, even from ->start_tx(), anyways.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (26 commits)
[SPARC64]: Fix UP build.
[SPARC64]: dr-cpu unconfigure support.
[SERIAL]: Fix console write locking in sparc drivers.
[SPARC64]: Give more accurate errors in dr_cpu_configure().
[SPARC64]: Clear cpu_{core,sibling}_map[] in smp_fill_in_sib_core_maps()
[SPARC64]: Fix leak when DR added cpu does not bootup.
[SPARC64]: Add ->set_affinity IRQ handlers.
[SPARC64]: Process dr-cpu events in a kthread instead of workqueue.
[SPARC64]: More sensible udelay implementation.
[SPARC64]: SMP build fixes.
[SPARC64]: mdesc.c needs linux/mm.h
[SPARC64]: Fix build regressions added by dr-cpu changes.
[SPARC64]: Unconditionally register vio_bus_type.
[SPARC64]: Initial LDOM cpu hotplug support.
[SPARC64]: Fix setting of variables in LDOM guest.
[SPARC64]: Fix MD property lifetime bugs.
[SPARC64]: Abstract out mdesc accesses for better MD update handling.
[SPARC64]: Use more mearningful names for IRQ registry.
[SPARC64]: Initial domain-services driver.
[SPARC64]: Export powerd facilities for external entities.
...
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (68 commits)
sh: sh-rtc support for SH7709.
sh: Revert __xdiv64_32 size change.
sh: Update r7785rp defconfig.
sh: Export div symbols for GCC 4.2 and ST GCC.
sh: fix race in parallel out-of-tree build
sh: Kill off dead mach.c for hp6xx.
sh: hd64461.h cleanup and added comments.
sh: Update the alignment when 4K stacks are used.
sh: Add a .bss.page_aligned section for 4K stacks.
sh: Don't let SH-4A clobber SH-4 CFLAGS.
sh: Add parport stub for SuperIO ports.
sh: Drop -Wa,-dsp for DSP tuning.
sh: Update dreamcast defconfig.
fb: pvr2fb: A few more __devinit annotations for PCI.
fb: pvr2fb: Fix up section mismatch warnings.
sh: Select IPR-IRQ for SH7091.
sh: Correct __xdiv64_32/div64_32 return value size.
sh: Fix timer-tmu build for SH-3.
sh: Add cpu and mach links to CLEAN_FILES.
sh: Preliminary support for the SH-X3 CPU.
...
Do not mark sn_sal_console_setup as __init since it's referenced from
non init data structures.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RXBRK field in the AT91/AT32 USART status register has the
following definition according to e.g. the AT32AP7000 data sheet:
RXBRK: Break Received/End of Break
0: No Break received or End of Break detected since the last RSTSTA.
1: Break Received or End of Break detected since the last RSTSTA.
Thus, for each break, the USART sets the RXBRK bit twice. This patch
modifies the driver to report the break event to the serial core only
once by keeping track of whether a break condition is currently
active. The break_active flag is reset as soon as a character is
received, so even if we miss the start-of-break interrupt this should
do the right thing.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ivan Kuten <ivan.kuten@promwad.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@rfo.atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Beacuse SERIAL_PORT_DFNS is removed from include/asm-i386/serial.h and
include/asm-x86_64/serial.h. the serial8250_ports need to be probed late in
serial initializing stage. the console_init=>serial8250_console_init=>
register_console=>serial8250_console_setup will return -ENDEV, and console
ttyS0 can not be enabled at that time. need to wait till uart_add_one_port in
drivers/serial/serial_core.c to call register_console to get console ttyS0.
that is too late.
Make early_uart to use early_param, so uart console can be used earlier. Make
it to be bootconsole with CON_BOOT flag, so can use console handover feature.
and it will switch to corresponding normal serial console automatically.
new command line will be:
console=uart8250,io,0x3f8,9600n8
console=uart8250,mmio,0xff5e0000,115200n8
or
earlycon=uart8250,io,0x3f8,9600n8
earlycon=uart8250,mmio,0xff5e0000,115200n8
it will print in very early stage:
Early serial console at I/O port 0x3f8 (options '9600n8')
console [uart0] enabled
later for console it will print:
console handover: boot [uart0] -> real [ttyS0]
Signed-off-by: <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some RS-232 devices require DTR to be asserted before they can be used. DTR
is normally asserted in uart_startup() when the port is opened. But we don't
actually open serial console ports, so assert DTR when the port is added.
BTW:
earlyprintk and early_uart are hard coded to set DTR/RTS.
rmk says
The only issue I can think of is the possibility for an attached modem to
auto-answer or maybe even auto-dial before the system is ready for it to do
so. Might have an undesirable cost implication for some running with such a
setup.
Apart from that, I can't think of any other side effect of this specific
patch.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mirror the logic in 8250 for proper console write locking
when SYSRQ is triggered or an OOPS is in progress.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Rename PC speaker code
[MIPS] Don't use genrtc.
[MIPS] Remove unused time.c for swarm
[MIPS] Sparse: Use NULL for pointer
[MIPS] Fix a sparse warning in arch/mips/pci/pci.c
[MIPS] SMTC: Interrupt mask backstop hack
[MIPS] separate platform_device registration for VR41xx RTC
[MIPS] Separate platform_device registration for VR41xx GPIO
[MIPS] MIPSsim: Fix build.
[MIPS] separate platform_device registration for VR41xx serial interface
[MIPS] Include cacheflush.h in uncache.c
[MIPS] Cleanup tlbdebug.h
[MIPS] Change names of local variables to silence sparse (part 2)
[MIPS] Workaround for a sparse warning in include/asm-mips/io.h
[MIPS] RM: Use only phyiscal address for 82596 and 53c710
[MIPS] Hydrogen3: Remove remaining bits of code.
[MIPS] DEC: Fix modpost warning.
Revert "[MIPS] DEC: Fix modpost warning."
[MIPS] Fix resume for 64K page size on R4000 class processors.
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, of_serial driver supports only 8250 compatible ports, but
prepares that others can easily be added. Yet unregister routine
assumes port is 8250. This corrects unregister routine to check
port type.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current of_serial driver assumes unknown serial port to be 8250. But
this behavior may cause fatal problems when the serial port is not
8250. This corrects probe routine to ignore unknown serial port.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The interrupt clearing code in mpsc_sdma_intr_ack() mistakenly clears the
interrupt for both controllers instead of just the one its supposed to.
This can result in the other controller appearing to hang because its
interrupt was effectively lost.
So, don't clear the interrupt cause bits for both MPSC controllers when
clearing the interrupt for one of them. Just clear the one that is
supposed to be cleared.
Signed-off-by: Jay Lubomirski <jaylubo@motorola.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
as the termios info does not stipulate that the former are dependent on the latter
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
if we get a break signal, we want to ignore framing and parity errors
because those will always be set (by nature of the signal)
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Now that select no longer works for selecting the "closest" CPU,
we have to explicitly reference the precise sub-type in the few
places where it actually matters (presently only setup code and
some legacy sh-sci cruft).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The -rt patch triggered a lockdep warning in the amba serial drivers, which never
shows up on UP kernels. On SMP systems this would trigger as well.
Release the port lock before calling tty_flip_buffer_push() and reacquire it after
the call. This matches the code in the 8250 serial driver.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a error reported by newer versions of GCC.
error: static declaration of 'ks8695_reg' follows non-static declaration
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Linux kernel ignored the PROM's serial settings (115200,n,8,1 in
my case). This was because mode_prop remained "ttyX-mode" (expected:
"ttya-mode") due to the constness of string literals when used with
"char *". Since there is no "ttyX-mode" property in the PROM, Linux
always used the default 9600.
[ Investigation of the suncore.s assembler reveals that gcc optimizied
away the stores, yet did not emit a warning, which is a pretty
anti-social thing to do and is the only reason this bug lived for
so long -DaveM ]
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes section mismatch warnings in the sunzilog driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
properly setting up and respecting the read_status_mask / ignore_status_mask fields of the serial core
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After a suspend/resume cycle, the UART may have been reset into
low-speed mode -- either because it's actually been reset, or because
the firmware pokes at the old-style divisor registers. If we detected it
as a NS16550A SuperIO chip in the first place and set baud_base to
921600, then we should do so again in the resume path.
This patch adds that code to serial8250_resume_port(), and also makes
serial8250_resume() actually call serial8250_resume_port() for each port
instead of just calling uart_resume_port() directly. And thus fixes
serial port operation after suspend/resume.
It also fixes a bogus comment where we write the EXCR2 register with a
comment saying /* EXCR1 */
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch add new sub-device-id to support new adapter and changed the
interrupt irq number for unsigned char to unsigned int.
[akpm@osdl.org: fix whitespace in device table]
Signed-off by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A fix for a really stupid typo in the KS8695 serial driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hypervisor interfaces need to be negotiated in order to use
some API calls reliably. So add a small set of interfaces
to request API versions and query current settings.
This allows us to fix some bugs in the hypervisor console:
1) If we can negotiate API group CORE of at least major 1
minor 1 we can use con_read and con_write which can improve
console performance quite a bit.
2) When we do a console write request, we should hold the
spinlock around the whole request, not a byte at a time.
What would happen is that it's easy for output from
different cpus to get mixed with each other.
3) Use consistent udelay() based polling, udelay(1) each
loop with a limit of 1000 polls to handle stuck hypervisor
console.
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver for the KS8695 internal UART.
Based on the 2.6.9 driver from Micrel.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add devres ecardm_iomap() and ecardm_iounmap() for Acorn expansion
cards. Convert all expansion card drivers to use them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (24 commits)
[POWERPC] Fix compile error with kexec and CONFIG_SMP=n
[POWERPC] Split initrd logic out of early_init_dt_scan_chosen() to fix warning
[POWERPC] Fix warning in hpte_decode(), and generalize it
[POWERPC] Minor pSeries IOMMU debug cleanup
[POWERPC] PS3: Fix sys manager build error
[POWERPC] Assorted janitorial EEH cleanups
[POWERPC] We don't define CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
[POWERPC] pmu_sys_suspended is only defined for PPC32
[POWERPC] Fix incorrect calculation of I/O window addresses
[POWERPC] celleb: Update celleb_defconfig
[POWERPC] celleb: Fix parsing of machine type hack command line option
[POWERPC] celleb: Fix PCI config space accesses to subordinate buses
[POWERPC] celleb: Fix support for multiple PCI domains
[POWERPC] Wire up sys_utimensat
[POWERPC] CPM_UART: Removed __init from cpm_uart_init_portdesc to fix warning
[POWERPC] User rheap from arch/powerpc/lib
[POWERPC] 83xx: Fix the PCI ranges in the MPC834x_MDS device tree.
[POWERPC] 83xx: Fix the PCI ranges in the MPC832x_MDS device tree.
[POWERPC] CPM_UART: cpm_uart_set_termios should take ktermios, not termios
[POWERPC] Change rheap functions to use ulongs instead of pointers
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Use alloc_pci_dev() in PCI bus probes.
[SPARC64]: Bump PROMINTR_MAX to 32.
[SPARC64]: Fix recursion in PROM tree building.
[SERIAL] sunzilog: Interrupt enable before ISR handler installed
[SPARC64] PCI: Consolidate PCI access code into pci_common.c
Maciej W. Rozycki
Yinghai Lu
Linus Torvalds
David S. Miller
Jes Sorensen
Alan Cox
Haavard Skinnemoen
Thiemo Seufer
Yoichi Yuasa
Roy Huang
Auke Kok
Paul Mackerras
Ishizaki Kou
Kumar Gala
Komuro
Jay Lubomirski
Sonic Zhang
Paul Mundt
Mike Frysinger
Russell King
Thomas Gleixner
Andrew Victor
Jan Engelhardt
Krzysztof Helt
Aubrey Li
David Woodhouse
wendy xiong