Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh775x hardware
blocks such as SCI/SCIF/RTC/DMAC/TMU2/REF.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.
This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes interrupt priority tables from the intc code.
Optimal priority assignment varies with embedded application anyway,
so keeping the interrupt priority tables together with cpu-specific
code doesn't make sense.
The function intc_set_priority() should be used instead to set the
desired interrupt priority level.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the intc core improved it is now possible to put the intc data
structures in the initdata section.
Version two of this patch puts the __initdata inside DECLARE_INTC_DESC()
and removes the __initdata included in the board specific r2d code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We need a secondary register member in struct intc_prio_reg to support
dual priority registers used by ipi on x3.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes redundant board specific interrupt code for boards
using sh775x processors and 4 IRQ lines in "Individual Interrupt Mode"
aka IRLM.
Three boards are affected: sh03, snapgear and titan.
The right way to do this is to use cpu specific code provided by intc.
A nice side effect is that sh03 now compiles, board not BROKEN any more.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific 7750 setup code to use the
new intc controller. Many new vectors are added and multiple
processor variants including 7091, 7750, 7750s, 7750r, 7751 and
7751r should all have the correct vectors hooked up.
IRLM interrupts can be enabled using ipr_irq_enable_irlm() which
now is marked as __init.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch unifies the cpu specific interrupt setup functions for
interrupt controller blocks such as ipr, intc2 and intc. There is no
point in having separate functions for each interrupt controller, so
let's clean this up.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the ipr code by grouping the offset array together
with the ipr_data structure in a new data structure called ipr_desc.
This new structure also contains the name of the controller in struct
irq_chip. The idea behind putting struct irq_chip in there is that we
can use offsetof() to locate the base addresses in the irq_chip
callbacks. This strategy has much in common with the recently merged
intc2 code.
One logic change has been made - the original ipr code enabled the
interrupts by default but with this patch they are all disabled by
default.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- setup-sh7750.c only defines the sh7751_ipr_map when building
with SH7751 support.
- 7722 Solution Engine was missing a mach-type entry, causing
the macro in cf-enabler to be undefined.
- arch/sh/mm/init.c needs linux/pagemap.h.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tidies up some of the rts7751r2d mess and gets it booting
again. Update the defconfig, too.
Signed-off-by: Masayuki Hosokawa <hosokawa@ace-jp.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch does the following:
- remove the make_ipr_irq stuff from dma-sh.c and replace it
with a simple channel<->irq mapping table.
- add DMTEx_IRQ constants for sh4 cpus
- fix sh7751 DMAE irq number
The SH7780 uses the same IRQs for DMA as other SH4 types, so
I put the constants on top of the dma.h file.
Other CPU types need to #define their own DMTEx_IRQ contants
in their appropriate header.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Register the RTC resources for the sh775x subtype so that the new
generic RTC support in drivers/rtc/rtc-sh.c will work.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The following moves the creation of IPR interupts into setup-7750.c
and updates a few other things to make it all work after the "Drop
CPU subtype IRQ headers" commit. It boots and runs fine on my titan
board.
- adds an ipr_idx to the ipr_data and uses a function in the subtype
code to calculate the address of the IPR registers
- adds a function to enable individual interrupt mode for externals
in the subtype code and calls that from the titan board code
instead of doing it directly.
- I changed the shift in the ipr_data to be the actual # of bits to
shift, instead of the numnber / 4 - made it easier to match with
the manual.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some simple setup code for most of the CPU subtypes,
primarily simple platform device registration.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm
Paul Mundt
Manuel Lauss
Jamie Lenehan