By default, tun.c running in TUN_TUN_DEV mode will set the protocol of
packet to IPv4 if TUN_NO_PI is set. My program failed to work when I
assumed that the driver will check the first nibble of packet,
determine IP version and set the appropriate protocol.
Signed-off-by: Ang Way Chuang <wcang@nav6.org>
Acked-by: Max Krasnyansky <maxk@qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atl1 driver tries to determine the MAC address thusly:
- If an EEPROM exists, read the MAC address from EEPROM and
validate it.
- If an EEPROM doesn't exist, try to read a MAC address from
SPI flash.
- If that fails, try to read a MAC address directly from the
MAC Station Address register.
- If that fails, assign a random MAC address provided by the
kernel.
We now have a report of a system fitted with an EEPROM containing all
zeros where we expect the MAC address to be, and we currently handle
this as an error condition. Turns out, on this system the BIOS writes
a valid MAC address to the NIC's MAC Station Address register, but we
never try to read it because we return an error when we find the all-
zeros address in EEPROM.
This patch relaxes the error check and continues looking for a MAC
address even if it finds an illegal one in EEPROM.
Signed-off-by: Radu Cristescu <advantis@gmx.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Keep enc28j60 chips in low-power mode when they're not in use.
At typically 120 mA, these chips run hot even when idle; this
low power mode cuts that power usage by a factor of around 100.
This version provides a generic routine to poll a register until
its masked value equals some value ... e.g. bit set or cleared.
It's basically what the previous wait_phy_ready() did, but this
version is generalized to support the handshaking needed to
enter and exit low power mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Minor bugfixes to the enc28j60 driver ... wrong section marking,
indentation, and bogus use of spi_bus_type.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.
Also reduced delays in firmware load.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
management function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Store physical port number in netxen_adapter structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes a the issue where logical port number is set incorrectly
for HP blade mezz cards.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ibm_newemac driver requires ether_crc to be defined. Apparently it is
possible to generate a .config without CONFIG_CRC32 set which causes the
following link errors if IBM_NEW_EMAC is selected:
LD .tmp_vmlinux1
drivers/built-in.o: In function `emac_hash_mc':
core.c:(.text+0x2f524): undefined reference to `crc32_le'
core.c:(.text+0x2f528): undefined reference to `bitrev32'
make: *** [.tmp_vmlinux1] Error 1
This patch has IBM_NEW_EMAC select CRC32 so we don't hit this error.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use max not min to enforce a lower limit on the max I/O size.
This bug was introduced by "fuse: fix max i/o size calculation" (commit
e5d9a0df07).
Thanks to Brian Wang for noticing.
Reported-by: Brian Wang <ywang221@hotmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Acked-by: Szabolcs Szakacsits <szaka@ntfs-3g.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added !vmlinux.lds.h to .gitignore because it would otherwise be ignored.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most users by far do not care about the exact return value (they only
really care about whether the copy succeeded in its entirety or not),
but a few special core routines actually care deeply about exactly how
many bytes were copied from user space.
And the unrolled versions of the x86-64 user copy routines would
sometimes report that it had copied more bytes than it actually had.
Very few uses actually have partial copies to begin with, but to make
this bug even harder to trigger, most x86 CPU's use the "rep string"
instructions for normal user copies, and that version didn't have this
issue.
To make it even harder to hit, the one user of this that really cared
about the return value (and used the uncached version of the copy that
doesn't use the "rep string" instructions) was the generic write
routine, which pre-populated its source, once more hiding the problem by
avoiding the exception case that triggers the bug.
In other words, very special thanks to Bron Gondwana who not only
triggered this, but created a test-program to show it, and bisected the
behavior down to commit 08291429cf ("mm:
fix pagecache write deadlocks") which changed the access pattern just
enough that you can now trigger it with 'writev()' with multiple
iovec's.
That commit itself was not the cause of the bug, it just allowed all the
stars to align just right that you could trigger the problem.
[ Side note: this is just the minimal fix to make the copy routines
(with __copy_from_user_inatomic_nocache as the particular version that
was involved in showing this) have the right return values.
We really should improve on the exceptional case further - to make the
copy do a byte-accurate copy up to the exact page limit that causes it
to fail. As it is, the callers have to do extra work to handle the
limit case gracefully. ]
Reported-by: Bron Gondwana <brong@fastmail.fm>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(which didn't have this problem), and since
most users that do the carethis was very hard to trigger, but
When generating the ip header for the transformed packet we just copy
the frag_off field of the ip header from the original packet to the ip
header of the new generated packet. If we receive a packet as a chain
of fragments, all but the last of the new generated packets have the
IP_MF flag set. We have to mask the frag_off field to only keep the
IP_DF flag from the original packet. This got lost with git commit
36cf9acf93 ("[IPSEC]: Separate
inner/outer mode processing on output")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The H.245 helper is not registered/unregistered, but assigned to
connections manually from the Q.931 helper. This means on unload
existing expectations and connections using the helper are not
cleaned up, leading to the following oops on module unload:
CPU 0 Unable to handle kernel paging request at virtual address c00a6828, epc == 802224dc, ra == 801d4e7c
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000000 00000004 c00a67f0
$ 4 : 802a5ad0 81657e00 00000000 00000000
$ 8 : 00000008 801461c8 00000000 80570050
$12 : 819b0280 819b04b0 00000006 00000000
$16 : 802a5a60 80000000 80b46000 80321010
$20 : 00000000 00000004 802a5ad0 00000001
$24 : 00000000 802257a8
$28 : 802a4000 802a59e8 00000004 801d4e7c
Hi : 0000000b
Lo : 00506320
epc : 802224dc ip_conntrack_help+0x38/0x74 Tainted: P
ra : 801d4e7c nf_iterate+0xbc/0x130
Status: 1000f403 KERNEL EXL IE
Cause : 00800008
BadVA : c00a6828
PrId : 00019374
Modules linked in: ip_nat_pptp ip_conntrack_pptp ath_pktlog wlan_acl wlan_wep wlan_tkip wlan_ccmp wlan_xauth ath_pci ath_dev ath_dfs ath_rate_atheros wlan ath_hal ip_nat_tftp ip_conntrack_tftp ip_nat_ftp ip_conntrack_ftp pppoe ppp_async ppp_deflate ppp_mppe pppox ppp_generic slhc
Process swapper (pid: 0, threadinfo=802a4000, task=802a6000)
Stack : 801e7d98 00000004 802a5a60 80000000 801d4e7c 801d4e7c 802a5ad0 00000004
00000000 00000000 801e7d98 00000000 00000004 802a5ad0 00000000 00000010
801e7d98 80b46000 802a5a60 80320000 80000000 801d4f8c 802a5b00 00000002
80063834 00000000 80b46000 802a5a60 801e7d98 80000000 802ba854 00000000
81a02180 80b7e260 81a021b0 819b0000 819b0000 80570056 00000000 00000001
...
Call Trace:
[<801e7d98>] ip_finish_output+0x0/0x23c
[<801d4e7c>] nf_iterate+0xbc/0x130
[<801d4e7c>] nf_iterate+0xbc/0x130
[<801e7d98>] ip_finish_output+0x0/0x23c
[<801e7d98>] ip_finish_output+0x0/0x23c
[<801d4f8c>] nf_hook_slow+0x9c/0x1a4
One way to fix this would be to split helper cleanup from the unregistration
function and invoke it for the H.245 helper, but since ctnetlink needs to be
able to find the helper for synchonization purposes, a better fix is to
register it normally and make sure its not assigned to connections during
helper lookup. The missing l3num initialization is enough for this, this
patch changes it to use AF_UNSPEC to make it more explicit though.
Reported-by: liannan <liannan@twsz.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly free h323_buffer when helper registration fails.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix three ct_extend/NAT extension related races:
- When cleaning up the extension area and removing it from the bysource hash,
the nat->ct pointer must not be set to NULL since it may still be used in
a RCU read side
- When replacing a NAT extension area in the bysource hash, the nat->ct
pointer must be assigned before performing the replacement
- When reallocating extension storage in ct_extend, the old memory must
not be freed immediately since it may still be used by a RCU read side
Possibly fixes https://bugzilla.redhat.com/show_bug.cgi?id=449315
and/or http://bugzilla.kernel.org/show_bug.cgi?id=10875
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To get this driver working we need the CFLAGS_hpwdt.o += -O in the Makefile.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The driver needs the asmlinkage tag and the CFLAGS line in the Makefile.
Without it the driver doesn't work.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some boxes the touchpad needs to be reinitialized after resume to make
it function again. This fixes bugzilla #10825.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are systems that fail in i8042_resume() with
i8042: Can't write CTR to resume
as i8042_command(&i8042_ctr, I8042_CMD_CTL_WCTR) fails even though the
controller claimed itself to be ready before.
One retry after failing write fixes the problems on the failing systems.
Reported-by: Helmut Schaa <hschaa@novell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix this warning, which appears with !CONFIG_SMP:
kernel/sched.c:1216: warning: `init_hrtick' defined but not used
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This causes the suni driver to oops if you try to use sonetdiag to get
the statistics. Also add the corresponding phy->stop call to fix another
oops if you try to remove the module.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
It happens that if a packet arrives in a VC between the call to open it on
the hardware and the call to change the backend to br2684, br2684_regvcc
processes the packet and oopses dereferencing skb->dev because it is
NULL before the call to br2684_push().
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
1) Remove ICMP_MIN_LENGTH, as it is unused.
2) Remove unneeded tcp_v4_send_check() declaration.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I just noticed "cat /proc/net/raw" was buggy, missing '\n' separators.
I believe this was introduced by commit 8cd850efa4
([RAW]: Cleanup IPv4 raw_seq_show.)
This trivial patch restores correct behavior, and applies to current
Linus tree (should also be applied to stable tree as well.)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Selected device feature bits can be propagated to VLAN devices, so we
can make use of TX checksum offload and TSO on VLAN-tagged packets.
However, if the physical device does not do VLAN tag insertion or
generic checksum offload then the test for TX checksum offload in
dev_queue_xmit() will see a protocol of htons(ETH_P_8021Q) and yield
false.
This splits the checksum offload test into two functions:
- can_checksum_protocol() tests a given protocol against a feature bitmask
- dev_can_checksum() first tests the skb protocol against the device
features; if that fails and the protocol is htons(ETH_P_8021Q) then
it tests the encapsulated protocol against the effective device
features for VLANs
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, any time we set a primary transport we set
the changeover_active flag. As a result, we invoke SFR-CACC
even when there has been no changeover events.
Only set changeover_active, when there is a true changeover
event, i.e. we had a primary path and we are changing to
another transport.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove the proc fs entry which has been created if fail to
set up proc fs entry for the SCTP protocol.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingo's system is still seeing strange behavior, and he
reports that is goes away if the rest of the deferred
accept changes are reverted too.
Therefore this reverts e4c7884028
("[TCP]: TCP_DEFER_ACCEPT updates - dont retxmt synack") and
539fae89be ("[TCP]: TCP_DEFER_ACCEPT
updates - defer timeout conflicts with max_thresh").
Just like the other revert, these ideas can be revisited for
2.6.27
Signed-off-by: David S. Miller <davem@davemloft.net>
We've introduced extra need of compat layer for ip_tunnel_prl{}
for PRL (Potential Router List) management. Though compat_ioctl
is still missing in ipv4/ipv6, let's make the interface more
straight-forward and eliminate extra need for nasty compat layer
anyway since the interface is new for 2.6.26.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a htb_hysteresis parameter to htb_sch.ko and by sysfs magic make
it runtime adjustable via
/sys/module/sch_htb/parameters/htb_hysteresis mode 640.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Acked-by: Martin Devera <devik@cdi.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HTB hysteresis mode reduce the CPU load, but at the
cost of scheduling accuracy.
On ADSL links (512 kbit/s upstream), this inaccuracy introduce
significant jitter, enought to disturbe VoIP. For details see my
masters thesis (http://www.adsl-optimizer.dk/thesis/), chapter 7,
section 7.3.1, pp 69-70.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Acked-by: Martin Devera <devik@cdi.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Remove ->hangup() from stack glue operations.
ocfs2: Move the call of ocfs2_hb_ctl into the stack glue.
ocfs2: Move the hb_ctl_path sysctl into the stack glue.
The ->hangup() call was only used to execute ocfs2_hb_ctl. Now that
the generic stack glue code handles this, the underlying stack drivers
don't need to know about it.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Take o2hb_stop() out of the o2cb code and make it part of the generic
stack glue as ocfs2_leave_group(). This also allows us to remove the
ocfs2_get_hb_ctl_path() function - everything to do with hb_ctl is now
part of stackglue.c. o2cb no longer needs a ->hangup() function.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
ocfs2 needs to call out to the hb_ctl program at unmount for all cluster
stacks. The first step is to move the hb_ctl_path sysctl out of the
o2cb code and into the generic stack glue.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (21 commits)
[POWERPC] Turn on ATA_SFF so we get SATA_SVW back in defconfigs
[POWERPC] Remove ppc32's export of console_drivers
[POWERPC] Fix -Os kernel builds with newer gcc versions
[POWERPC] Fix bootwrapper builds with newer gcc versions
[POWERPC] Build fix for drivers/macintosh/mediabay.c
[POWERPC] Fix warning in pseries/eeh_driver.c
[POWERPC] Add missing of_node_put in drivers/macintosh/therm_adt746x.c
[POWERPC] Add missing of_node_put in drivers/macintosh/smu.c
[POWERPC] Add missing of_node_put in pseries/nvram.c
[POWERPC] Fix return value check logic in debugfs virq_mapping setup
[POWERPC] Fix rmb to order cacheable vs. noncacheable
powerpc/spufs: fix missed stop-and-signal event
powerpc/spufs: synchronize interaction between spu exception handling and time slicing
powerpc/spufs: remove class_0_dsisr from spu exception handling
powerpc/spufs: wait for stable spu status in spu_stopped()
[POWERPC] bootwrapper: add simpleImage* to list of boot targets
[POWERPC] 83xx: MPC837xRDB's VSC7385 ethernet switch isn't on the MDIO bus
[POWERPC] Updated Freescale PPC defconfigs
[POWERPC] 8610: Update defconfig for MPC8610 HPCD
[POWERPC] 85xx: MPC8548CDS - Fix size of PCIe IO space
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Au1200: MMC resource size off by one
[MIPS] TANBAC: Update defconfig
[MIPS] Vr41xx: Initialize PCI io_map_base
[MIPS] Malta: Always compile MTD platform device registration code.
[MIPS] Malta: Fix build errors for 64-bit kernels
[MIPS] Lasat: sysctl fixup
[MIPS] Fix buggy use of kmap_coherent.
[MIPS] Lasat: bring back from the dead
[MIPS] vpe_id is required for VSMP and SMTC builds
[MIPS] Export smp_call_function and smp_call_function_single.
[MIPS] Bring the SWARM defconfig up to date
[MIPS] Sibyte: Build RTC support as an object
[MIPS] Fix the fix for divide by zero error in build_{clear,copy}_page
[MIPS] Fix build for PNX platforms.
[MIPS] Add RM200 with R5000 CPU to known ARC machines
[MIPS] Better load address for big endian SNI RM
[MIPS] SB1250: Initialize io_map_base
[MIPS] Alchemy: Add au1500 reserved interrupt
[MIPS] Export empty_zero_page for sake of the ext4 module.
This seems to have been removed accidentally in commit
ed7b1889da ("Unexport asm/page.h"), but
wasn't supposed to have been -- the original patch at
http://lkml.org/lkml/2007/10/30/144 just moved it from $(header-y) to
$(unifdef-y)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This file is only included where it makes sense now, so there's no need
for the CONFIG_ARCH_SUPPORTS_AOUT conditional -- and that conditional is
bad, because we want to export <linux/a.out.h> to userspace.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit d20894a237 ("Remove a.out
interpreter support in ELF loader"), Andi removed support for a.out
interpreters from the ELF loader, which was only ever needed for the
transition from a.out to ELF.
This removes the last traces of that support, in particular the
inclusion of <linux/a.out.h>.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ang Way Chuang
Radu Cristescu
David Brownell
Stephen Hemminger
Dhananjay Phadke
Josh Boyer
Linus Torvalds
Miklos Szeredi
Eduard - Gabriel Munteanu
Steffen Klassert
Patrick McHardy
Thomas Mingarelli
Oliver Neukum
Jiri Kosina
Rabin Vincent
Chas Williams
Robert T. Johnson
Eric Kinzie
Jorge Boncompte [DTI2]
Rami Rosen
Eric Dumazet
Ben Hutchings
Vlad Yasevich
Wei Yongjun
David S. Miller
YOSHIFUJI Hideaki
Jesper Dangaard Brouer
Joel Becker
David Woodhouse