This is a revised version of an earlier patch to add support to usbcore
for driving root hubs by interrupts rather than polling.
There's a temporary flag added to struct usb_hcd, marking devices whose
drivers are aware of the new mechanism. By default that flag doesn't get
set so drivers will continue to see the same polling behavior as before.
This way we can convert the HCDs one by one to use interrupt-based event
reporting, and the temporary flag can be removed when they're all done.
Also included is a small change to the hcd_disable_endpoint routine.
Although endpoints normally shouldn't be disabled while a controller is
suspended, it's legal to do so when the controller's driver is being
rmmod'ed.
Lastly the patch adds a new callback, .hub_irq_enable, for use by HCDs
where the root hub's port-change interrupts are level-triggered rather
than edge-triggered. The callback is invoked each time khubd has finished
processing a root hub, to let the HCD know that the interrupt can safely
be re-enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After all the discussion you might not be interested in this still, but
nevertheless here it is. This patch adds a shutdown method to the
uhci-hcd driver. Its prerequisite is the patch you wrote adding shutdown
support for PCI.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch improves the strategy uhci-hcd uses for performing controller
resets and checking whether they are needed.
The HCRESET command doesn't affect the Suspend, Resume,
or Reset bits in the port status & control registers, so
the driver must clear them by itself. This means the
code to figure out how many ports there are has to be moved
to an earlier spot in the driver.
The R/WC bits in the USBLEGSUP register can be set by the
hardware even in the absence of BIOS meddling with legacy
support features. Hence it's not a good idea to check them
while trying to determine whether the BIOS has altered the
controller's state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch, which has as478b as a prerequisite, enables the uhci-hcd
driver to take advantage of root-hub IRQs rather than polling during the
time it is suspended. (Unfortunately the hardware doesn't support
port-change interrupts while the controller is running.) It also turns
off the driver's private timer while the controller is suspended, as it
isn't needed then. The combined elimination of polling interrupts and
timer interrupts ought to be enough to allow some systems to save a
noticeable amount of power while they are otherwise idle.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tidies up a few loose ends left by the preceding patches.
It indicates the controller supports remote wakeup whenever the PM
capability is present -- which shouldn't cause any harm if the
assumption turns out to be wrong. It refuses to suspend the
controller if the root hub is still active, and it refuses to resume
the root hub if the controller is suspended. It adds checks for a
dead controller in several spots, and it adds memory barriers as
needed to insure that I/O operations are completed before moving on.
Actually I'm not certain the last part is being done correctly. With
code like this:
outw(..., ...);
mb();
udelay(5);
do we know for certain that the outw() will complete _before_ the
delay begins? If not, how should this be written?
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements (finally!) separate suspend and resume routines
for the root hub and the controller in the UHCI driver. It also
changes the sequence used to reset the controller during initial
probing, so as to preserve the existing state during a Resume-From-Disk.
(This new sequence is what should be used in the PCI Quirks code for
early USB handoffs, incidentally.) Lastly it adds a notion of the
controller being "inaccessible" while in a PCI low-power state, when
normal I/O operations shouldn't be allowed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch starts making some serious changes to the UHCI driver.
There's a set of private states for the root hub, and the internal
routines for suspending and resuming work completely differently, with
transitions based on the new states. Now the driver distinguishes
between a privately auto-stopped state and a publicly suspended state,
and it will properly suspend controllers with broken resume-detect
interrupts instead of resetting them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes a few small improvements in the UHCI driver. Some
code is moved between different source files and a more useful pointer
is passed to a callback routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves a few subroutines around in the uhci-hcd source file.
Nothing else is changed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch turns a user mode driver error into a hard error, and updates
the relevant diagnostic slightly to help troubleshooting. gphoto was
known to have this problem, hopefully it is now fixed (they have had
plenty of warning...)
This had been left as a soft error to give various user mode drivers a
change to be properly fixed, with the statement that starting in about
2.6.10 it would be changed. It had been mostly safe as a soft error ...
but that can not be guaranteed. Now that a year has passed, it's time to
really insist that the user mode drivers finally fix their relevant bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an oops triggered at rmmod of isp116x-hcd
after the probe() has failed.
Also, it extends the error message printed, if the driver
cannot detect "Chip's Clock Ready" after a software reset.
As Ian Campbell recently reported, this happens if the
chip's H_WAKEUP pin is not pulled low during software reset.
Several people have already had this issue, hence the update
to the error message.
Also, extend the error message about the failed clock
detection after the software reset.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
This patch provides an "isp116x-hcd" driver for Philips'
ISP1160/ISP1161 USB host controllers.
The driver:
- is relatively small, meant for use on embedded platforms.
- runs usbtests 1-14 without problems for days.
- has been in use by 6-7 different people on ARM and PPC platforms,
running a range of devices including USB hubs.
- supports suspend/resume of both the platform device and the root hub;
supports remote wakeup of the root hub (but NOT the platform device)
by USB devices.
- does NOT support ISO transfers (nobody has asked for them).
- is PIO-only.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various USB patches, mostly for portability:
- Fifo mode 1 didn't work previously (oopsed), so now it's fixed and
(why not) defines even more endpoints for composite devices.
- OMAP 1710 doesn't have an internal transceiver.
- Small PM update: if the USB link is suspended, don't disconnect on
entry to deep sleep.
- Be more correct about handling zero length control reads. OMAP
seems to mis-handle that protocol peculiarity though; best avoided.
- Platform device resources (for UDC and OTG controllers) now use
physical addresses, so /proc/iomem is more consistent.
- Minor cleanups, notably (by volume) for "sparse" NULL warnings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch changes the g_file_storage driver to make the "stall" module
parameter generally available; currently it is available only if the
testing version of the module has been configured. It also fixes a typo
in a comment -- thanks, Pat!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch simplifies the g_file_storage driver by consolidating a bunch
of min() calculations at a single spot.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CONFIG_CONFIG_TUNER_MULTI_I2C probably isn't what the
author meant to create.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If cfq is managing a queue and a new scheduler is later selected, it is
possible for the cfqd unplug_work work to be queued after the kblockd
work struct has been flushed. The problem is the ordering of
cfq_shutdown_timer_wq() and blk_put_queue() in cfq_put_cfqd(). The
latter may rearm the work, leaving cfq_kick_queue() with dead data.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Adjust slice values
- Instead of one async queue, one is defined per priority level. This
prevents kernel threads (such as reiserfs/x and others) that run at
higher io priority from conflicting with others. Previously, it was a
coin toss what io prio the async queue got, it was defined by who
first set up the queue.
- Let a time slice only begin, when the previous slice is completely
done. Previously we could be somewhat unfair to a new sync slice, if
the previous slice was async and had several ios queued. This might
need a little tweaking if throughput suffers a little due to this,
allowing perhaps an overlap of a single request or so.
- Optimize the calling of kblockd_schedule_work() by doing it only when
it is strictly necessary (no requests in driver and work left to do).
- Correct sync vs async logic. A 'normal' process can be purely async as
well, and a flusher can be purely sync as well. Sync or async is now a
property of the class defined and requests pending. Previously writers
could be considered sync, when they were really async.
- Get rid of the bit fields in cfqq and crq, use flags instead.
- Various other cleanups and fixes
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In cfq_find_next_crq(), cfq tries to find the next request by choosing
one of two requests before and after the current one. Currently, when
choosing the next request, if there's no next request, the next
candidate is NULL, resulting in selection of the previous request. This
results in weird scheduling. Once we reach the end, we always seek
backward.
The correct behavior is using the first request as the next candidate.
cfq_choose_req() already has logics for handling wrapped requests.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the CFQ io scheduler to the new time sliced design (cfq
v3). It provides full process fairness, while giving excellent
aggregate system throughput even for many competing processes. It
supports io priorities, either inherited from the cpu nice value or set
directly with the ioprio_get/set syscalls. The latter closely mimic
set/getpriority.
This import is based on my latest from -mm.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add separate files for the different 8250 ISA-based serial boards.
Looking across all the various architectures, it seems reasonable that
we can key the availability of the configuration options for these
beasts to the bus-related symbols (iow, CONFIG_ISA). We also standardise
the base baud/uart clock rate for these boards - I'm sure that isn't
architecture specific, but is solely dependent on the crystal fitted
on the board (which should be the same no matter what type of machine
its fitted into.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
68328serial.c does not make use of register_serial/unregister_serial,
which is traditionally used to register 8250-compatible UARTs with
the 8250-compatible serial driver.
Acked-by: David McCullough
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check the link state during b44_open. This closes a 1 HZ window
that existed after b44_open ran but before the b44_timer handler ran,
during which ethtool would report "Link detected: yes" no matter what
the link state actually was.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the tulip driver to suspend and resume properly. It was
originally written by Karsten Keil and then modified by Adam Belay.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
drivers/net/wireless/prism54/isl_38xx.c:131: warning: 'current_time.tv_sec' is used uninitialized in this function
drivers/net/wireless/prism54/isl_38xx.c:131: warning: 'current_time.tv_usec' is used uninitialized in this function
Signed-off-by: Olaf Hering <olh@suse.de>
Some USB ethernet drivers did not accept multicast frames appropriately.
IPv6 did not work with those drivers without this patch.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Jeff,
Just incase this got lost in the recent netdev mailing list transition
here is a nicer version of Andy's patch for gianfar.
- kumar
* TCP/IP/UDP checksumming and verification
* VLAN tag insertion/extraction
* Larger multicast hash-table
* Padding to align IP headers
Also added:
* msg lvl support
* Some whitespace cleanup
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
The race causes a kernel oops when smc_hardware_send_pkt() tries to
dereference pending_tx_skb which would have been freed from one of the
driver reset paths just after the tx_task tasklet has been scheduled.
This race is possible on SMP but was uncovered by the kernel RT work.
Signed-off-by: Nicolas Pitre <nico@cam.org>
--Boundary-00=_F5lsC5eH1wGW5o9
Content-Type: text/plain;
charset="koi8-r"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
Hi Jeff,
In some messages in via-rhine.c there is a leading space
for no apparent reason. This patch removes it.
--
vda
--Boundary-00=_F5lsC5eH1wGW5o9
Content-Type: text/x-diff;
charset="koi8-r";
name="via-rhine.c.diff"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
filename="via-rhine.c.diff"
Driver version, white space, comments & other
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Included proposals to false late collisions due to H/W latencies
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Ethtool set speed/duplex validates parameters for consistency
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Ethtool cleanup patch from Stephen Hemminger
* use ADVERTISED_xxx fields when setting advertised fields
* don't hardcode constant for advertised field
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fixed the loopback test failure for 82573 based adapters
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fixed register and loopback test failures with 82573 controllers
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Cleanup debug message printed when Tx Unit hang is detected
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use netdev_priv() to get to netdev->priv - from shemminger@osdl.org
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use correct WOL settings for 82544 adapters
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
NAPI performance enhancements - Fixed issues with shared interrupts and NAPI resulting in bad performance.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
e100_eeprom_load was called after e100_phy_init causing phy_init
not to use values set in EEPROM - from emann@mrv.com
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Added patch from Eran Mann to fix following e100 MDI/MDI-X issues
* MDI/MDI-X autodetection should never be enabled for 82551ER/QM chips
* enabling this feature based on eeprom settings
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
If the frame has ToDS flag set, mark it by setting skb->pkt_type to
PACKET_OTHERHOST, so that applications unaware of promiscous mode won't get
uplink (STA->AP) packets for STA->STA transmissions relayed by the AP.
Thanks to John Denker and David Gibson for finding the problem and the
solution.
Patch from Pavel Roskin
This patch is to provide support for cs89x0-based network device on
Philips' pnx0105 board.
Signed-off-by: dmitry pervushin <dpervushin@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
These patches include dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Use ssleep() / msleep_interruptible() [as appropriate]
instead of schedule_timeout() to guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Use msleep_interruptible() instead of schedule_timeout() to
guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Insert set_current_state() before schedule_timeout() so the
function delays as expected. Without the addition, schedule_timeout()
will return immediately.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Use ssleep() instead of nicedelay()
to guarantee the task delays as expected. Remove the prototype and
definition of nicedelay(). This is a very weird function, because it is
called to sleep in terms of usecs, but always sleeps for 1 second,
completely ignoring the parameter. I have gone ahead and followed suit,
just sleeping for a second in all cases, but maybe someone with the
hardware could tell me if perhaps the paramter *should* matter. Additionally,
nicedelay() is called in TASK_INTERRUPTIBLE state, but doesn't deal with signals
in case these longer delays do not complete, so I believe ssleep() is more
appropriate.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
This patch fixes two bugs in the dm9000 network driver:
- Don't read one byte too much in 8bit mode.
- release correct resource
Signed-off-by: Jochen Karrer <j.karrer@lightmaze.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix int vs. pm_message_t confusion in airo. Should change no code.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This is a fix for the interrupt handler in the defxx driver to use
irqreturn_t. Beside the obvious fix of returning a proper status at all,
it actually checks board registers as appropriate for determining if an
interrupt has been recorded in the bus-specific interface logic.
The patch also includes an obvious one-line fix for SET_NETDEV_DEV needed
for the EISA variation, for which I've decided there is no point in sending
separately.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
drivers/net/tulip/dmfe.c: In function `dmfe_parse_srom':
drivers/net/tulip/dmfe.c:1805: warning: passing arg 1 of `__le16_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type
This is basically a guess:
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The 8129/8130 support is a sub-option that is not visible if the user
hasn't enabled the 8139 support.
Let's make it a bit easier for users to find the driver for their nic.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch contains the follwing cleanups:
- make needlessly global code static
- remove obsolete Emacs settings
Signed-off-by: Adrian Bunk <bunk@stusta.de>
During some performance diagnostics I stumbled on this slightly wasteful
code in pcnet_cs.c which I made the patch included at the bottom for (two
minor comment fixes included).
Improvement:
instead of *always* calculating
lea 0x2c0(%edx),%ebx
and then additionally doing the
mov %edx,0xc0(%ebx)
addition *if we need it*,
we now do the *whole* calculation of
mov %edx,0x380(%ebx)
*only* if we need it.
This even manages to save us a whole 16-byte alignment buffer loss
in this compilation case.
Result: slightly improves IRQ handler performance in both shared and
non-shared IRQ case, which should make my rusty P3/700 a slight bit happier.
Thank you for your support,
Andreas Mohr
old asm result (using gcc 3.3.5):
000015a0 <ei_irq_wrapper>:
15a0: 55 push %ebp
15a1: 89 e5 mov %esp,%ebp
15a3: 53 push %ebx
15a4: 8d 9a c0 02 00 00 lea 0x2c0(%edx),%ebx
15aa: e8 fc ff ff ff call 15ab <ei_irq_wrapper+0xb>
15af: 83 f8 01 cmp $0x1,%eax
15b2: 74 03 je 15b7 <ei_irq_wrapper+0x17>
15b4: 5b pop %ebx
15b5: 5d pop %ebp
15b6: c3 ret
15b7: 31 d2 xor %edx,%edx
15b9: 89 93 c0 00 00 00 mov %edx,0xc0(%ebx)
15bf: eb f3 jmp 15b4 <ei_irq_wrapper+0x14>
15c1: eb 0d jmp 15d0 <ei_watchdog>
15c3: 90 nop
15c4: 90 nop
15c5: 90 nop
15c6: 90 nop
15c7: 90 nop
15c8: 90 nop
15c9: 90 nop
15ca: 90 nop
15cb: 90 nop
15cc: 90 nop
15cd: 90 nop
15ce: 90 nop
15cf: 90 nop
000015d0 <ei_watchdog>:
new asm result:
000015a0 <ei_irq_wrapper>:
15a0: 55 push %ebp
15a1: 89 e5 mov %esp,%ebp
15a3: 53 push %ebx
15a4: 89 d3 mov %edx,%ebx
15a6: e8 fc ff ff ff call 15a7 <ei_irq_wrapper+0x7>
15ab: 83 f8 01 cmp $0x1,%eax
15ae: 74 03 je 15b3 <ei_irq_wrapper+0x13>
15b0: 5b pop %ebx
15b1: 5d pop %ebp
15b2: c3 ret
15b3: 31 d2 xor %edx,%edx
15b5: 89 93 80 03 00 00 mov %edx,0x380(%ebx)
15bb: eb f3 jmp 15b0 <ei_irq_wrapper+0x10>
15bd: 8d 76 00 lea 0x0(%esi),%esi
000015c0 <ei_watchdog>:
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Make sure the code compiles with and without ARLAN_ENTRY_EXIT_DEBUGGING.
Only provide parameter descriptions when parameters are defined.
Remove "arlan_"-prefix to shape up built-in parameter names:
arlan.arlan_debug -> arlan.debug
arlan.arlan_EEPROM_bad -> arlan.EEPROM_bad
arlan.arlan_entry_and_exit_debug -> arlan.entry_and_exit_debug
arlan.arlan_entry_debug -> arlan.entry_debug
arlan.arlan_exit_debug -> arlan.exit_debug
Signed-off-by: Magnus Damm <damm@opensource.se>
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom
macros.
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
The spin loop in 8139cp is limited to 100 iterations when pulling hardware
stats. There is no allowance for processor speed so on a fast machine, the
stats may not be available that fast. Also, if the board doesn't return
soon enough make sure turn the address back off to prevent later updates
when memory has gone away.
Add support for alternate slave selection algorithms to bonding
balance-xor and 802.3ad modes. Default mode (what we have now: xor of
MAC addresses) is "layer2", new choice is "layer3+4", using IP and port
information for hashing to select peer.
Originally submitted by Jason Gabler for balance-xor mode;
modified by Jay Vosburgh to additionally support 802.3ad mode. Jason's
original comment is as follows:
The attached patch to the Linux Etherchannel Bonding driver modifies the
driver's "balance-xor" mode as follows:
- alternate hashing policy support for mode 2
* Added kernel parameter "xmit_policy" to allow the specification
of different hashing policies for mode 2. The original mode 2
policy is the default, now found in xmit_hash_policy_layer2().
* Added xmit_hash_policy_layer34()
This patch was inspired by hashing policies implemented by Cisco,
Foundry and IBM, which are explained in
Foundry documentation found at:
http://www.foundrynet.com/services/documentation/sribcg/Trunking.html#112750
Signed-off-by: Jason Gabler <jygabler@lbl.gov>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Add support for generating gratuitous ARPs in bonding
active-backup mode when failovers occur. Includes support for VLAN
tagging the ARPs as needed.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
After the previous fix in 2.6.12, this patch should properly fix the
radeon IRQ handling code.
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
1. Establish a simple API for process freezing defined in linux/include/sched.h:
frozen(process) Check for frozen process
freezing(process) Check if a process is being frozen
freeze(process) Tell a process to freeze (go to refrigerator)
thaw_process(process) Restart process
frozen_process(process) Process is frozen now
2. Remove all references to PF_FREEZE and PF_FROZEN from all
kernel sources except sched.h
3. Fix numerous locations where try_to_freeze is manually done by a driver
4. Remove the argument that is no longer necessary from two function calls.
5. Some whitespace cleanup
6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
cleared before setting PF_FROZEN, recalc_sigpending does not check
PF_FROZEN).
This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since kernel 2.6.3 the Kconfig text explicitely stated this driver was
obsolete.
(trolling for IBMers)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no need for a function that only calls udelay.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use msleep_interruptible() instead of schedule_timeout() in send_break() to
guarantee the task delays as expected. Change @duration's units to
milliseconds, and modify arguments in callers appropriately.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use msleep_interruptible() instead of schedule_timeout() in send_break() to
guarantee the task delays as expected. Change @duration's units to
milliseconds, and modify arguments in callers appropriately.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
wanpipe.txt and wan-router.txt in Documentation/networking contain the exact
same information (diff between the two shows no drivers/net/wan/Kconfig.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following cleanups:
- make needlessly global functions static
- remove the following unused global function:
- cm206_delay
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following cleanups:
- i2cmd.c: #if 0 the unused function i2cmdUnixFlags
- i2cmd.c: make the needlessly global funciton i2cmdBaudDef static
- ip2main.c: remove dead code that wasn't reachable due to an #ifdef
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's a patch with kfree() cleanups for drivers/firmware/efivars.c Patch
removes redundant NULL checks before kfree and also makes a small
whitespace cleanup - moves two statements on same line to separate lines.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes redundant checks for NULL pointer before kfree() in
drivers/telephony/
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no need to check for NULL, kfree() can cope.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following cleanups:
- make needlessly global code static
- remove the following unused global functions:
- blkdev_scsi_issue_flush_fn
- __blk_attempt_remerge
- remove the following unused EXPORT_SYMBOL's:
- blk_phys_contig_segment
- blk_hw_contig_segment
- blkdev_scsi_issue_flush_fn
- __blk_attempt_remerge
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes some dead code found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes some obviously dead code found by the Coverity
checker.
This patch was already ACK'ed by Petr Vandrovec.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following cleanups:
- make needlessly global code static
- remove the TRUE/FALSE macros
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- make the needlessly global function __nvram_set_checksum static
- #if 0 the unused global function nvram_set_checksum
- remove the EXPORT_SYMBOL's for both functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following cleanups:
- make a needlessly global function static
- #if 0 the unused global function dsp3780I_ReadGenCfg
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes an unneeded global variable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk() calls should include appropriate KERN_* constant.
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk() calls should include appropriate KERN_* constant.
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the MSECS_TO_JIFFIES() macro because msescs_to_jiffies() from
jiffies.h should be used. The macro isn't referenced anywhere anyway.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes #if's for kernel 2.2 .
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the following bugs:
- __exit unregister_ioregion and unregister_drivers were called by
__init isicom_init
- __init isicom_init was called by __devinit isicom_setup
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following cleanups:
- make needlessly global code static
- remove or #if 0 the following unused functions:
- tul_pop_pend_scb
- tul_device_reset
- tul_reset_scsi_bus
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use msleep_interruptible() instead of schedule_timeout() in send_break() to
guarantee the task delays as expected. Change @duration's units to
milliseconds, and modify arguments in callers appropriately. Patch is
compile-tested.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not sure why any driver needs to sleep for *two* ticks, so let's fix it.
Use msleep() instead of schedule_timeout() to guarantee the task delays as
expected. Signals are never checked for by the callers or in the function
itself, so use TASK_UNINTERRUPTIBLE instead of TASK_INTERRUPTIBLE. The
delay is presumed to have been written when HZ==100, and thus has been
multiplied by 10 to pass to msleep().
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bunch of whitespace oddities and use `unsigned long' for a
jiffies-holding variable.
Signed-off-by: M.Baris Demiray <baris@labristeknoloji.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
au1100: use C99 struct init.
Signed-off-by: randy_dunlap <rdunlap@xenotime.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch #if 0's an unused function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following cleanups:
- make some needlessly global functions static
- b1dma.c __init/__exit the functions b1dma_{init,exit}
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage of mca_find_device_by_slot in
the kernel, and this patch therefore removes the EXPORT_SYMBOL.
This patch should be safe since mca-legacy is nothing drivers should
move to.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- make needlessly global code static
- remove the following unused global function:
- isdn_audio.c: isdn_audio_2adpcm_flush
- remove the following unused struct:
- isdn_net.c: isdn_concap_demand_dial_dops
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- make some needlessly global functions static
- remove the following unused global functions:
- callbacks.c: cb_out_3
- capi.c: capi_decode_disc_conf
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanips:
- make some needlessly global code static
- remove the compiled but completely unused debug.c
- remove or #if 0 the following unused global functions:
- command.c: loopback
- command.c: loadproc
- init.c: irq_supported
- packet.c: print_skb
- shmem.c: memset_shmem
- timer.c: trace_timer
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
vesafb will do really silly things like..
mtrr: type mismatch for e0000000,8000000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,4000000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,2000000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,1000000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,800000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,400000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,200000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,100000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,80000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,40000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,20000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,10000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,8000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,4000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,2000 old: write-back new: write-combining
mtrr: type mismatch for e0000000,1000 old: write-back new: write-combining
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x800 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x400 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x200 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x100 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x80 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x40 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x20 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x10 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x8 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x4 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x2 base: 0xe0000000
mtrr: size and base must be multiples of 4 kiB
mtrr: size: 0x1 base: 0xe0000000
Stop scaling down at PAGE_SIZE.
Also fix up some broken indentation.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch provides purely cosmetic changes and corrects CodingStyle
guide lines related certain issues like below in kexec related files
o braces for one line "if" statements, "for" loops,
o more than 80 column wide lines,
o No space after "while", "for" and "switch" key words
o Changes:
o take-2: Removed the extra tab before "case" key words.
o take-3: Put operator at the end of line and space before "*/"
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Makes kexec_crashdump() take a pt_regs * as an argument. This allows to
get exact register state at the point of the crash. If we come from direct
panic assertion NULL will be passed and the current registers saved before
crashdump.
This hooks into two places:
die(): check the conditions under which we will panic when calling
do_exit and go there directly with the pt_regs that caused the fatal
fault.
die_nmi(): If we receive an NMI lockup while in the kernel use the
pt_regs and go directly to crash_kexec(). We're probably nested up badly
at this point so this might be the only chance to escape with proper
information.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a sysrq-trigger mechanism for kexec based crashdumps. Alt-Sysrq-c
triggers a kexec based crashdump.
Signed-off-by: Hariprasad Nellitheertha <hari@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed the dependency on backup region. Now all the information is encoded
in ELF format. /dev/oldmem is a dummy interface. User space tool need to be
intelligent enough to parse the elf headers and read the relevant memory areas
with the help of /dev/oldmem.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hariprasad Nellitheertha <hari@in.ibm.com>
This patch contains the code that enables us to access the previous kernel's
memory as /dev/oldmem.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We don't need to use do_div() on a 32-bit quantity.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was using invalid memory for the miscdevice.name. This patch fixes the
problem which was manifested by an ugly entry in /proc/misc.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix parsing of the PUBEK for display which was leading to showing the wrong
modulus length and modulus.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is work to support new National TPMs that problems were reported
with on Thinkpad T43 and Thinkcentre S51. Thanks to Jens and Gang for
their debugging work on these issues.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.12-rc6-mm1 has a few remaining synchronize_kernel()s, some (but not
all) in comments. This patch changes these synchronize_kernel() calls (and
comments) to synchronize_rcu() or synchronize_sched() as follows:
- arch/x86_64/kernel/mce.c mce_read(): change to synchronize_sched() to
handle races with machine-check exceptions (synchronize_rcu() would not cut
it given RCU implementations intended for hardcore realtime use.
- drivers/input/serio/i8042.c i8042_stop(): change to synchronize_sched() to
handle races with i8042_interrupt() interrupt handler. Again,
synchronize_rcu() would not cut it given RCU implementations intended for
hardcore realtime use.
- include/*/kdebug.h comments: change to synchronize_sched() to handle races
with NMIs. As before, synchronize_rcu() would not cut it...
- include/linux/list.h comment: change to synchronize_rcu(), since this
comment is for list_del_rcu().
- security/keys/key.c unregister_key_type(): change to synchronize_rcu(),
since this is interacting with RCU read side.
- security/keys/process_keys.c install_session_keyring(): change to
synchronize_rcu(), since this is interacting with RCU read side.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch fix gcc 4 compilation errors in drivers/serial/mpsc.c
Signed-off-by: Lee Nicks <allinux@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the memory allocation method for the s390 debug feature.
Trace buffers had been allocated using the get_free_pages() function before.
Therefore it was not possible to get big memory areas in a running system due
to memory fragmentation. Now the trace buffers are subdivided into several
subbuffers with pagesize. Therefore it is now possible to allocate more
memory for the trace buffers and more trace records can be written.
In addition to that, dynamic specification of the size of the trace buffers is
implemented. It is now possible to change the size of a trace buffer using a
new debugfs file instance. When writing a number into this file, the trace
buffer size is changed to 'number * pagesize'.
In the past all the traces could be obtained from userspace by accessing files
in the "proc" filesystem. Now with debugfs we have a new filesystem which
should be used for debugging purposes. This patch moves the debug feature
from procfs to debugfs.
Since the interface of debug_register() changed, all device drivers, which use
the debug feature had to be adjusted.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add interface to issue VM control program commands.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Improved machine check handling. Kernel is now able to receive machine checks
while in kernel mode (system call, interrupt and program check handling).
Also register validation is now performed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix compile breakage in the dcss block driver introduced by the attribute
changes.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert the dasd driver to use the new klist interface.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alan Stern
David Brownell
Olav Kongas
Dave Jones
Jens Axboe
Russell King
Philip Pokorny
John W. Linville
Adam Belay
Olaf Hering
YOSHIFUJI Hideaki
Randy Dunlap
Kumar Gala
Nicolas Pitre
Denis Vlasenko
Malli Chilakala
Jeff Garzik
Christoph Hellwig
dmitry pervushin
Adrian Bunk
Hideki Yamane
Manfred Spraul
Tobias Klauser
Nishanth Aravamudan
Domen Puncer
Sascha Hauer
Pavel Machek
Maciej W. Rozycki
Andrew Morton
Andreas Mohr
Magnus Damm
Stephen Hemminger
Kumar Gala
Jay Vosburgh
Ralf Baechle
Linus Torvalds
Dave Airlie
Christoph Lameter
Nikita Danilov
Jesper Juhl
M.Baris Demiray
Jon Smirl
Jurriaan on adsl-gate
Maneesh Soni
Alexander Nyberg
Hariprasad Nellitheertha
Vivek Goyal
Kylene Jo Hall
Paul E. McKenney
Lee Nicks
Michael Holzheu
Christian Borntraeger
Heiko Carstens
Cornelia Huck