* Rename 'simplex_stat' variable to 'dma_stat' in ide_get_or_set_dma_base().
* Factor out code for forcing host out of "simplex" mode from
ide_get_or_set_dma_base() to ide_pci_clear_simplex() helper.
* Add IDE_HFLAG_CLEAR_SIMPLEX host flag and set it in alim15x3 (for M5229),
amd74xx (for AMD 7409), cmd64x (for CMD643), generic (for Netcell) and
serverworks (for CSB5) host drivers.
* Make ide_get_or_set_dma_base() test for IDE_HFLAG_CLEAR_SIMPLEX host flag
instead of checking dev->device (BTW the code was buggy because it didn't
check for dev->vendor, luckily none of these PCI Device IDs was used by
some other vendor for PCI IDE controller).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer needed assertion from amd74xx_probe().
* Factor out cable detection for AMD7409 to amd7409_cable_detect() and for
chipsets >= AMD7411 to amd7411_cable_detect().
* Use dev->vendor and dev->device instead of amd_config->udma_mask when
selecting cable detection method and checking for broken FIFO support in
init_chipset_amd74xx().
* Remove no longer needed AMD_BAD_FIFO define.
* Add 'swdma' parameter for setting .swdma_mask to DECLARE_AMD_DEV() macro.
* Add 'udma' parameter for setting .udma_mask to DECLARE_{AMD,NV}_DEV() macro.
* Keep a copy of a current amd74xx_chipsets[] entry in amd74xx_probe()
in order to fix ->swdma_mask on early AMD7409 revisions and ->udma_mask
on Serenade mainboards.
* Remove no longer needed fixups from init_chipset_amd74xx()
and AMD_CHECK_{SWDMA,SERENADE} defines.
* Move printing banner message from init_chipset_amd74xx() to amd74xx_probe(),
also remove incorrect comment while at it.
* Use hwif->ultra_mask instead of amd_config->udma_mask in amd_set_drive().
* Add 'udma_mask' argument to amd_set_speed() and pass UDMA mask from
amd_set_drive() instead of using amd_config->udma_mask.
* Move amd_config->base from AMD_* defines to users of these defines and add
0x40 the defined values. Then add amd_offset() inline helper for selecting
offset from 0x40 base (needed for nVidia controllers) and finally use it in
amd_set_speed(), amd7411_cable_detect() and init_chipset_amd74xx() instead
of amd_config->base.
* Remove no longer needed AMD_BAD_SWDMA define, ->{swdma,ultra}_mask setup
from init_hwif_amd74xx(), amd_{config,chipset} variables and amd_ide_chips
table.
* Fix init_chipset_amd74xx() comment.
* Bump driver version.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().
* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
(aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
methods in host drivers that don't (IDE core code guarantees that
->set_dma_mode will be called only for modes which are present
in SWDMA/MWDMA/UDMA masks).
While at it:
* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
hpt34x/hpt366/pdc202xx_old/serverworks host driver.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_{IO_32BIT,UNMASK_IRQS} host flag to tell ide_pci_setup_ports()
to set drive->{io_32bit,unmask} for both drives on the interface. Convert
amd74xx, sl82c105 and via82cxxx host drivers to use these new host flags.
While at it:
* Add IDE_HFLAGS_AMD define (amd74xx host driver).
* Add IDE_HFLAGS_VIA define (via82cxxx host driver).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:
generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method
it821x.c:
* if memory allocation fails drive->autotune won't be set
(but there also won't be ->set_pio_mode method in such case)
piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)
However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.
* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
method may still override them).
* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.
While at it:
* Use ATA_{UDMA,MWDMA,SWDMA}* defines.
* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.
* serverworks.c: fix DMA masks being set before checking DMA base.
v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags. Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define. Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA. Then remove no longer needed hwif->atapi_dma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
6723 2000 28 8751 222f drivers/ide/pci/amd74xx.o.before
3833 2000 16 5849 16d9 drivers/ide/pci/amd74xx.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drive->dn is initialized by ide-probe.c::probe_hwif() so no need to do it
in ->init_hwif method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.
* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program
the host for the transfer mode after programming the device. Set it
in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
and via82cxxx host drivers.
* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
skip programming of host/device for the transfer mode ("smart" hosts).
Set it in it821x host driver and check it in ide_tune_dma().
* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
direct ->set_pio_mode/->speedproc users to use these helpers.
* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
methods to callers.
* Rename ->speedproc method to ->set_dma_mode, make it void and update
all implementations accordingly.
* Update ide_set_xfer_rate() comments.
* Unexport ide_config_drive_speed().
v2:
* Fix issues noticed by Sergei:
- export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
to setting DMA modes from sc1200_set_pio_mode() to do_special()
- check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
- check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
- check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
- return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
- don't set ->set_{pio,dma}_mode on it821x in "smart" mode
- fix build problem in pmac.c
- minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
- improve patch description
Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
the device (not really an issue since 0x00 is not supported correctly by
any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Check ide_config_drive_speed() return value.
* While at also call ide_config_drive_speed() if the transfer mode is
XFER_PIO_SLOW (this case happens iff the transfer mode has already been
set on the device by ide-proc.c::set_xfer_rate()) and remove redundant
setting of ->{init,current}_speed.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ide_tune_dma() in amd74xx/via82cxxx driver, this fixes following bugs:
- DMA capability bit not being checked on the device
- DMA blacklist not being checked
- DMA mode being programmed even if drive->autodma == 0
(thus possibly destroying PIO timings)
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_rate_filter() calls from host drivers to IDE core.
* Make ide_rate_filter() static.
* Make 'speed' argument of ->speedproc const.
v2:
* Fix it8213_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix icside, cris-ide, au1xxx-ide, amd74xx, via82cxxx and pmac host drivers
to use ide_rate_filter().
This results in the following modes (from user requests) being clipped down:
- invalid modes (values 0x46-0xFF) [ for all hosts ]
- unsupported by a host UDMA modes [ for hosts which support UDMA]
- all UDMA modes and MWDMA3-4 modes [ for hosts which don't support UDMA ]
- invalid modes (values 0x25-0x39) [ for hosts which don't support UDMA ]
* Host driver specific changes in behavior:
icside:
- no change
cris-ide
- clip unsupported UDMA3-6 modes down
- fix BUG() on trying to set unsupported UDMA3-6 modes
au1xxx-ide/pmac
- clip unsupported UDMA modes down
amd74xx/via82cxxx
- clip unsupported UDMA modes down
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* While at it remove no longer needed checks from pmac.c driver.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ATA_PIO[0-6] defines to <linux/ata.h>.
* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.
* Add PIO masks to host drivers.
<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->host_flags to ide_hwif_t to store ide_pci_device_t.host_flags,
assign it in setup-pci.c:ide_pci_setup_ports().
* Add IDE_HFLAG_PIO_NO_{BLACKLIST,DOWNGRADE} to ide_pci_device_t.host_flags
and teach ide_get_best_pio_mode() about them. Also remove needless
!drive->id check while at it (drive->id is always present).
* Convert amd74xx, via82cxxx and ide-timing.h to use ide_get_best_pio_mode()
and then remove no longer needed ide_find_best_pio_mode().
There should be no functionality changes caused by this patch.
Acked-by: Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.
* Add IDE_HFLAG_SINGLE flag for single channel devices.
* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
and remove no longer needed ide_pci_device_t.channels field.
v2:
* Fix issues noticed by Sergei:
- correct code alignment in scc_pata.c
- s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter. Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.
Next patches add automatic detection of some systems using short cables.
Changes:
* Rename hwif->udma_four to hwif->cbl and make it u8.
* Convert all existing users accordingly (use ATA_CBL_* defines while at it).
* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().
* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
ide-timing.h:
* remove handling of DMA modes from ide_find_best_mode() and rename it to
ide_find_best_pio_mode()
* drop no longer needed "map" argument from ide_find_best_pio_mode()
and delete needless ->id check
* remove no longer needed XFER_SWDMA and XFER_UDMA* defines
au1xxx-ide.c:
* use ide_max_dma_mode() instead of ide_find_best_mode()
* remove needless CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA #ifdef
amd74xx.c:
* store UDMA masks in amd_ide_chip[] and while at it make "base" field
to be u8 instead of unsigned long
* convert the driver to use UDMA masks from amd_ide_chip[]
* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
of ide_find_best_mode()
* delete stale comment from amd74xx_ide_dma_check()
* remove no longer needed AMD_UDMA* defines
via82cxxx.c:
* remove unused DISPLAY_VIA_TIMINGS define
* store UDMA masks in via_isa_bridges[] and while at it make "flags" field
to be u8 instead of u16
* convert the driver to use UDMA masks from via_isa_bridges[]
* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
of ide_find_best_mode()
* remove no longer needed VIA_UDMA* defines
pmac.c:
* use ide_max_dma_mode() instead of ide_find_best_mode()
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
* Driver can't skip programming transfer mode on the device in amd_set_drive()
(similar fix has been applied to via82cxxx driver ages ago).
* While at it remove redundant warning (ide_config_drive_speed() already
produces more valuable one).
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All important information/features should be already available through
sysfs and ioctl interfaces.
Add CONFIG_IDE_PROC_FS (CONFIG_SCSI_PROC_FS rip-off) config option,
disabling it makes IDE driver ~5 kB smaller (on x86-32).
While at it add CONFIG_PROC_FS=n versions of proc_ide_{create,destroy}()
and remove no longer needed #ifdefs.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
-1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
0 when DMA needs to be enabled (== need to call ->ide_dma_on)
1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add support for PATA controllers of MCP67 to amd74xx.c.
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
>From http://marc.theaimsgroup.com/?l=linux-kernel&m=110304128900342&w=2
AMD756 doesn't support host side cable detection. Do disk side only and
don't advice obsolete options.
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Jordan Crouse" <jordan.crouse@amd.com>
The core IDE engine on the CS5536 is the same as the other AMD southbridges,
so unlike the CS5535, we can simply add the appropriate PCI headers to
the existing amd74xx code.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From: Rob Punkunus <rpunkunus@nvidia.com>
Rob Punkunus recently submitted a patch to enable support for MCP51/MCP55 in
the amd74xx driver. This patch was whitespace-corrupted and didn't apply to
2.6.12 since MCP51 support was merged in the 2.6.12-rc series.
Gentoo would like to support this hardware for our upcoming release media, so
I fixed the patch, and here it is :)
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
From: Herbert Xu <herbert@gondor.apana.org.au>
mark the __init section __devinit.
Splitted up from the Debian kernel patch.
Signed-off-by: maximilian attems <janitor@sternwelten.at>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Bartlomiej Zolnierkiewicz
Auke Kok
Peer Chen
Peer Chen
Jörn Engel
Randy Dunlap
Andrew Chew
Rene Herman
Jordan Crouse
Rob Punkunus
Herbert Xu
Andy Currid
Linus Torvalds