linux-stable-rt/arch/arm/mach-ux500/board-mop500.c

227 lines
5.0 KiB
C

/*
* Copyright (C) 2008-2009 ST-Ericsson
*
* Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2, as
* published by the Free Software Foundation.
*
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl022.h>
#include <linux/spi/spi.h>
#include <linux/mfd/ab8500.h>
#include <linux/mfd/tc3589x.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <plat/pincfg.h>
#include <plat/i2c.h>
#include <mach/hardware.h>
#include <mach/setup.h>
#include <mach/devices.h>
#include <mach/irqs.h>
#include "devices-db8500.h"
#include "pins-db8500.h"
#include "board-mop500.h"
#include "board-mop500-regulators.h"
static pin_cfg_t mop500_pins[] = {
/* SSP0 */
GPIO143_SSP0_CLK,
GPIO144_SSP0_FRM,
GPIO145_SSP0_RXD,
GPIO146_SSP0_TXD,
/* I2C */
GPIO147_I2C0_SCL,
GPIO148_I2C0_SDA,
GPIO16_I2C1_SCL,
GPIO17_I2C1_SDA,
GPIO10_I2C2_SDA,
GPIO11_I2C2_SCL,
GPIO229_I2C3_SDA,
GPIO230_I2C3_SCL,
/* SKE keypad */
GPIO153_KP_I7,
GPIO154_KP_I6,
GPIO155_KP_I5,
GPIO156_KP_I4,
GPIO157_KP_O7,
GPIO158_KP_O6,
GPIO159_KP_O5,
GPIO160_KP_O4,
GPIO161_KP_I3,
GPIO162_KP_I2,
GPIO163_KP_I1,
GPIO164_KP_I0,
GPIO165_KP_O3,
GPIO166_KP_O2,
GPIO167_KP_O1,
GPIO168_KP_O0,
/* GPIO_EXP_INT */
GPIO217_GPIO,
/* STMPE1601 IRQ */
GPIO218_GPIO | PIN_INPUT_PULLUP,
};
static struct ab8500_platform_data ab8500_platdata = {
.irq_base = MOP500_AB8500_IRQ_BASE,
.regulator = ab8500_regulators,
.num_regulator = ARRAY_SIZE(ab8500_regulators),
};
static struct resource ab8500_resources[] = {
[0] = {
.start = IRQ_DB8500_AB8500,
.end = IRQ_DB8500_AB8500,
.flags = IORESOURCE_IRQ
}
};
struct platform_device ab8500_device = {
.name = "ab8500-i2c",
.id = 0,
.dev = {
.platform_data = &ab8500_platdata,
},
.num_resources = 1,
.resource = ab8500_resources,
};
static struct pl022_ssp_controller ssp0_platform_data = {
.bus_id = 0,
/* pl022 not yet supports dma */
.enable_dma = 0,
/* on this platform, gpio 31,142,144,214 &
* 224 are connected as chip selects
*/
.num_chipselect = 5,
};
/*
* TC35892
*/
static void mop500_tc35892_init(struct tc3589x *tc3589x, unsigned int base)
{
mop500_sdi_tc35892_init();
}
static struct tc3589x_gpio_platform_data mop500_tc35892_gpio_data = {
.gpio_base = MOP500_EGPIO(0),
.setup = mop500_tc35892_init,
};
static struct tc3589x_platform_data mop500_tc35892_data = {
.block = TC3589x_BLOCK_GPIO,
.gpio = &mop500_tc35892_gpio_data,
.irq_base = MOP500_EGPIO_IRQ_BASE,
};
static struct i2c_board_info mop500_i2c0_devices[] = {
{
I2C_BOARD_INFO("tc3589x", 0x42),
.irq = NOMADIK_GPIO_TO_IRQ(217),
.platform_data = &mop500_tc35892_data,
},
};
#define U8500_I2C_CONTROLLER(id, _slsu, _tft, _rft, clk, _sm) \
static struct nmk_i2c_controller u8500_i2c##id##_data = { \
/* \
* slave data setup time, which is \
* 250 ns,100ns,10ns which is 14,6,2 \
* respectively for a 48 Mhz \
* i2c clock \
*/ \
.slsu = _slsu, \
/* Tx FIFO threshold */ \
.tft = _tft, \
/* Rx FIFO threshold */ \
.rft = _rft, \
/* std. mode operation */ \
.clk_freq = clk, \
.sm = _sm, \
}
/*
* The board uses 4 i2c controllers, initialize all of
* them with slave data setup time of 250 ns,
* Tx & Rx FIFO threshold values as 1 and standard
* mode of operation
*/
U8500_I2C_CONTROLLER(0, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
U8500_I2C_CONTROLLER(1, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
U8500_I2C_CONTROLLER(2, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
U8500_I2C_CONTROLLER(3, 0xe, 1, 1, 100000, I2C_FREQ_MODE_STANDARD);
static void __init mop500_i2c_init(void)
{
db8500_add_i2c0(&u8500_i2c0_data);
db8500_add_i2c1(&u8500_i2c1_data);
db8500_add_i2c2(&u8500_i2c2_data);
db8500_add_i2c3(&u8500_i2c3_data);
}
/* add any platform devices here - TODO */
static struct platform_device *platform_devs[] __initdata = {
};
static void __init mop500_spi_init(void)
{
db8500_add_ssp0(&ssp0_platform_data);
}
static void __init mop500_uart_init(void)
{
db8500_add_uart0();
db8500_add_uart1();
db8500_add_uart2();
}
static void __init u8500_init_machine(void)
{
u8500_init_devices();
nmk_config_pins(mop500_pins, ARRAY_SIZE(mop500_pins));
platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
mop500_i2c_init();
mop500_sdi_init();
mop500_spi_init();
mop500_uart_init();
mop500_keypad_init();
platform_device_register(&ab8500_device);
i2c_register_board_info(0, mop500_i2c0_devices,
ARRAY_SIZE(mop500_i2c0_devices));
}
MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
/* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
.boot_params = 0x100,
.map_io = u8500_map_io,
.init_irq = ux500_init_irq,
/* we re-use nomadik timer here */
.timer = &ux500_timer,
.init_machine = u8500_init_machine,
MACHINE_END