184 lines
6.1 KiB
Plaintext
184 lines
6.1 KiB
Plaintext
|
|
Ext3 Filesystem
|
|
===============
|
|
|
|
ext3 was originally released in September 1999. Written by Stephen Tweedie
|
|
for 2.2 branch, and ported to 2.4 kernels by Peter Braam, Andreas Dilger,
|
|
Andrew Morton, Alexander Viro, Ted Ts'o and Stephen Tweedie.
|
|
|
|
ext3 is ext2 filesystem enhanced with journalling capabilities.
|
|
|
|
Options
|
|
=======
|
|
|
|
When mounting an ext3 filesystem, the following option are accepted:
|
|
(*) == default
|
|
|
|
jounal=update Update the ext3 file system's journal to the
|
|
current format.
|
|
|
|
journal=inum When a journal already exists, this option is
|
|
ignored. Otherwise, it specifies the number of
|
|
the inode which will represent the ext3 file
|
|
system's journal file.
|
|
|
|
noload Don't load the journal on mounting.
|
|
|
|
data=journal All data are committed into the journal prior
|
|
to being written into the main file system.
|
|
|
|
data=ordered (*) All data are forced directly out to the main file
|
|
system prior to its metadata being committed to
|
|
the journal.
|
|
|
|
data=writeback Data ordering is not preserved, data may be
|
|
written into the main file system after its
|
|
metadata has been committed to the journal.
|
|
|
|
commit=nrsec (*) Ext3 can be told to sync all its data and metadata
|
|
every 'nrsec' seconds. The default value is 5 seconds.
|
|
This means that if you lose your power, you will lose,
|
|
as much, the latest 5 seconds of work (your filesystem
|
|
will not be damaged though, thanks to journaling). This
|
|
default value (or any low value) will hurt performance,
|
|
but it's good for data-safety. Setting it to 0 will
|
|
have the same effect than leaving the default 5 sec.
|
|
Setting it to very large values will improve
|
|
performance.
|
|
|
|
barrier=1 This enables/disables barriers. barrier=0 disables it,
|
|
barrier=1 enables it.
|
|
|
|
orlov (*) This enables the new Orlov block allocator. It's enabled
|
|
by default.
|
|
|
|
oldalloc This disables the Orlov block allocator and enables the
|
|
old block allocator. Orlov should have better performance,
|
|
we'd like to get some feedback if it's the contrary for
|
|
you.
|
|
|
|
user_xattr (*) Enables POSIX Extended Attributes. It's enabled by
|
|
default, however you need to confifure its support
|
|
(CONFIG_EXT3_FS_XATTR). This is neccesary if you want
|
|
to use POSIX Acces Control Lists support. You can visit
|
|
http://acl.bestbits.at to know more about POSIX Extended
|
|
attributes.
|
|
|
|
nouser_xattr Disables POSIX Extended Attributes.
|
|
|
|
acl (*) Enables POSIX Access Control Lists support. This is
|
|
enabled by default, however you need to configure
|
|
its support (CONFIG_EXT3_FS_POSIX_ACL). If you want
|
|
to know more about ACLs visit http://acl.bestbits.at
|
|
|
|
noacl This option disables POSIX Access Control List support.
|
|
|
|
reservation
|
|
|
|
noreservation
|
|
|
|
resize=
|
|
|
|
bsddf (*) Make 'df' act like BSD.
|
|
minixdf Make 'df' act like Minix.
|
|
|
|
check=none Don't do extra checking of bitmaps on mount.
|
|
nocheck
|
|
|
|
debug Extra debugging information is sent to syslog.
|
|
|
|
errors=remount-ro(*) Remount the filesystem read-only on an error.
|
|
errors=continue Keep going on a filesystem error.
|
|
errors=panic Panic and halt the machine if an error occurs.
|
|
|
|
grpid Give objects the same group ID as their creator.
|
|
bsdgroups
|
|
|
|
nogrpid (*) New objects have the group ID of their creator.
|
|
sysvgroups
|
|
|
|
resgid=n The group ID which may use the reserved blocks.
|
|
|
|
resuid=n The user ID which may use the reserved blocks.
|
|
|
|
sb=n Use alternate superblock at this location.
|
|
|
|
quota Quota options are currently silently ignored.
|
|
noquota (see fs/ext3/super.c, line 594)
|
|
grpquota
|
|
usrquota
|
|
|
|
|
|
Specification
|
|
=============
|
|
ext3 shares all disk implementation with ext2 filesystem, and add
|
|
transactions capabilities to ext2. Journaling is done by the
|
|
Journaling block device layer.
|
|
|
|
Journaling Block Device layer
|
|
-----------------------------
|
|
The Journaling Block Device layer (JBD) isn't ext3 specific. It was
|
|
design to add journaling capabilities on a block device. The ext3
|
|
filesystem code will inform the JBD of modifications it is performing
|
|
(Call a transaction). the journal support the transactions start and
|
|
stop, and in case of crash, the journal can replayed the transactions
|
|
to put the partition on a consistent state fastly.
|
|
|
|
handles represent a single atomic update to a filesystem. JBD can
|
|
handle external journal on a block device.
|
|
|
|
Data Mode
|
|
---------
|
|
There's 3 different data modes:
|
|
|
|
* writeback mode
|
|
In data=writeback mode, ext3 does not journal data at all. This mode
|
|
provides a similar level of journaling as XFS, JFS, and ReiserFS in its
|
|
default mode - metadata journaling. A crash+recovery can cause
|
|
incorrect data to appear in files which were written shortly before the
|
|
crash. This mode will typically provide the best ext3 performance.
|
|
|
|
* ordered mode
|
|
In data=ordered mode, ext3 only officially journals metadata, but it
|
|
logically groups metadata and data blocks into a single unit called a
|
|
transaction. When it's time to write the new metadata out to disk, the
|
|
associated data blocks are written first. In general, this mode
|
|
perform slightly slower than writeback but significantly faster than
|
|
journal mode.
|
|
|
|
* journal mode
|
|
data=journal mode provides full data and metadata journaling. All new
|
|
data is written to the journal first, and then to its final location.
|
|
In the event of a crash, the journal can be replayed, bringing both
|
|
data and metadata into a consistent state. This mode is the slowest
|
|
except when data needs to be read from and written to disk at the same
|
|
time where it outperform all others mode.
|
|
|
|
Compatibility
|
|
-------------
|
|
|
|
Ext2 partitions can be easily convert to ext3, with `tune2fs -j <dev>`.
|
|
Ext3 is fully compatible with Ext2. Ext3 partitions can easily be
|
|
mounted as Ext2.
|
|
|
|
External Tools
|
|
==============
|
|
see manual pages to know more.
|
|
|
|
tune2fs: create a ext3 journal on a ext2 partition with the -j flags
|
|
mke2fs: create a ext3 partition with the -j flags
|
|
debugfs: ext2 and ext3 file system debugger
|
|
|
|
References
|
|
==========
|
|
|
|
kernel source: file:/usr/src/linux/fs/ext3
|
|
file:/usr/src/linux/fs/jbd
|
|
|
|
programs: http://e2fsprogs.sourceforge.net
|
|
|
|
useful link:
|
|
http://www.zip.com.au/~akpm/linux/ext3/ext3-usage.html
|
|
http://www-106.ibm.com/developerworks/linux/library/l-fs7/
|
|
http://www-106.ibm.com/developerworks/linux/library/l-fs8/
|