63 lines
2.5 KiB
ReStructuredText
63 lines
2.5 KiB
ReStructuredText
|
.. SPDX-License-Identifier: GPL-2.0-or-later
|
||
|
|
|
||
|
|
Kernel driver nzxt-smart2
|
||
|
|
=========================
|
||
|
|
|
||
|
|
Supported devices:
|
||
|
|
|
||
|
|
- NZXT RGB & Fan controller
|
||
|
|
- NZXT Smart Device v2
|
||
|
|
|
||
|
|
Description
|
||
|
|
-----------
|
||
|
|
|
||
|
|
This driver implements monitoring and control of fans plugged into the device.
|
||
|
|
Besides typical speed monitoring and PWM duty cycle control, voltage and current
|
||
|
|
is reported for every fan.
|
||
|
|
|
||
|
|
The device also has two connectors for RGB LEDs; support for them isn't
|
||
|
|
implemented (mainly because there is no standardized sysfs interface).
|
||
|
|
|
||
|
|
Also, the device has a noise sensor, but the sensor seems to be completely
|
||
|
|
useless (and very imprecise), so support for it isn't implemented too.
|
||
|
|
|
||
|
|
Usage Notes
|
||
|
|
-----------
|
||
|
|
|
||
|
|
The device should be autodetected, and the driver should load automatically.
|
||
|
|
|
||
|
|
If fans are plugged in/unplugged while the system is powered on, the driver
|
||
|
|
must be reloaded to detect configuration changes; otherwise, new fans can't
|
||
|
|
be controlled (`pwm*` changes will be ignored). It is necessary because the
|
||
|
|
device has a dedicated "detect fans" command, and currently, it is executed only
|
||
|
|
during initialization. Speed, voltage, current monitoring will work even without
|
||
|
|
reload. As an alternative to reloading the module, a userspace tool (like
|
||
|
|
`liquidctl`_) can be used to run "detect fans" command through hidraw interface.
|
||
|
|
|
||
|
|
The driver coexists with userspace tools that access the device through hidraw
|
||
|
|
interface with no known issues.
|
||
|
|
|
||
|
|
.. _liquidctl: https://github.com/liquidctl/liquidctl
|
||
|
|
|
||
|
|
Sysfs entries
|
||
|
|
-------------
|
||
|
|
|
||
|
|
======================= ========================================================
|
||
|
|
fan[1-3]_input Fan speed monitoring (in rpm).
|
||
|
|
curr[1-3]_input Current supplied to the fan (in milliamperes).
|
||
|
|
in[0-2]_input Voltage supplied to the fan (in millivolts).
|
||
|
|
pwm[1-3] Controls fan speed: PWM duty cycle for PWM-controlled
|
||
|
|
fans, voltage for other fans. Voltage can be changed in
|
||
|
|
9-12 V range, but the value of the sysfs attribute is
|
||
|
|
always in 0-255 range (1 = 9V, 255 = 12V). Setting the
|
||
|
|
attribute to 0 turns off the fan completely.
|
||
|
|
pwm[1-3]_enable 1 if the fan can be controlled by writing to the
|
||
|
|
corresponding pwm* attribute, 0 otherwise. The device
|
||
|
|
can control only the fans it detected itself, so the
|
||
|
|
attribute is read-only.
|
||
|
|
pwm[1-3]_mode Read-only, 1 for PWM-controlled fans, 0 for other fans
|
||
|
|
(or if no fan connected).
|
||
|
|
update_interval The interval at which all inputs are updated (in
|
||
|
|
milliseconds). The default is 1000ms. Minimum is 250ms.
|
||
|
|
======================= ========================================================
|