original_kernel/drivers/clk/at91/Makefile

#
# Makefile for at91 specific clk
#

obj-y += pmc.o
obj-y += clk-main.o clk-pll.o clk-plldiv.o clk-master.o
obj-y += clk-system.o clk-peripheral.o

obj-$(CONFIG_AT91_PROGRAMMABLE_CLOCKS)	+= clk-programmable.o
obj-$(CONFIG_HAVE_AT91_UTMI)		+= clk-utmi.o
obj-$(CONFIG_HAVE_AT91_USB_CLK)		+= clk-usb.o
clk: at91: add PMC base support This patch adds at91 PMC (Power Management Controller) base support. All at91 clocks managed by the PMC unit will use this framework. This framework provides the following fonctionalities: - define a new struct at91_pmc to hide PMC internals (lock, PMC memory mapping, irq domain, ...) - read/write helper functions (pmc_read/write) to access PMC registers - lock/unlock helper functions (pmc_lock/unlock) to lock/unlock access to pmc registers - a new irq domain and its associated irq chip to request PMC specific interrupts (useful for clk prepare callbacks) The PMC unit is declared as a dt clk provider (CLK_OF_DECLARE), and every clk using this framework will declare a table of of_at91_clk_init_cb_t and add it to the pmc_clk_ids table. When the pmc dt clock setup function is called (by of_clk_init function), it triggers the registration of every supported child clk (those matching the definitions in pmc_clk_ids). This patch copies at91_pmc_base (memory mapping) and at91sam9_idle (function) from arch/arm/mach-at91/clock.c (which is not compiled if COMMON_CLK_AT91 is enabled). Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-12-02 22:07:02 +08:00			`#`
			`# Makefile for at91 specific clk`
			`#`

			`obj-y += pmc.o`
clk: at91: add PMC master clock This patch adds new at91 master clock implementation using common clk framework. The master clock layout describe the MCKR register layout. There are 2 master clock layouts: - at91rm9200 - at91sam9x5 Master clocks are given characteristics: - min/max clock output rate These characteristics are checked during rate change to avoid over/underclocking. These characteristics are described in atmel's SoC datasheet in "Electrical Characteristics" paragraph. Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-10-11 16:51:23 +08:00			`obj-y += clk-main.o clk-pll.o clk-plldiv.o clk-master.o`
clk: at91: add PMC peripheral clocks This patch adds new at91 peripheral clock implementation using common clk framework. Almost all peripherals provided by at91 SoCs need a clock to work properly. This clock is enabled/disabled using PCER/PCDR resgisters. Each peripheral is given an id (see atmel's datasheets) which is used to define and reference peripheral clocks. Some new SoCs (at91sam9x5 and sama5d3) provide a new register (PCR) where you can configure the peripheral clock as a division of the master clock. This will help reducing the peripherals power comsumption. Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-10-11 17:44:36 +08:00			`obj-y += clk-system.o clk-peripheral.o`
clk: at91: add PMC programmable clocks This patch adds new at91 programmable clocks implementation using common clk framework. A programmable clock is a clock which can be exported on a given pin to clock external devices. Each programmable clock is given an id (from 0 to 8). The number of available programmable clocks depends on the SoC you're using. Programmable clock driver only implements the clock setting (clock rate and parent setting). It must be chained to a system clock in order to enable/disable the generated clock. The PCKX pins used to output the clock signals must be assigned to the appropriate peripheral (see atmel's datasheets). Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-10-11 17:57:04 +08:00
			`obj-$(CONFIG_AT91_PROGRAMMABLE_CLOCKS) += clk-programmable.o`
clk: at91: add PMC utmi clock This adds new at91 utmi clock implementation using common clk framework. This clock is a pll with a fixed factor (x40). It is used as a source for usb clock. Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-10-11 18:22:06 +08:00			`obj-$(CONFIG_HAVE_AT91_UTMI) += clk-utmi.o`
clk: at91: add PMC usb clock This patch adds new at91 usb clock implementation using common clk framework. This clock is used to clock usb ports (ohci, ehci and udc). Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> 2013-10-18 00:55:41 +08:00			`obj-$(CONFIG_HAVE_AT91_USB_CLK) += clk-usb.o`