This patch initializes the platform data to enable 4-bit
ecc support on DA850/OMAP-L138.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On DA850/OMAP-L138, NOR flash partition was starting from offset
ZERO erasing the UBL and u-boot when the complete NOR is erased.
This patch moves the start of the partition to 512K, after the
bootloaders and u-boot env variables.
This patch also creates a new partition on NOR Flash to store
Linux kernel image.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP-L138 adds a second SYSCFG region having useful functionality
like deep sleep, pull up/down control and SATA clock stop.
This patch makes provision for accessing registers from second
SYSCFG region in da8xx code.
Note that OMAP-L137 has a single SYSCFG region.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add the platform specific callback to control LCD panel and backlight
power.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include high speed capabilities in MMC/SD platform data
for DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When kernel is built with CONFIG_DEBUG_SECTION_MISMATCH=y
option, using da8xx_omapl_defconfig, some warnings are
observed:
WARNING: vmlinux.o(.text+0xc2a4): Section mismatch in reference
from the function da850_evm_setup_nor_nand() to the variable
.init.data:da850_nand_pins
The function da850_evm_setup_nor_nand() references
the variable __initdata da850_nand_pins.
This is often because da850_evm_setup_nor_nand lacks a __initdata
annotation or the annotation of da850_nand_pins is wrong.
This patch fixes such warnings.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Eliminate the static function declaration by rearranging
data in da850/omap-l138 board file.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There are multiple steps in configuring the EMAC to MII or RMII mode.
Current code implements them using multiple checks.
Consolidate the multiple checks into a single if construct.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Implement autodetection of RMII PHY by shifting the decision
to use the RMII PHY to da850_evm_ui_expander_setup() from
da850_evm_init() earlier.
Without this patch, selecting RMII PHY in the UI expander menu
will make the MII PHY unusable even though UI board is not
connected.
The actual configuration and registration of the EMAC device
is delayed to device_initcall() so it happens after the UI card
detection is complete.
A side effect of this patch is the removal of a voilation of
Documentation/SubmittingPatches section 2.2 in function
da850_evm_init()
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There have accumulated quite a lot of them after the code reorganizations...
In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 EVM has a RMII Ethernet PHY on the UI daughter card. The PHY
is enabled by proper programming of the IO Expander (TCA6416) ports. Also for
RMII PHY to work, the MDIO clock of MII PHY has to be disabled since both the
PHYs have the same address. This is done via the GPIO2[6] pin. This patch adds
support for RMII PHY.
This patch also adds a menuconfig option to select one or no peripheral
connected to expander. Currently, sub-options in this menu are RMII and no
peripheral.This menuconfig option is similar to the one present for UI card on
DA830/OMAP-L137 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 EVM can be connected to an UI card which has various
peripherals on it.The UI card has TCA6416 expander which can be probed
to check whether the UI card is connected or not. If the UI card is
connected, setup NOR and NAND devices. This is done via the expander
setup callback.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for using the TPS65070 PMIC found
on the DA850/OMAP-L138 EVM.
It defines the power rail consumer mapping and registers the
the I2C based PMIC as a board device.
The power rail constraints are derived from the maxmimum and
minimum recommended operating condition values of the respective
consumers derived from section 5.2 of the OMAP-L138 datasheet.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On the latest DA850/OMAP-L138 EVM (Beta) the GPIO pin
number of LCD panel power has changed. This patch takes
care of this change. Software will support only Beta
versions of DA850/OMAP-L138 EVM.
In the process, add the missing entry for data pin 0
and remove the GPIO specific pins from da850_lcdcntl_pins
structure. EVM specific muxing for LCD is being done in the
board file now.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add RTC support for the da830/omap-l137 and da850/omap-l138
SoC's by leveraging existing the rtc-omap driver.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the Sharp LCD035Q3DG01 graphical LCD. This
requires a minor interface change to da8xx_register_lcdc()
so that the board code can pass in the platform_data which
describes the lcd controller that's to be used.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For consistency with existing code, change the name of
da8xx_init_mcasp() to da8xx_register_mcasp().
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested on DM6446, DM355, DM6447, DA850 EVMs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On DA850/OMAP-L138 EVM, MMC/SD and NOR Flash share
some of the AEMIF pins. This patch prints out a warning
during booting, if both MMC/SD and NOR Flash are enabled
in kernel menuconfig.
If both MMC/SD and NOR Flash are enabled, only MMC/SD
will work correctly.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data for the 8MB NOR flash
found on da850/omap-l138 EVM. Both NOR and NAND can
co-exist on da850/omap-l138 as they are using different
chip selects.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data for the 512MB NAND Flash
found on DA850/OMAP-L138 EVM. Currently it supports
only 1-bit ECC.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There are two instances of MMC/SD on da850/omap-l138.
Connector for the first instance is available on the
EVM. This patch adds support for this instance.
This patch also adds support for card detect and write
protect switches on da850/omap-l138 EVM.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform support for the graphic display
(Sharp LK043T1DG01) found on DA850/OMAP-L138 based EVM.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Define resources for McASP used on DA850/OMAP-L138 EVM, add platform
device defintion and Pin Mux configurations.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Ethernet Media Access Controller (EMAC) on da850/omap-l138
supports 10/100 Mbps operation. It also supports Media
Independent Interface (MII) and Reduced Media Independent
Interface (RMII) to physical layer (PHY).
Phy which supports MII is present on the DA850/OMAP-L138
base board and Phy supporting RMII is present on the
UI card. This patch adds support only for the MII Phy.
Support for RMII Phy will be added later.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the DA850/OMAP-L138 Evaluation Module (EVM)
from TI. The EVM has User Interface (UI) card which contains
various devices. This UI card can be connected to the base
board. Support for all the devices on the UI card and ones on
the EVM will be added in subsequent patches.
The EVM schematics are not available publicly yet; but should
be available soon.
A new defconfig for this board has been added mainly because
the DA830/OMAP-L137 defconfig forces writethrough cache mode
which is not required on DA850/OMAP-L138.
This patch has been boot tested on DA850/OMAP-L138 EVM
using ramdisk as filesystem.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Sekhar Nori
Sudhakar Rajashekhara
Chaithrika U S
Sergei Shtylyov
Mark A. Greer