Fix build breakage due to the following commits:
Commit bd5f12a247
ARM: 7042/3: mach-ep93xx: break out GPIO driver specifics
Commit 257af9f972
ARM: 7041/1: gpio-ep93xx: hookup the to_irq callback in the driver
The vision_ep9307 machine uses the ep93xx build-in gpios and needs to
include <mach/gpio-ep93xx.h> to pickup the defines.
The gpio_to_irq() call is now a callback to the gpio-ep93xx.c driver
and cannot be used as a constant initializer for the .irq member of
struct i2c_board_info.
Signed-off-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These are no longer required since a 'parent' pointer is now
passed to each registering device.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
At the request of Arnd Bergmann this patch moves all SoC
platform devices found in sysfs from /sys/devices/platform to
/sys/devices/soc<SoCNum>/. It is believed as the devices are
SoC specific and a /sys/devices/soc node has recently
become available, that this would be a more appropriate place to
display the data.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we make use of the new System-On-Chip bus driver to export
vital SoC information out to userspace via sysfs. This patch
provides a data structure of strings to populate the base
nodes found in:
/sys/devices/soc[0|1|2|...]/[family|machine|revision|soc_id].
It also adds one more node as requested by ST-Ericsson.
'process' depicts the way in which the silicon was manufactured.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch provides a means for any device within ux500
platform code to allocate its own parent. This is particularly
prudent with the introduction of /sys/devices/socX, as a
device can now proclaim to be integral part of an SoC, rather
than a more generic platform device. Latter patches make good
use of this functionality.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix the newly-SACKed range to be the range of newly-shifted bytes.
Previously - since 832d11c5cd -
tcp_shifted_skb() incorrectly called tcp_sacktag_one() with the start
and end sequence numbers of the skb it passes in set to the range just
beyond the range that is newly-SACKed.
This commit also removes a special-case adjustment to lost_cnt_hint in
tcp_shifted_skb() since the pre-existing adjustment of lost_cnt_hint
in tcp_sacktag_one() now properly handles this things now that the
correct start sequence number is passed in.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows callers of tcp_sacktag_one() to pass in sequence
ranges that do not align with skb boundaries, as tcp_shifted_skb()
needs to do in an upcoming fix in this patch series.
In fact, now tcp_sacktag_one() does not need to depend on an input skb
at all, which makes its semantics and dependencies more clear.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'v3.3-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (2 commits)
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
Linux 3.3-rc3
This includes an update to the v3.3-rc3 release from v3.3-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When eSDHC module is enabled on P5020/P3041/P2041/P1010 with eSDHC
version 2.3, there is following errors:
mmc0: Timeout waiting for hardware interrupt.
mmc0: error -110 whilst initialising SD card
mmc0: Unexpected interrupt 0x02000000.
mmc0: Timeout waiting for hardware interrupt.
mmc0: error -110 whilst initialising SD card
mmc0: Unexpected interrupt 0x02000000.
It is because eSDHC controller has different bit setting for PROCTL
register at 0x28 comparing SD specification.
This patch sets DMAS bits correctly for byte operation and does not
change the default value of other field of PROCTL register.
For other FSL chips, such as MPC8536/P2020, PROCTL[DMAS]
bits are reserved and even if they are set to wrong bits, it will not
take effective.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Says Jens:
"Time to push off some of the pending items. I really wanted to wait
until we had the regression nailed, but alas it's not quite there yet.
But I'm very confident that it's "just" a missing expire on exit, so
fix from Tejun should be fairly trivial. I'm headed out for a week on
the slopes.
- Killing the barrier part of mtip32xx. It doesn't really support
barriers, and it doesn't need them (writes are fully ordered).
- A few fixes from Dan Carpenter, preventing overflows of integer
multiplication.
- A fixup for loop, fixing a previous commit that didn't quite solve
the partial read problem from Dave Young.
- A bio integer overflow fix from Kent Overstreet.
- Improvement/fix of the door "keep locked" part of the cdrom shared
code from Paolo Benzini.
- A few cfq fixes from Shaohua Li.
- A fix for bsg sysfs warning when removing a file it did not create
from Stanislaw Gruszka.
- Two fixes for floppy from Vivek, preventing a crash.
- A few block core fixes from Tejun. One killing the over-optimized
ioc exit path, cleaning that up nicely. Two others fixing an oops
on elevator switch, due to calling into the scheduler merge check
code without holding the queue lock."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix lockdep warning on io_context release put_io_context()
relay: prevent integer overflow in relay_open()
loop: zero fill bio instead of return -EIO for partial read
bio: don't overflow in bio_get_nr_vecs()
floppy: Fix a crash during rmmod
floppy: Cleanup disk->queue before caling put_disk() if add_disk() was never called
cdrom: move shared static to cdrom_device_info
bsg: fix sysfs link remove warning
block: don't call elevator callbacks for plug merges
block: separate out blk_rq_merge_ok() and blk_try_merge() from elevator functions
mtip32xx: removed the irrelevant argument of mtip_hw_submit_io() and the unused member of struct driver_data
block: strip out locking optimization in put_io_context()
cdrom: use copy_to_user() without the underscores
block: fix ioc locking warning
block: fix NULL icq_cache reference
block,cfq: change code order
11a3122f6c "block: strip out locking optimization in put_io_context()"
removed ioc_lock depth lockdep annoation along with locking
optimization; however, while recursing from put_io_context() is no
longer possible, ioc_release_fn() may still end up putting the last
reference of another ioc through elevator, which wlil grab ioc->lock
triggering spurious (as the ioc is always different one) A-A deadlock
warning.
As this can only happen one time from ioc_release_fn(), using non-zero
subclass from ioc_release_fn() is enough. Use subclass 1.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Quoth David:
1) GRO MAC header comparisons were ethernet specific, breaking other
link types. This required a multi-faceted fix to cure the originally
noted case (Infiniband), because IPoIB was lying about it's actual
hard header length. Thanks to Eric Dumazet, Roland Dreier, and
others.
2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
From Anisse Astier.
3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.
4) ipv4 TCP reset generation needs to respect any network interface
binding from the socket, otherwise route lookups might give a
different result than all the other segments received. From Shawn
Lu.
5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
Graf.
6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.
7) Revert skge PCI mapping changes that are causing crashes for some
folks, from Stephen Hemminger.
8) IPV4 route lookups fill in the wildcarded fields of the given flow
lookup key passed in, which is fine most of the time as this is
exactly what the caller's want. However there are a few cases that
want to retain the original flow key values afterwards, so handle
those cases properly. Fix from Julian Anastasov.
9) IGB/IXGBE VF lookup bug fixes from Greg Rose.
10) Properly null terminate filename passed to ethtool flash device
method, from Ben Hutchings.
11) S3 resume fix in via-velocity from David Lv.
12) Fix double SKB free during xmit failure in CAIF, from Dmitry
Tarnyagin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
netprio_cgroup: don't allocate prio table when a device is registered
netprio_cgroup: fix an off-by-one bug
bna: fix error handling of bnad_get_flash_partition_by_offset()
isdn: type bug in isdn_net_header()
net: Make qdisc_skb_cb upper size bound explicit.
ixgbe: ethtool: stats user buffer overrun
ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
ixgbe: do not update real num queues when netdev is going away
ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
ixgbe: Fix case of Tx Hang in PF with 32 VFs
ixgbe: fix vf lookup
igb: fix vf lookup
e1000: add dropped DMA receive enable back in for WoL
gro: more generic L2 header check
IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
net: enable TC35815 for MIPS again
...
During test busn_res allocation with cardbus, found pci card removal is not
working anymore, and it turns out it is broken by:
|commit 79cc9601c3
|Date: Tue Nov 22 21:06:53 2011 -0800
|
| PCI: Only call pci_stop_bus_device() one time for child devices at remove
The above changed the behavior of pci_remove_behind_bridge that
yenta_cardbus depended on. So restore the old behavoir of
pci_remove_behind_bridge (which requires stopping and removing of all
devices) by:
1. rename pci_remove_behind_bridge to __pci_remove_behind_bridge, and let
__pci_remove_bus_device() call it instead.
2. add pci_stop_behind_bridge that will stop devices behind a bridge
3. add back pci_remove_behind_bridge that will stop and remove devices
under bridge.
-v2: update commit description a little bit.
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.
Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.
This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a bug which introduced by commit ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the netprio_cgroup module is not loaded, net_prio_subsys_id
is -1, and so sock_update_prioidx() accesses cgroup_subsys array
with negative index subsys[-1].
Make the code resembles cls_cgroup code, which is bug free.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
So we delay the allocation till the priority is set through cgroup,
and this makes skb_update_priority() faster when it's not set.
This also eliminates an off-by-one bug similar with the one fixed
in the previous patch.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
# mount -t cgroup xxx /mnt
# mkdir /mnt/tmp
# cat /mnt/tmp/net_prio.ifpriomap
lo 0
eth0 0
virbr0 0
# echo 'lo 999' > /mnt/tmp/net_prio.ifpriomap
# cat /mnt/tmp/net_prio.ifpriomap
lo 999
eth0 0
virbr0 4101267344
We got weired output, because we exceeded the boundary of the array.
We may even crash the kernel..
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For an SRIOV device, PCI_SRIOV_SYS_PGSIZE should be set before
the PCI_SRIOV_BAR are queried. The sys pagesize defaults to 4k,
so this change is required on powerpc box with 64k base page size.
This is a regression caused due to moving SRIOV init to sriov_enable().
| commit afd24ece5c
| Author: Ram Pai <linuxram@us.ibm.com>
| PCI: delay configuration of SRIOV capability
| The SRIOV capability, namely page size and total_vfs of a device are
| configured during enumeration phase of the device. This can potentially
| interfere with the PCI operations of the platform, if the IOV capability
| of the device is not enabled.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This change applies the required documentation for each new
attribute recenty added by the new System-On-Chip (SoC)
information export bus driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Traditionally, any System-on-Chip based platform creates a flat list
of platform_devices directly under /sys/devices/platform.
In order to give these some better structure, this introduces a new
bus type for soc_devices that are registered with the new
soc_device_register() function. All devices that are on the same
chip should then be registered as child devices of the soc device.
The soc bus also exports a few standardised device attributes which
allow user space to query the specific type of soc.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes PCI device detection on IBM xSeries IBM 3850 M2 / x3950 M2
when using ACPI resources (_CRS).
This is default, a manual workaround (without this patch)
would be pci=nocrs boot param.
V2: Add dev_warn if the workaround is hit. This should reveal
how common such setups are (via google) and point to possible
problems if things are still not working as expected.
-> Suggested by Jan Beulich.
Cc: stable@vger.kernel.org
Tested-by: garyhade@us.ibm.com
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stop reusing dquots from the freelist when allocating new ones directly, and
implement a shrinker that actually follows the specifications for the
interface. The shrinker implementation is still highly suboptimal at this
point, but we can gradually work on it.
This also fixes an bug in the previous lock ordering, where we would take
the hash and dqlist locks inside of the freelist lock against the normal
lock ordering. This is only solvable by introducing the dispose list,
and thus not when using direct reclaim of unused dquots for new allocations.
As a side-effect the quota upper bound and used to free ratio values in
/proc/fs/xfs/xqm are set to 0 as these values don't make any sense in the
new world order.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/radeon: do not continue after error from r600_ib_test
drivers/gpu/drm/drm_ioc32.c: initialize all fields
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix double start/stop in x86_pmu_start()
perf evsel: Fix an issue where perf report fails to show the proper percentage
perf tools: Fix prefix matching for kernel maps
perf tools: Fix perf stack to non executable on x86_64
perf: Remove deprecated WARN_ON_ONCE()
Current code takes wrong parameter while calling max8649_list_voltage.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
"subbuf_size" and "n_subbufs" come from the user and they need to be
capped to prevent an integer overflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On OMAP2420-based systems, the PM code ignores the state of the UART
functional clocks when determining what idle state to enter. This
breaks the serial port now that the UART driver's clock behavior can
be controlled via the PM autosuspend timeout.
To fix, remove the special-case idle handling for the UARTs in the
OMAP2420/2430 PM idle code added by commit
4af4016c53 ("OMAP3: PM: UART: disable
clocks when idle and off-mode support").
Tested on Nokia N800. This patch is a collaboration between Tony
Lindgren <tony@atomide.com> and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch "ARM: orion: Consolidate USB platform setup code.", commit
4fcd3f374a broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.
Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.
Version 2: Rebase to v3.3-rc2.
Reported-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Patchset "ARM: orion: Refactor the MPP code common in the orion
platform" broke at least Orion5x based platforms. These platforms have
pins configured as GPIO when the selector is not 0x0. However the
common code assumes the selector is always 0x0 for a GPIO lines. It
then ignores the GPIO bits in the MPP definitions, resulting in that
Orion5x machines cannot correctly configure there GPIO lines.
The Fix removes the assumption that the selector is always 0x0.
In order that none GPIO configurations are correctly blocked,
Kirkwood and mv78xx0 MPP definitions are corrected to only set the
GPIO bits for GPIO configurations.
This third version, which does not contain any whitespace changes,
and is rebased on v3.3-rc2.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since mc13xxx-regulator-core.c and the actual drivers can get built
into seperate modules, you have to export the DT support symbols
"mc13xxx_get_num_regulators_dt" and "mc13xxx_parse_regulators_dt"
otherwise the allmodconfig build fails on sparc64.
[Updated the subject; the same thing was previously reported and fixed
in -next but for some reason nobody noticed for some considerable time
after the issue was introduced -- broonie]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KZgACgkQMUfUDdst+yk0HgCeIdU3VTWqdxZDXp3G1sFIXZ1b
47YAnRAMAar+/aLaNhqGrcz7aa5y2cUU
=8sr8
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Serial/TTY fixes for the 3.3-rc3 tree
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
m32r: relocate drivers back out of 8250 dir
tty: fix a build failure on sparc
serial: samsung: Add support for EXYNOS5250
serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KLYACgkQMUfUDdst+ykhiwCg2ctSu4umygA1ErAedAA+sJkv
psYAn20OZQDyuBcBAIzL2L+Y/BUz8bXt
=xvyx
-----END PGP SIGNATURE-----
Merge tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Staging tree patches for 3.3-rc3
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
staging: pohmelfs: remove drivers/staging/pohmelfs
staging: android/ram_console: Don't build on arches w/o ioremap
staging: r8712u: Use asynchronous firmware loading
staging: usbip: fix to prevent potentially using uninitialized spinlock
staging: r8712u: Fix problem when CONFIG_R8712_AP is set
staging: tidspbridge: fix incorrect free to drv_datap
staging: tidspbridge: fix bridge_open memory leaks
staging: android: lowmemorykiller: Don't wait more than one second for a process to die
MAINTAINERS: staging: iio: add iio information
staging: zcache: fix serialization bug in zv stats
staging: fix go7007-usb license
Staging: android: binder: Fix crashes when sharing a binder file between processes
Staging: android: Remove pmem driver
Staging: asus_oled: fix NULL-ptr crash on unloading
Staging: asus_oled: fix image processing
Staging: android: binder: Don't call dump_stack in binder_vma_open
staging: r8712u: Add new Sitecom UsB ID
zcache: Set SWIZ_BITS to 8 to reduce tmem bucket lock contention.
zcache: fix deadlock condition
staging: drm/omap: fix locking issue
...
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80J1cACgkQMUfUDdst+ylYfgCcClIeUw4njh3Tup9BpRrdBprr
fBsAoLKKhaZDsnma85PJRDAvtM2guoi7
=0TZ9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Driver core fixes for the 3.3-rc3 tree.
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: cpu: fix kobject warning when hotplugging a cpu
ACPI: remove duplicated lines of merging problems with acpi_processor_add
docbook: fix fatal errors in device-drivers docbook and add DMA Management section
drivers/base/memory.c: fix memory_dev_init() long delay
driver core: cpu: remove kernel warning when removing a cpu
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80HSAACgkQMUfUDdst+ymFsQCghwKbV9B9z5fgUXYwFQJ/pD2j
GhsAn3J2mhhHN/vtSPQAN9Vu59Xb/tCi
=VZaE
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Minor char-misc fixes for 3.3-rc3
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mmc: cb710 core: Add missing spin_lock_init for irq_lock of struct cb710_chip
cs5535-mfgpt: don't call __init function from __devinit
vmw_balloon: fix for a -Wuninitialized warning
drivers: misc: Remove MISC_DEVICES config option
c2port: fix build error for duramar2150 due to missing header.
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80Ki4ACgkQMUfUDdst+ymp3wCfUG2LtQOC2qpzpnl1bcivSA18
11gAn09DbcldfH4k12HyCr7PuBnjILQh
=vfEv
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB fixes for 3.3-rc3
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbserial: add new PID number (0xa951) to the ftdi driver
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
usb: musb: fix a build error on mips
uwb & wusb & usb wireless controllers: fix kconfig error & build errors
usb: Skip PCI USB quirk handling for Netlogic XLP
powerpc/usb: fix issue of CPU halt when missing USB PHY clock
usb: otg: mv_otg: Add dependence
usb: host: Distinguish Kconfig text for Freescale controllers
USB: add new zte 3g-dongle's pid to option.c
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
USB: qcserial: don't enable autosuspend
USB: qcserial: add several new serial devices
usb: otg: mv_otg: Add dependence
usb: gadget: zero: fix bug in loopback autoresume handling
The current error handling doesn't work because we flash_part is a u32
so the checks for negative error codes don't work. I considered making
things signed but I don't know the hardware enough to say if that's a
problem. Really, we don't use the error codes so just returning zero
for all problems is fine.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use len to store the return value from eth_header(). eth_header()
can return -ETH_HLEN (-14). We want to pass this back instead of
truncating it to 65522 and returning that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes problem where caller would think routine succeeded when it failed
leading to divide by zero panic.
Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
read_lock(&tpt_trig->trig.leddev_list_lock) is accessed via the path
ieee80211_open (->) ieee80211_do_open (->) ieee80211_mod_tpt_led_trig
(->) ieee80211_start_tpt_led_trig (->) tpt_trig_timer before initializing
it.
the intilization of this read/write lock happens via the path
ieee80211_led_init (->) led_trigger_register, but we are doing
'ieee80211_led_init' after 'ieeee80211_if_add' where we
register netdev_ops.
so we access leddev_list_lock before initializing it and causes the
following bug in chrome laptops with AR928X cards with the following
script
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
BUG: rwlock bad magic on CPU#1, wpa_supplicant/358, f5b9eccc
Pid: 358, comm: wpa_supplicant Not tainted 3.0.13 #1
Call Trace:
[<8137b9df>] rwlock_bug+0x3d/0x47
[<81179830>] do_raw_read_lock+0x19/0x29
[<8137f063>] _raw_read_lock+0xd/0xf
[<f9081957>] tpt_trig_timer+0xc3/0x145 [mac80211]
[<f9081f3a>] ieee80211_mod_tpt_led_trig+0x152/0x174 [mac80211]
[<f9076a3f>] ieee80211_do_open+0x11e/0x42e [mac80211]
[<f9075390>] ? ieee80211_check_concurrent_iface+0x26/0x13c [mac80211]
[<f9076d97>] ieee80211_open+0x48/0x4c [mac80211]
[<812dbed8>] __dev_open+0x82/0xab
[<812dc0c9>] __dev_change_flags+0x9c/0x113
[<812dc1ae>] dev_change_flags+0x18/0x44
[<8132144f>] devinet_ioctl+0x243/0x51a
[<81321ba9>] inet_ioctl+0x93/0xac
[<812cc951>] sock_ioctl+0x1c6/0x1ea
[<812cc78b>] ? might_fault+0x20/0x20
[<810b1ebb>] do_vfs_ioctl+0x46e/0x4a2
[<810a6ebb>] ? fget_light+0x2f/0x70
[<812ce549>] ? sys_recvmsg+0x3e/0x48
[<810b1f35>] sys_ioctl+0x46/0x69
[<8137fa77>] sysenter_do_call+0x12/0x2
Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Abhijit Pradhan <abhijit@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Treat pwmX as a measured value, not as a (mostly static) limit value, so
that it is updated more frequently from the device register.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Just like skb->cb[], so that qdisc_skb_cb can be encapsulated inside
of other data structures.
This is intended to be used by IPoIB so that it can remember
addressing information stored at hard_header_ops->create() time that
it can fetch when the packet gets to the transmit routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive FIFO wakeup latency estimate in the omap-serial driver is
three orders of magnitude too small. This effectively prevents the
MPU from going to a low-power state when CONFIG_CPU_IDLE=y. This is a
major power management regression and masks some other FIFO-related
bugs in the driver.
Fix by correcting the most egregious problem in the RX wakeup latency
estimate. There are several other flaws in the estimator; these will
be fixed by a separate patch series intended for 3.4.
The difference in low-power states with this patch can be observed via
debugfs in pm_debug/count.
This estimate does not have any effect when CONFIG_CPU_IDLE=n.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode. This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached. This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode. The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.
This fix changes the erratum i291 DMA idle workaround. Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle. The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.
This fix should work on all OMAP UARTs. Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.
Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the (default) PIO mode, use a one-byte RX FIFO threshold. The OMAP
UART IP blocks do not appear to be capable of waking the system under
an RX timeout condition. Since the previous RX FIFO threshold was 16
bytes, this meant that omap-serial.c did not become aware of any
received data until all those bytes arrived or until another UART
interrupt occurred. This made the serial console and presumably other
serial applications (GPS, serial Bluetooth) unusable or extremely
slow. A 1-byte RX FIFO threshold also allows the MPU to enter a
low-power consumption state while waiting for the FIFO to fill.
This can be verified using the serial console by comparing the
behavior when "0123456789abcde" is pasted in from another window, with
the behavior when "0123456789abcdef" is pasted in. Since the former
string is less than sixteen bytes long, the string is not echoed for
some time, while the latter string is echoed immediately.
DMA operation is unaffected by this patch.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for some
additional information on the standard behavior of the RX timeout
event, which was used to improve this commit description.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Govindraj Raja <govindraj.r@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_parse_integer() does one or two division instructions (which are slow)
per digit parsed to perform the overflow check.
Furthermore, these are particularly expensive examples of division
instruction as the number of clock cycles required to complete them may
go up with the position of the most significant set bit in the dividend:
if (*res > div_u64(ULLONG_MAX - val, base))
which is as maximal as possible.
Worse, on 32-bit arches, more than one of these division instructions
may be required per digit.
So, assuming we don't support a base of more than 16, skip the check if the
top nibble of the result is not set at this point.
Signed-off-by: David Howells <dhowells@redhat.com>
[ Changed it to not dereference the pointer all the time - even if the
compiler can and does optimize it away, the code just looks cleaner.
And edited the top nybble test slightly to make the code generated on
x86-64 better in the loop - test against a hoisted constant instead of
shifting and testing the result ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H Hartley Sweeten
Lee Jones
Neal Cardwell
Arnd Bergmann
Roy Zang
Linus Torvalds
Tejun Heo
Yinghai Lu
Thomas Graf
Li Wei
Neil Horman
Vaidyanathan Srinivasan
Yinghai Lu
Christoph Hellwig
Axel Lin
Dave Airlie
Dan Carpenter
Paul Walmsley
Andrew Lunn
David Miller
Simon Graham
Mohammed Shafi Shajakhan
Nikolaus Schulz
David Howells