The driver always ends a read with a STOP condition which
breaks subsequent I2C reads/writes in the same transaction as
these expect to do a repeated START(ReSTART).
This will also help I2C multimaster as the bus will not be released
after the first read, but when the whole transaction ends.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The controller can't do anything else before it actually generates START/STOP.
So we check busy bit to make sure START/STOP is successfully finished.
If we don't check busy bit, START/STOP may fail on some fast CPUs.
Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When an ACPI resource conflict is detected, error messages are already
printed by ACPI. There's no point in causing the driver core to print
more error messages, so return one of the error codes for which no
message is printed.
This fixes bug #14293:
http://bugzilla.kernel.org/show_bug.cgi?id=14293
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We recently removed the acpi_device_uid() interface because nobody
used it. I don't think it's essential here either.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Clearly mark ACPI drivers as such
i2c: Add driver for SMBus Control Method Interface
i2c-pnx: Correct use of request_region/request_mem_region
MAINTAINERS: Add maintainer for AT24 and PCA9564/PCA9665
i2c-piix4: Add AMD SB900 SMBus device ID
i2c/chips: Remove deprecated pcf8574 driver
i2c/chips: Remove deprecated pca9539 driver
i2c/chips: Remove deprecated pcf8575 driver
gpio/pcf857x: Copy i2c_device_id from old pcf8574 driver
i2c/scx200_acb: Provide more information on bus errors
i2c: Provide compatibility links for i2c adapters
i2c: Convert i2c adapters to bus devices
i2c: Convert i2c clients to a device type
i2c/tsl2550: Use combined SMBus transactions
i2c-taos-evm: Switch echo off to improve performance
i2c: Drop unused i2c_driver.id field
As I2C is used by PMICs also, make the busses available early via
subsys_initcall().
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The mv64xxx_i2c_intr() irq handler in drivers/i2c/busses/i2c-mv64xxx.c
is declared as returning 'int', resulting in this compile-time warning:
drivers/i2c/busses/i2c-mv64xxx.c: In function 'mv64xxx_i2c_probe':
drivers/i2c/busses/i2c-mv64xxx.c:540: warning: passing argument 2 of 'request_irq' from incompatible pointer type
Fix: correct the return type to 'irqreturn_t'.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Now that we have ACPI-based SMBus controller drivers, and we will start
telling users to use them instead of native drivers when I/O resources
conflict, I think it would be good to clearly mark ACPI drivers as such
in Kconfig.
This is exactly the same as we just did for hwmon drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Crane Cai <crane.cai@amd.com>
This driver supports the SMBus Control Method Interface. It needs BIOS declare
ACPI control methods which described in SMBus Control Method Interface Spec.
http://smbus.org/specs/smbus_cmi10.pdf
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
request_mem_region should be used when ioremap is used subsequently.
release_region is then correspondingly replaced by release_mem_region.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression start,E;
@@
- request_region
+ request_mem_region
(start,...)
... when != request_mem_region(start,...)
when != start = E
ioremap(start,...)
@@
expression r.start;
@@
- release_region
+ release_mem_region
(start,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The pcf8574 driver in drivers/i2c/chips which just exports its register to
sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The pca9539 driver in drivers/i2c/chips which just exports its registers to
sysfs is superseded by drivers/gpio/pca953x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The pcf8575 driver in drivers/i2c/chips which just exports its register to
sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upon a bus error, it's rather hard to guess what happened. Dumping the
address, length and status provides a lot of value for troubleshooting
issues.
Signed-off-by: Willy Tarreau <wtarreau@exceliance.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some user-space applications may be relying on i2c adapters showing up
as class devices in sysfs. Provide compatibility links for them for
the time being. We will remove them after a long transition period.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Kay says i2c adapters shouldn't be class devices but bus devices.
Convert them that way, using a device type.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Make the I/O faster, mainly by using combined SMBus transactions when
possible. While the TSL2550 datasheet doesn't say the device supports
them, they seem to work just fine in practice, and a combined
transaction is faster than two simple transactions in many cases and
always more reliable.
A side effect is to suppress the delays between SMBus writes and
reads. The datasheet doesn't say they are needed and things work just
fine for me without them.
I also couldn't see any reason for the delay between reading the two
channels. Nor for the loop to get a reading in the first place. The
400 ms delay between samples only matters at chip power-up, after that
the chip always hold the previously sampled value so we never get to
wait.
All these changes make reading the lux value much faster and cheaper.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michele De Candia <michele.decandia@valueteam.com>
Cc: Rodolfo Giometti <giometti@linux.it>
When echo is on, we waste time reading back our orders. Switching echo
off makes performance much better: SMBus byte data transactions are 47%
faster and byte transactions are 24% faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
PXA I2C module is also used in Marvell PXA168 and PXA910 series.
Update the module dependancy of PXA I2C.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch modifies the SuperH Mobile I2C driver to support
Runtime PM. These changes is all that is needed for proper
Runtime PM support in this driver. Driver callbacks for
Runtime PM are empty because the device registers are always
re-initialized after pm_runtime_get_sync().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- blk clk is enabled when an irq arrives. The clk should be enabled,
but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
downwards.
- Number of address send attempts before giving up is increased to 12
from 10 since it most times take 8 tries before getting through.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.
The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When an XRDY/XDR is hit, wait for XUDF before writing data to DATA_REG.
Otherwise some data bytes can be lost while transferring them from the
memory to the I2C interface.
Do a Busy-wait for XUDF, before writing data to DATA_REG. While waiting
if there is NACK | AL, set the appropriate error flags, ack the pending
interrupts and return from the ISR.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In case of a NACK or ARDY or AL interrupt, complete the request.
There is no need to service the RRDY/RDR or XRDY/XDR interrupts.
Refer TRM SWPU114: Figure 18-31.I2C Master Transmitter Mode, Interrupt Method,
in F/S and HS Modes
http://focus.ti.com/pdfs/wtbu/SWPU114T_PrelimFinalEPDF_06_25_2009.pdf
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix bug in reading the I2C_BUFFSTAT register for getting byte count on RX/TX interrupt.
On Interrupt: I2C_STAT[RDR],
read 'RXSTAT' from I2C_BUFFSTAT[8-13]
On Interrupt: I2C_STAT[XDR]
read 'TXSTAT' from I2C_BUFFSTAT[0-5]
Signed-off-by: Jagadeesh Pakaravoor <j-pakaravoor@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Convert the i2c-sh_mobile i2c bus driver to use
subsys_initcall() instead of module_init().
This change makes the driver register a bit earlier which
together with earlier platform data moves the time for probe().
The earlier probe() makes it possible to use i2c_get_adapter()
and i2c_transfer() from device_initcall().
The same strategy is used by other i2c bus drivers such as
i2c-pxa.c and i2c-s3c2410.c.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
[ben-linux@fluff.org: minor subject updaye]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
s3c24xx_i2c_init() was overwriting the IICLC value set just above in
s3c24xx_i2c_clockrate() with zero, effectively disabling the platform
line control setting.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
I've tested TSL2550 driver and I've found a bug: when light is off,
returned value from tsl2550_calculate_lux function is -1 when it should
be 0 (sensor correctly read that light was off).
I think the bug is that a zero c0 value (approximated value of ch0) is
misinterpreted as an error.
Signed-off-by: Michele Jr De Candia <michele.decandia@valueteam.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is V2 of the i2c-s3c2410 dev_pm_ops patch.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend_late() -> suspend_noirq()
resume() -> resume()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch reworks platform driver power management code
for i2c-pxa from legacy late/early callbacks to dev_pm_ops.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend_late() -> suspend_noirq()
resume_early() -> resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make i2c-davinci cope properly with "i2cdetect": don't spew
syslog spam on perfectly normal behaviors, or respond to any
address other than the one reserved for the SMBus host.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
DaVinci core code has converted to the new clkdev API so
clock name strings are not needed. Instead, just the a
'struct device' pointer is needed.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This build error triggers on x86:
drivers/built-in.o: In function `i2c_dw_init':
i2c-designware.c:(.text+0x4e37ca): undefined reference to `clk_get_rate'
drivers/built-in.o: In function `dw_i2c_probe':
i2c-designware.c:(.devinit.text+0x51f5e): undefined reference to `clk_get'
i2c-designware.c:(.devinit.text+0x51f76): undefined reference to `clk_enable'
i2c-designware.c:(.devinit.text+0x520ff): undefined reference to `clk_disable'
i2c-designware.c:(.devinit.text+0x52108): undefined reference to `clk_put'
Because this new driver uses the clk_*() facilities which is an
ARM-only thing currently.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i2c Linux driver for the DesignWare i2c block of Synopsys, which is meant
for AMBA Peripheral Bus. This i2c block is used on SoC chips like the ARM9
based PVG610.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When a process tries to read/write a disconnected i2c device, it receives a signal (e.g. ctrl-c) and the kernel gets stuck.
BUG: soft lockup - CPU#0 stuck for 61s! [I2CEEpromTest:392]
NIP: c01628f8 LR: c01628f0 CTR: c00177cc
REGS: c39abd70 TRAP: 0901 Not tainted (2.6.25.7-alcore)
MSR: 00009032 <EE,ME,IR,DR> CR: 42042048 XER: 20000000
TASK = c3889bd0[392] 'I2CEEpromTest' THREAD: c39aa000
GPR00: 00009000 c39abe20 c3889bd0 c39075c8 c39abe28 00000001 00000000 00000001
GPR08: c3889bd0 c39075c8 00009032 c39abe34 00002437
NIP [c01628f8] cpm_i2c_xfer+0x5fc/0x6d0
LR [c01628f0] cpm_i2c_xfer+0x5f4/0x6d0
Call Trace:
[c39abe20] [c0162924] cpm_i2c_xfer+0x628/0x6d0 (unreliable)
[c39abe90] [c015f6a0] i2c_transfer+0x88/0xb4
[c39abeb0] [c0160164] i2c_master_recv+0x48/0x6c
[c39abed0] [c01618dc] i2cdev_read+0x50/0xe4
[c39abef0] [c0068b24] vfs_read+0xc4/0x108
[c39abf10] [c0068f4c] sys_read+0x4c/0x90
[c39abf40] [c000d348] ret_from_syscall+0x0/0x38
Instruction dump:
3bc00064 92610010 3bf201c8 92810014 3b61
This happen because though the wait_event_interruptible_timeout takes the
signals into account, the driver does not handle them.
We propose to change the wait_event_interruptible_timeout with
wait_event_timeout, leaving the signals to be handled in other points
on the upper layers.
Signed-off-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
[ben-linux@fluff.org: fix title for patch]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Hi Ben,
Can you please queue this fix?
Thanks,
Tony
>From ffe2b2cdf6283770b70a197e3748c6b40a1006be Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Wed, 17 Jun 2009 13:14:23 +0300
Subject: [PATCH] i2c-omap: Fix build breaking typo in cpu_is_omap_2430
Commit 84bf2c86 introduced a typo, it should be cpu_is_omap2430
instead. The typo was probably caused by a mismerge.
Without this patch all omaps fail to build with:
error: implicit declaration of function 'cpu_is_omap_2430'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Joakim Tjernlund
Richard Zhao
Jean Delvare
Bjorn Helgaas
Russell King
Linus Torvalds
Wolfram Sang
Mikael Pettersson
Crane Cai
Julia Lawall
Willy Tarreau
Haojian Zhuang
Magnus Damm
Rafael J. Wysocki
Linus Walleij
Moiz Sonasath
Nishanth Menon
Roel Kluin
Peter Korsgaard
Michele Jr De Candia
David Brownell
Kevin Hilman
Joe Perches
Ingo Molnar
Baruch Siach
Michael Trimarchi
Tony Lindgren