In this patch, we add dcbnl buffer attribute to allow user
change the NIC's buffer configuration such as priority
to buffer mapping and buffer size of individual buffer.
This attribute combined with pfc attribute allows advanced user to
fine tune the qos setting for specific priority queue. For example,
user can give dedicated buffer for one or more priorities or user
can give large buffer to certain priorities.
The dcb buffer configuration will be controlled by lldptool.
lldptool -T -i eth2 -V BUFFER prio 0,2,5,7,1,2,3,6
maps priorities 0,1,2,3,4,5,6,7 to receive buffer 0,2,5,7,1,2,3,6
lldptool -T -i eth2 -V BUFFER size 87296,87296,0,87296,0,0,0,0
sets receive buffer size for buffer 0,1,2,3,4,5,6,7 respectively
After discussion on mailing list with Jakub, Jiri, Ido and John, we agreed to
choose dcbnl over devlink interface since this feature is intended to set
port attributes which are governed by the netdev instance of that port, where
devlink API is more suitable for global ASIC configurations.
We present an use case scenario where dcbnl buffer attribute configured
by advance user helps reduce the latency of messages of different sizes.
Scenarios description:
On ConnectX-5, we run latency sensitive traffic with
small/medium message sizes ranging from 64B to 256KB and bandwidth sensitive
traffic with large messages sizes 512KB and 1MB. We group small, medium,
and large message sizes to their own pfc enables priorities as follow.
Priorities 1 & 2 (64B, 256B and 1KB)
Priorities 3 & 4 (4KB, 8KB, 16KB, 64KB, 128KB and 256KB)
Priorities 5 & 6 (512KB and 1MB)
By default, ConnectX-5 maps all pfc enabled priorities to a single
lossless fixed buffer size of 50% of total available buffer space. The
other 50% is assigned to lossy buffer. Using dcbnl buffer attribute,
we create three equal size lossless buffers. Each buffer has 25% of total
available buffer space. Thus, the lossy buffer size reduces to 25%. Priority
to lossless buffer mappings are set as follow.
Priorities 1 & 2 on lossless buffer #1
Priorities 3 & 4 on lossless buffer #2
Priorities 5 & 6 on lossless buffer #3
We observe improvements in latency for small and medium message sizes
as follows. Please note that the large message sizes bandwidth performance is
reduced but the total bandwidth remains the same.
256B message size (42 % latency reduction)
4K message size (21% latency reduction)
64K message size (16% latency reduction)
CC: Ido Schimmel <idosch@idosch.org>
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Or Gerlitz <gerlitz.or@gmail.com>
CC: Parav Pandit <parav@mellanox.com>
CC: Aron Silverton <aron.silverton@oracle.com>
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
- Remove bouncing addresses from the MAINTAINERS file
- Kernel oops and bad error handling fixes for hfi, i40iw, cxgb4, and hns drivers
- Various small LOC behavioral/operational bugs in mlx5, hns, qedr and i40iw drivers
- Two fixes for patches already sent during the merge window
- A long standing bug related to not decreasing the pinned pages count in the right
MM was found and fixed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uFZh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"This is pretty much just the usual array of smallish driver bugs.
- remove bouncing addresses from the MAINTAINERS file
- kernel oops and bad error handling fixes for hfi, i40iw, cxgb4, and
hns drivers
- various small LOC behavioral/operational bugs in mlx5, hns, qedr
and i40iw drivers
- two fixes for patches already sent during the merge window
- a long-standing bug related to not decreasing the pinned pages
count in the right MM was found and fixed"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (28 commits)
RDMA/hns: Move the location for initializing tmp_len
RDMA/hns: Bugfix for cq record db for kernel
IB/uverbs: Fix uverbs_attr_get_obj
RDMA/qedr: Fix doorbell bar mapping for dpi > 1
IB/umem: Use the correct mm during ib_umem_release
iw_cxgb4: Fix an error handling path in 'c4iw_get_dma_mr()'
RDMA/i40iw: Avoid panic when reading back the IRQ affinity hint
RDMA/i40iw: Avoid reference leaks when processing the AEQ
RDMA/i40iw: Avoid panic when objects are being created and destroyed
RDMA/hns: Fix the bug with NULL pointer
RDMA/hns: Set NULL for __internal_mr
RDMA/hns: Enable inner_pa_vld filed of mpt
RDMA/hns: Set desc_dma_addr for zero when free cmq desc
RDMA/hns: Fix the bug with rq sge
RDMA/hns: Not support qp transition from reset to reset for hip06
RDMA/hns: Add return operation when configured global param fail
RDMA/hns: Update convert function of endian format
RDMA/hns: Load the RoCE dirver automatically
RDMA/hns: Bugfix for rq record db for kernel
RDMA/hns: Add rq inline flags judgement
...
In struct phy_device we have a number of flags being defined as type
bool. Similar to e.g. struct pci_dev we can save some space by using
bit-fields.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=iYyx
-----END PGP SIGNATURE-----
Merge tag 'for-4.17-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"A one-liner that prevents leaking an internal error value 1 out of the
ftruncate syscall.
This has been observed in practice. The steps to reproduce make a
common pattern (open/write/fync/ftruncate) but also need the
application to not check only for negative values and happens only for
compressed inlined files.
The conditions are narrow but as this could break userspace I think
it's better to merge it now and not wait for the merge window"
* tag 'for-4.17-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix error handling in btrfs_truncate()
Before commit 3b5b899ca6 ("ALSA: hda: Make use of core codec functions
to sync power state"), hda_set_power_state() returned the response to
the Get Power State verb, a 32-bit unsigned integer whose expected value
is 0x233 after transitioning a codec to D3, and 0x0 after transitioning
it to D0.
The response value is significant because hda_codec_runtime_suspend()
does not clear the codec's bit in the codec_powered bitmask unless the
AC_PWRST_CLK_STOP_OK bit (0x200) is set in the response value. That in
turn prevents the HDA controller from runtime suspending because
azx_runtime_idle() checks that the codec_powered bitmask is zero.
Since commit 3b5b899ca6, hda_set_power_state() only returns 0x0 or
0x1, thereby breaking runtime PM for any HDA controller. That's because
an inline function introduced by the commit returns a bool instead of a
32-bit unsigned int. The change was likely erroneous and resulted from
copying and pasting snd_hda_check_power_state(), which is immediately
preceding the newly introduced inline function. Fix it.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=106597
Fixes: 3b5b899ca6 ("ALSA: hda: Make use of core codec functions to sync power state")
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Abhijeet Kumar <abhijeet.kumar@intel.com>
Reported-and-tested-by: Gunnar Krüger <taijian@posteo.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts the following commits that change CMA design in MM.
3d2054ad8c ("ARM: CMA: avoid double mapping to the CMA area if CONFIG_HIGHMEM=y")
1d47a3ec09 ("mm/cma: remove ALLOC_CMA")
bad8c6c0b1 ("mm/cma: manage the memory of the CMA area by using the ZONE_MOVABLE")
Ville reported a following error on i386.
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
microcode: microcode updated early to revision 0x4, date = 2013-06-28
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:00118000)
Initializing Movable for node 0 (00000001:00118000)
BUG: Bad page state in process swapper pfn:377fe
page:f53effc0 count:0 mapcount:-127 mapping:00000000 index:0x0
flags: 0x80000000()
raw: 80000000 00000000 00000000 ffffff80 00000000 00000100 00000200 00000001
page dumped because: nonzero mapcount
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 4.17.0-rc5-elk+ #145
Hardware name: Dell Inc. Latitude E5410/03VXMC, BIOS A15 07/11/2013
Call Trace:
dump_stack+0x60/0x96
bad_page+0x9a/0x100
free_pages_check_bad+0x3f/0x60
free_pcppages_bulk+0x29d/0x5b0
free_unref_page_commit+0x84/0xb0
free_unref_page+0x3e/0x70
__free_pages+0x1d/0x20
free_highmem_page+0x19/0x40
add_highpages_with_active_regions+0xab/0xeb
set_highmem_pages_init+0x66/0x73
mem_init+0x1b/0x1d7
start_kernel+0x17a/0x363
i386_start_kernel+0x95/0x99
startup_32_smp+0x164/0x168
The reason for this error is that the span of MOVABLE_ZONE is extended
to whole node span for future CMA initialization, and, normal memory is
wrongly freed here. I submitted the fix and it seems to work, but,
another problem happened.
It's so late time to fix the later problem so I decide to reverting the
series.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull libata fixes from Tejun Heo:
"Nothing too interesting. Four patches to update the blacklist and
add a controller ID"
* 'for-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Add PCI ID for Cannon Lake PCH-LP AHCI
libata: blacklist Micron 500IT SSD with MU01 firmware
libata: Apply NOLPM quirk for SAMSUNG PM830 CXM13D1Q.
libata: Blacklist some Sandisk SSDs for NCQ
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QBaF
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180524' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Two fixes that should go into this release:
- a loop writeback error clearing fix from Jeff
- the sr sense fix from myself"
* tag 'for-linus-20180524' of git://git.kernel.dk/linux-block:
loop: clear wb_err in bd_inode when detaching backing file
sr: pass down correctly sized SCSI sense buffer
Fix a regression from the 4.15 cycle that caused the system suspend
and resume overhead to increase on many systems and triggered more
serious problems on some of them (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BS+S
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a regression from the 4.15 cycle that caused the system suspend
and resume overhead to increase on many systems and triggered more
serious problems on some of them (Rafael Wysocki)"
* tag 'pm-4.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / core: Fix direct_complete handling for devices with no callbacks
While reviewing the verifier code, I recently noticed that the
following two program variants in relation to tail calls can be
loaded.
Variant 1:
# bpftool p d x i 15
0: (15) if r1 == 0x0 goto pc+3
1: (18) r2 = map[id:5]
3: (05) goto pc+2
4: (18) r2 = map[id:6]
6: (b7) r3 = 7
7: (35) if r3 >= 0xa0 goto pc+2
8: (54) (u32) r3 &= (u32) 255
9: (85) call bpf_tail_call#12
10: (b7) r0 = 1
11: (95) exit
# bpftool m s i 5
5: prog_array flags 0x0
key 4B value 4B max_entries 4 memlock 4096B
# bpftool m s i 6
6: prog_array flags 0x0
key 4B value 4B max_entries 160 memlock 4096B
Variant 2:
# bpftool p d x i 20
0: (15) if r1 == 0x0 goto pc+3
1: (18) r2 = map[id:8]
3: (05) goto pc+2
4: (18) r2 = map[id:7]
6: (b7) r3 = 7
7: (35) if r3 >= 0x4 goto pc+2
8: (54) (u32) r3 &= (u32) 3
9: (85) call bpf_tail_call#12
10: (b7) r0 = 1
11: (95) exit
# bpftool m s i 8
8: prog_array flags 0x0
key 4B value 4B max_entries 160 memlock 4096B
# bpftool m s i 7
7: prog_array flags 0x0
key 4B value 4B max_entries 4 memlock 4096B
In both cases the index masking inserted by the verifier in order
to control out of bounds speculation from a CPU via b2157399cc
("bpf: prevent out-of-bounds speculation") seems to be incorrect
in what it is enforcing. In the 1st variant, the mask is applied
from the map with the significantly larger number of entries where
we would allow to a certain degree out of bounds speculation for
the smaller map, and in the 2nd variant where the mask is applied
from the map with the smaller number of entries, we get buggy
behavior since we truncate the index of the larger map.
The original intent from commit b2157399cc is to reject such
occasions where two or more different tail call maps are used
in the same tail call helper invocation. However, the check on
the BPF_MAP_PTR_POISON is never hit since we never poisoned the
saved pointer in the first place! We do this explicitly for map
lookups but in case of tail calls we basically used the tail
call map in insn_aux_data that was processed in the most recent
path which the verifier walked. Thus any prior path that stored
a pointer in insn_aux_data at the helper location was always
overridden.
Fix it by moving the map pointer poison logic into a small helper
that covers both BPF helpers with the same logic. After that in
fixup_bpf_calls() the poison check is then hit for tail calls
and the program rejected. Latter only happens in unprivileged
case since this is the *only* occasion where a rewrite needs to
happen, and where such rewrite is specific to the map (max_entries,
index_mask). In the privileged case the rewrite is generic for
the insn->imm / insn->code update so multiple maps from different
paths can be handled just fine since all the remaining logic
happens in the instruction processing itself. This is similar
to the case of map lookups: in case there is a collision of
maps in fixup_bpf_calls() we must skip the inlined rewrite since
this will turn the generic instruction sequence into a non-
generic one. Thus the patch_call_imm will simply update the
insn->imm location where the bpf_map_lookup_elem() will later
take care of the dispatch. Given we need this 'poison' state
as a check, the information of whether a map is an unpriv_array
gets lost, so enforcing it prior to that needs an additional
state. In general this check is needed since there are some
complex and tail call intensive BPF programs out there where
LLVM tends to generate such code occasionally. We therefore
convert the map_ptr rather into map_state to store all this
w/o extra memory overhead, and the bit whether one of the maps
involved in the collision was from an unpriv_array thus needs
to be retained as well there.
Fixes: b2157399cc ("bpf: prevent out-of-bounds speculation")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
- bump version strings, by Simon Wunderlich
- Disable batman-adv debugfs by default, by Sven Eckelmann
- Improve handling mesh nodes with multicast optimizations disabled,
by Linus Luessing
- Avoid bool in structs, by Sven Eckelmann
- Allocate less memory when debugfs is disabled, by Sven Eckelmann
- Fix batadv_interface_tx return data type, by Luc Van Oostenryck
- improve link speed handling for virtual interfaces, by Marek Lindner
- Enable BATMAN V algorithm by default, by Marek Lindner
-----BEGIN PGP SIGNATURE-----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=Cc4J
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20180524' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Disable batman-adv debugfs by default, by Sven Eckelmann
- Improve handling mesh nodes with multicast optimizations disabled,
by Linus Luessing
- Avoid bool in structs, by Sven Eckelmann
- Allocate less memory when debugfs is disabled, by Sven Eckelmann
- Fix batadv_interface_tx return data type, by Luc Van Oostenryck
- improve link speed handling for virtual interfaces, by Marek Lindner
- Enable BATMAN V algorithm by default, by Marek Lindner
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This one should be using the default LPM policy for mobile chipsets so
add the PCI ID to the driver list of supported revices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Passing O_CREAT (00000100) to open means we should also pass file
mode as the third parameter. Creating /dev/console as a regular
file may not be helpful anyway, so simply drop the flag when
opening debug_fd.
Fixes: d2ba09c17a ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPFILTER could have been enabled without INET causing this build error:
ERROR: "bpfilter_process_sockopt" [net/bpfilter/bpfilter.ko] undefined!
Fixes: d2ba09c17a ("net: add skeleton of bpfilter kernel module")
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 15122ee2c5 ("arm64: Enforce BBM for huge IO/VMAP mappings")
disallowed block mappings for ioremap since that code does not honor
break-before-make. The same APIs are also used for permission updating
though and the extra checks prevent the permission updates from happening,
even though this should be permitted. This results in read-only permissions
not being fully applied. Visibly, this can occasionaly be seen as a failure
on the built in rodata test when the test data ends up in a section or
as an odd RW gap on the page table dump. Fix this by using
pgattr_change_is_safe instead of p*d_present for determining if the
change is permitted.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Fixes: 15122ee2c5 ("arm64: Enforce BBM for huge IO/VMAP mappings")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mathieu Xhonneux says:
====================
As of Linux 4.14, it is possible to define advanced local processing for
IPv6 packets with a Segment Routing Header through the seg6local LWT
infrastructure. This LWT implements the network programming principles
defined in the IETF "SRv6 Network Programming" draft.
The implemented operations are generic, and it would be very interesting to
be able to implement user-specific seg6local actions, without having to
modify the kernel directly. To do so, this patchset adds an End.BPF action
to seg6local, powered by some specific Segment Routing-related helpers,
which provide SR functionalities that can be applied on the packet. This
BPF hook would then allow to implement specific actions at native kernel
speed such as OAM features, advanced SR SDN policies, SRv6 actions like
Segment Routing Header (SRH) encapsulation depending on the content of
the packet, etc.
This patchset is divided in 6 patches, whose main features are :
- A new seg6local action End.BPF with the corresponding new BPF program
type BPF_PROG_TYPE_LWT_SEG6LOCAL. Such attached BPF program can be
passed to the LWT seg6local through netlink, the same way as the LWT
BPF hook operates.
- 3 new BPF helpers for the seg6local BPF hook, allowing to edit/grow/
shrink a SRH and apply on a packet some of the generic SRv6 actions.
- 1 new BPF helper for the LWT BPF IN hook, allowing to add a SRH through
encapsulation (via IPv6 encapsulation or inlining if the packet contains
already an IPv6 header).
As this patchset adds a new LWT BPF hook, I took into account the result
of the discussions when the LWT BPF infrastructure got merged. Hence, the
seg6local BPF hook doesn't allow write access to skb->data directly, only
the SRH can be modified through specific helpers, which ensures that the
integrity of the packet is maintained. More details are available in the
related patches messages.
The performances of this BPF hook have been assessed with the BPF JIT
enabled on an Intel Xeon X3440 processors with 4 cores and 8 threads
clocked at 2.53 GHz. No throughput losses are noted with the seg6local
BPF hook when the BPF program does nothing (440kpps). Adding a 8-bytes
TLV (1 call each to bpf_lwt_seg6_adjust_srh and bpf_lwt_seg6_store_bytes)
drops the throughput to 410kpps, and inlining a SRH via bpf_lwt_seg6_action
drops the throughput to 420kpps. All throughputs are stable.
Changelog:
v2: move the SRH integrity state from skb->cb to a per-cpu buffer
v3: - document helpers in man-page style
- fix kbuild bugs
- un-break BPF LWT out hook
- bpf_push_seg6_encap is now static
- preempt_enable is now called when the packet is dropped in
input_action_end_bpf
v4: fix kbuild bugs when CONFIG_IPV6=m
v5: fix kbuild sparse warnings when CONFIG_IPV6=m
v6: fix skb pointers-related bugs in helpers
v7: - fix memory leak in error path of End.BPF setup
- add freeing of BPF data in seg6_local_destroy_state
- new enums SEG6_LOCAL_BPF_* instead of re-using ones of lwt bpf for
netlink nested bpf attributes
- SEG6_LOCAL_BPF_PROG attr now contains prog->aux->id when dumping
state
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add a new test for the seg6local End.BPF action. The following helpers
are also tested:
- bpf_lwt_push_encap within the LWT BPF IN hook
- bpf_lwt_seg6_action
- bpf_lwt_seg6_adjust_srh
- bpf_lwt_seg6_store_bytes
A chain of End.BPF actions is built. The SRH is injected through a LWT
BPF IN hook before entering this chain. Each End.BPF action validates
the previous one, otherwise the packet is dropped. The test succeeds
if the last node in the chain receives the packet and the UDP datagram
contained can be retrieved from userspace.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch adds the End.BPF action to the LWT seg6local infrastructure.
This action works like any other seg6local End action, meaning that an IPv6
header with SRH is needed, whose DA has to be equal to the SID of the
action. It will also advance the SRH to the next segment, the BPF program
does not have to take care of this.
Since the BPF program may not be a source of instability in the kernel, it
is important to ensure that the integrity of the packet is maintained
before yielding it back to the IPv6 layer. The hook hence keeps track if
the SRH has been altered through the helpers, and re-validates its
content if needed with seg6_validate_srh. The state kept for validation is
stored in a per-CPU buffer. The BPF program is not allowed to directly
write into the packet, and only some fields of the SRH can be altered
through the helper bpf_lwt_seg6_store_bytes.
Performances profiling has shown that the SRH re-validation does not induce
a significant overhead. If the altered SRH is deemed as invalid, the packet
is dropped.
This validation is also done before executing any action through
bpf_lwt_seg6_action, and will not be performed again if the SRH is not
modified after calling the action.
The BPF program may return 3 types of return codes:
- BPF_OK: the End.BPF action will look up the next destination through
seg6_lookup_nexthop.
- BPF_REDIRECT: if an action has been executed through the
bpf_lwt_seg6_action helper, the BPF program should return this
value, as the skb's destination is already set and the default
lookup should not be performed.
- BPF_DROP : the packet will be dropped.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The new bpf_lwt_push_encap helper should only be accessible within the
LWT BPF IN hook, and not the OUT one, as this may lead to a skb under
panic.
At the moment, both LWT BPF IN and OUT share the same list of helpers,
whose calls are authorized by the verifier. This patch separates the
verifier ops for the IN and OUT hooks, and allows the IN hook to call the
bpf_lwt_push_encap helper.
This patch is also the occasion to put all lwt_*_func_proto functions
together for clarity. At the moment, socks_op_func_proto is in the middle
of lwt_inout_func_proto and lwt_xmit_func_proto.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The BPF seg6local hook should be powerful enough to enable users to
implement most of the use-cases one could think of. After some thinking,
we figured out that the following actions should be possible on a SRv6
packet, requiring 3 specific helpers :
- bpf_lwt_seg6_store_bytes: Modify non-sensitive fields of the SRH
- bpf_lwt_seg6_adjust_srh: Allow to grow or shrink a SRH
(to add/delete TLVs)
- bpf_lwt_seg6_action: Apply some SRv6 network programming actions
(specifically End.X, End.T, End.B6 and
End.B6.Encap)
The specifications of these helpers are provided in the patch (see
include/uapi/linux/bpf.h).
The non-sensitive fields of the SRH are the following : flags, tag and
TLVs. The other fields can not be modified, to maintain the SRH
integrity. Flags, tag and TLVs can easily be modified as their validity
can be checked afterwards via seg6_validate_srh. It is not allowed to
modify the segments directly. If one wants to add segments on the path,
he should stack a new SRH using the End.B6 action via
bpf_lwt_seg6_action.
Growing, shrinking or editing TLVs via the helpers will flag the SRH as
invalid, and it will have to be re-validated before re-entering the IPv6
layer. This flag is stored in a per-CPU buffer, along with the current
header length in bytes.
Storing the SRH len in bytes in the control block is mandatory when using
bpf_lwt_seg6_adjust_srh. The Header Ext. Length field contains the SRH
len rounded to 8 bytes (a padding TLV can be inserted to ensure the 8-bytes
boundary). When adding/deleting TLVs within the BPF program, the SRH may
temporary be in an invalid state where its length cannot be rounded to 8
bytes without remainder, hence the need to store the length in bytes
separately. The caller of the BPF program can then ensure that the SRH's
final length is valid using this value. Again, a final SRH modified by a
BPF program which doesn’t respect the 8-bytes boundary will be discarded
as it will be considered as invalid.
Finally, a fourth helper is provided, bpf_lwt_push_encap, which is
available from the LWT BPF IN hook, but not from the seg6local BPF one.
This helper allows to encapsulate a Segment Routing Header (either with
a new outer IPv6 header, or by inlining it directly in the existing IPv6
header) into a non-SRv6 packet. This helper is required if we want to
offer the possibility to dynamically encapsulate a SRH for non-SRv6 packet,
as the BPF seg6local hook only works on traffic already containing a SRH.
This is the BPF equivalent of the seg6 LWT infrastructure, which achieves
the same purpose but with a static SRH per route.
These helpers require CONFIG_IPV6=y (and not =m).
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The function lookup_nexthop is essential to implement most of the seg6local
actions. As we want to provide a BPF helper allowing to apply some of these
actions on the packet being processed, the helper should be able to call
this function, hence the need to make it public.
Moreover, if one argument is incorrect or if the next hop can not be found,
an error should be returned by the BPF helper so the BPF program can adapt
its processing of the packet (return an error, properly force the drop,
...). This patch hence makes this function return dst->error to indicate a
possible error.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
include/net/seg6.h cannot be included in a source file if CONFIG_IPV6 is
not enabled:
include/net/seg6.h: In function 'seg6_pernet':
>> include/net/seg6.h:52:14: error: 'struct net' has no member named
'ipv6'; did you mean 'ipv4'?
return net->ipv6.seg6_data;
^~~~
ipv4
This commit makes seg6_pernet return NULL if IPv6 is not compiled, hence
allowing seg6.h to be included regardless of the configuration.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jun Wu at Facebook reported that an internal service was seeing a return
value of 1 from ftruncate() on Btrfs in some cases. This is coming from
the NEED_TRUNCATE_BLOCK return value from btrfs_truncate_inode_items().
btrfs_truncate() uses two variables for error handling, ret and err.
When btrfs_truncate_inode_items() returns non-zero, we set err to the
return value. However, NEED_TRUNCATE_BLOCK is not an error. Make sure we
only set err if ret is an error (i.e., negative).
To reproduce the issue: mount a filesystem with -o compress-force=zstd
and the following program will encounter return value of 1 from
ftruncate:
int main(void) {
char buf[256] = { 0 };
int ret;
int fd;
fd = open("test", O_CREAT | O_WRONLY | O_TRUNC, 0666);
if (fd == -1) {
perror("open");
return EXIT_FAILURE;
}
if (write(fd, buf, sizeof(buf)) != sizeof(buf)) {
perror("write");
close(fd);
return EXIT_FAILURE;
}
if (fsync(fd) == -1) {
perror("fsync");
close(fd);
return EXIT_FAILURE;
}
ret = ftruncate(fd, 128);
if (ret) {
printf("ftruncate() returned %d\n", ret);
close(fd);
return EXIT_FAILURE;
}
close(fd);
return EXIT_SUCCESS;
}
Fixes: ddfae63cc8 ("btrfs: move btrfs_truncate_block out of trans handle")
CC: stable@vger.kernel.org # 4.15+
Reported-by: Jun Wu <quark@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Sandipan Das says:
====================
[1] Support for bpf-to-bpf function calls in the powerpc64 JIT compiler.
[2] Provide a way for resolving function calls because of the way JITed
images are allocated in powerpc64.
[3] Fix to get JITed instruction dumps for multi-function programs from
the bpf system call.
[4] Fix for bpftool to show delimited multi-function JITed image dumps.
v4:
- Incorporate review comments from Jakub.
- Fix JSON output for bpftool.
v3:
- Change base tree tag to bpf-next.
- Incorporate review comments from Alexei, Daniel and Jakub.
- Make sure that the JITed image does not grow or shrink after
the last pass due to the way the instruction sequence used
to load a callee's address maybe optimized.
- Make additional changes to the bpf system call and bpftool to
make multi-function JITed dumps easier to correlate.
v2:
- Incorporate review comments from Jakub.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Syncing the bpf.h uapi header with tools so that struct
bpf_prog_info has the two new fields for passing on the
JITed image lengths of each function in a multi-function
program.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This adds new two new fields to struct bpf_prog_info. For
multi-function programs, these fields can be used to pass
a list of the JITed image lengths of each function for a
given program to userspace using the bpf system call with
the BPF_OBJ_GET_INFO_BY_FD command.
This can be used by userspace applications like bpftool
to split up the contiguous JITed dump, also obtained via
the system call, into more relatable chunks corresponding
to each function.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, for multi-function programs, we cannot get the JITed
instructions using the bpf system call's BPF_OBJ_GET_INFO_BY_FD
command. Because of this, userspace tools such as bpftool fail
to identify a multi-function program as being JITed or not.
With the JIT enabled and the test program running, this can be
verified as follows:
# cat /proc/sys/net/core/bpf_jit_enable
1
Before applying this patch:
# bpftool prog list
1: kprobe name foo tag b811aab41a39ad3d gpl
loaded_at 2018-05-16T11:43:38+0530 uid 0
xlated 216B not jited memlock 65536B
...
# bpftool prog dump jited id 1
no instructions returned
After applying this patch:
# bpftool prog list
1: kprobe name foo tag b811aab41a39ad3d gpl
loaded_at 2018-05-16T12:13:01+0530 uid 0
xlated 216B jited 308B memlock 65536B
...
# bpftool prog dump jited id 1
0: nop
4: nop
8: mflr r0
c: std r0,16(r1)
10: stdu r1,-112(r1)
14: std r31,104(r1)
18: addi r31,r1,48
1c: li r3,10
...
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, we resolve the callee's address for a JITed function
call by using the imm field of the call instruction as an offset
from __bpf_call_base. If bpf_jit_kallsyms is enabled, we further
use this address to get the callee's kernel symbol's name.
For some architectures, such as powerpc64, the imm field is not
large enough to hold this offset. So, instead of assigning this
offset to the imm field, the verifier now assigns the subprog
id. Also, a list of kernel symbol addresses for all the JITed
functions is provided in the program info. We now use the imm
field as an index for this list to lookup a callee's symbol's
address and resolve its name.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Syncing the bpf.h uapi header with tools so that struct
bpf_prog_info has the two new fields for passing on the
addresses of the kernel symbols corresponding to each
function in a program.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This adds new two new fields to struct bpf_prog_info. For
multi-function programs, these fields can be used to pass
a list of kernel symbol addresses for all functions in a
given program to userspace using the bpf system call with
the BPF_OBJ_GET_INFO_BY_FD command.
When bpf_jit_kallsyms is enabled, we can get the address
of the corresponding kernel symbol for a callee function
and resolve the symbol's name. The address is determined
by adding the value of the call instruction's imm field
to __bpf_call_base. This offset gets assigned to the imm
field by the verifier.
For some architectures, such as powerpc64, the imm field
is not large enough to hold this offset.
We resolve this by:
[1] Assigning the subprog id to the imm field of a call
instruction in the verifier instead of the offset of
the callee's symbol's address from __bpf_call_base.
[2] Determining the address of a callee's corresponding
symbol by using the imm field as an index for the
list of kernel symbol addresses now available from
the program info.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This adds support for bpf-to-bpf function calls in the powerpc64
JIT compiler. The JIT compiler converts the bpf call instructions
to native branch instructions. After a round of the usual passes,
the start addresses of the JITed images for the callee functions
are known. Finally, to fixup the branch target addresses, we need
to perform an extra pass.
Because of the address range in which JITed images are allocated
on powerpc64, the offsets of the start addresses of these images
from __bpf_call_base are as large as 64 bits. So, for a function
call, we cannot use the imm field of the instruction to determine
the callee's address. Instead, we use the alternative method of
getting it from the list of function addresses in the auxiliary
data of the caller by using the off field as an index.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
For multi-function programs, loading the address of a callee
function to a register requires emitting instructions whose
count varies from one to five depending on the nature of the
address.
Since we come to know of the callee's address only before the
extra pass, the number of instructions required to load this
address may vary from what was previously generated. This can
make the JITed image grow or shrink.
To avoid this, we should generate a constant five-instruction
when loading function addresses by padding the optimized load
sequence with NOPs.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The imm field of a bpf instruction is a signed 32-bit integer.
For JITed bpf-to-bpf function calls, it holds the offset of the
start address of the callee's JITed image from __bpf_call_base.
For some architectures, such as powerpc64, this offset may be
as large as 64 bits and cannot be accomodated in the imm field
without truncation.
We resolve this by:
[1] Additionally using the auxiliary data of each function to
keep a list of start addresses of the JITed images for all
functions determined by the verifier.
[2] Retaining the subprog id inside the off field of the call
instructions and using it to index into the list mentioned
above and lookup the callee's address.
To make sure that the existing JIT compilers continue to work
without requiring changes, we keep the imm field as it is.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Sparse warning:
kernel/bpf/btf.c:1985:34: warning: Variable length array is used.
This patch directly uses ARRAY_SIZE().
Fixes: f80442a4cd ("bpf: btf: Change how section is supported in btf_header")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When posted work request, it need to compute the length of
all sges of every wr and fill it into the msg_len field of
send wqe. Thus, While posting multiple wr,
tmp_len should be reinitialized to zero.
Fixes: 8b9b8d143b ("RDMA/hns: Fix the endian problem for hns")
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When use cq record db for kernel, it needs to set the hr_cq->db_en
to 1 and configure the dma address of record cq db of qp context.
Fixes: 86188a8810 ("RDMA/hns: Support cq record doorbell for kernel space")
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The err pointer comes from uverbs_attr_get, not from the uobject member,
which does not store an ERR_PTR.
Fixes: be934cca9e ("IB/uverbs: Add device memory registration ioctl support")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Each user_context receives a separate dpi value and thus a different
address on the doorbell bar. The qedr_mmap function needs to validate
the address and map the doorbell bar accordingly.
The current implementation always checked against dpi=0 doorbell range
leading to a wrong mapping for doorbell bar. (It entered an else case
that mapped the address differently). qedr_mmap should only be used
for doorbells, so the else was actually wrong in the first place.
This only has an affect on arm architecture and not an issue on a
x86 based architecture.
This lead to doorbells not occurring on arm based systems and left
applications that use more than one dpi (or several applications
run simultaneously ) to hang.
Fixes: ac1b36e55a ("qedr: Add support for user context verbs")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, they are:
1) Remove obsolete nf_log tracing from nf_tables, from Florian Westphal.
2) Add support for map lookups to numgen, random and hash expressions,
from Laura Garcia.
3) Allow to register nat hooks for iptables and nftables at the same
time. Patchset from Florian Westpha.
4) Timeout support for rbtree sets.
5) ip6_rpfilter works needs interface for link-local addresses, from
Vincent Bernat.
6) Add nf_ct_hook and nf_nat_hook structures and use them.
7) Do not drop packets on packets raceing to insert conntrack entries
into hashes, this is particularly a problem in nfqueue setups.
8) Address fallout from xt_osf separation to nf_osf, patches
from Florian Westphal and Fernando Mancera.
9) Remove reference to struct nft_af_info, which doesn't exist anymore.
From Taehee Yoo.
This batch comes with is a conflict between 25fd386e0b ("netfilter:
core: add missing __rcu annotation") in your tree and 2c205dd398
("netfilter: add struct nf_nat_hook and use it") coming in this batch.
This conflict can be solved by leaving the __rcu tag on
__netfilter_net_init() - added by 25fd386e0b - and remove all code
related to nf_nat_decode_session_hook - which is gone after
2c205dd398, as described by:
diff --cc net/netfilter/core.c
index e0ae4aae96f5,206fb2c4c319..168af54db975
--- a/net/netfilter/core.c
+++ b/net/netfilter/core.c
@@@ -611,7 -580,13 +611,8 @@@ const struct nf_conntrack_zone nf_ct_zo
EXPORT_SYMBOL_GPL(nf_ct_zone_dflt);
#endif /* CONFIG_NF_CONNTRACK */
- static void __net_init __netfilter_net_init(struct nf_hook_entries **e, int max)
-#ifdef CONFIG_NF_NAT_NEEDED
-void (*nf_nat_decode_session_hook)(struct sk_buff *, struct flowi *);
-EXPORT_SYMBOL(nf_nat_decode_session_hook);
-#endif
-
+ static void __net_init
+ __netfilter_net_init(struct nf_hook_entries __rcu **e, int max)
{
int h;
I can also merge your net-next tree into nf-next, solve the conflict and
resend the pull request if you prefer so.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver updates 2018-05-21
The following updates are included in this driver update series:
- Fix the debug output for the max channels count
- Read (once) and save the port property registers during probe
- Remove the use of the comm_owned field
- Remove unused SFP diagnostic support indicator field
- Add ethtool --module-info support
- Add ethtool --show-ring/--set-ring support
- Update the driver in preparation for ethtool --set-channels support
- Add ethtool --show-channels/--set-channels support
- Update the driver to always perform link training in KR mode
- Advertise FEC support when using a KR re-driver
- Update the BelFuse quirk to now support SGMII
- Improve 100Mbps auto-negotiation for BelFuse parts
This patch series is based on net-next.
---
Changes since v1:
- Update the --set-channels support to the use of the combined, rx and
tx options as specified in the ethtool man page (in other words, don't
create combined channels based on the min of the tx and rx channels
specified).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After changing speed to 100Mbps as a result of auto-negotiation (AN),
some 10/100/1000Mbps SFPs indicate a successful link (no faults or loss
of signal), but cannot successfully transmit or receive data. These
SFPs required an extra auto-negotiation (AN) after the speed change in
order to operate properly. Add a quirk for these SFPs so that if the
outcome of the AN actually results in changing to a new speed, re-initiate
AN at that new speed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a quirk to make the BelFuse 1GBT-SFP06 part look like
a 1000baseX part, program the SFP PHY to support SGMII and 10/100/1000
baseT.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a KR re-driver is present, indicate the FEC support is available
during auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link training is always attempted when in KR mode, but the code is
structured to check if link training has been enabled before attempting
to perform it. Since that check will always be true, simplify the code
to always enable and start link training during KR auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to show and set the device channel configuration.
Changing the channel configuration will result in a device restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support being able to dynamically set/change the number of
Rx and Tx channels, update the code to:
- Move alloc and free of device memory into callable functions
- Move setting of the real number of Rx and Tx channels to device startup
- Move mapping of the RSS channels to device startup
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to show and set the number of the Rx and Tx ring
descriptors. Changing the ring configuration will result in a device
restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to get SFP module information using ethtool.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently sets an indication of whether the SFP supports, and
that the driver can obtain, diagnostics data. This isn't currently used
by the driver and the logic to set this indicator is flawed because the
field is cleared each time the SFP is checked and only set when a new SFP
is detected. Remove this field and the logic supporting it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huy Nguyen
Linus Torvalds
Heiner Kallweit
Lukas Wunner
Joonsoo Kim
Daniel Borkmann
David S. Miller
Mika Westerberg
Jakub Kicinski
Alexei Starovoitov
Laura Abbott
Mathieu Xhonneux
Omar Sandoval
Sandipan Das
Martin KaFai Lau
oulijun
Jason Gunthorpe
Kalderon, Michal
Tom Lendacky