Drivers which are going to use it will have to select it and use
imx_set_irq_fiq() to set FIQ mode for this interrupt.
Changes since V1:
- removed '#ifdef CONFIG_FIQ' from irqs.h
- renamed imx_set_irq_type() to imx_set_irq_fiq()
- made irqt unsigned
- fixed irq number check
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix some base address declaration by adding a cast.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This one adds definitions to configure RTCK pad (PE16) in primary and alternate
function. The RTCK Pin is used by one wire master controller and as JTAG Clock
return.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds macros to get CSCR upper, lower and additional registers.
These registers are needed to configure a chip select line. The offset
layouts of these Registers are identical on mx27 and mx31, hence we can
use the macros in generic way
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this adds convenience values usable by mxc_iomux_mode() to configure Pins of the
spi interfaces on mx31.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Needed for 8250 serial port and CS89x0 ethernet interface.
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch provides an ARM implementation of ioremap_wc().
We use different page table attributes depending on which CPU we
are running on:
- Non-XScale ARMv5 and earlier systems: The ARMv5 ARM documents four
possible mapping types (CB=00/01/10/11). We can't use any of the
cached memory types (CB=10/11), since that breaks coherency with
peripheral devices. Both CB=00 and CB=01 are suitable for _wc, and
CB=01 (Uncached/Buffered) allows the hardware more freedom than
CB=00, so we'll use that.
(The ARMv5 ARM seems to suggest that CB=01 is allowed to delay stores
but isn't allowed to merge them, but there is no other mapping type
we can use that allows the hardware to delay and merge stores, so
we'll go with CB=01.)
- XScale v1/v2 (ARMv5): same as the ARMv5 case above, with the slight
difference that on these platforms, CB=01 actually _does_ allow
merging stores. (If you want noncoalescing bufferable behavior
on Xscale v1/v2, you need to use XCB=101.)
- Xscale v3 (ARMv5) and ARMv6+: on these systems, we use TEXCB=00100
mappings (Inner/Outer Uncacheable in xsc3 parlance, Uncached Normal
in ARMv6 parlance).
The ARMv6 ARM explicitly says that any accesses to Normal memory can
be merged, which makes Normal memory more suitable for _wc mappings
than Device or Strongly Ordered memory, as the latter two mapping
types are guaranteed to maintain transaction number, size and order.
We use the Uncached variety of Normal mappings for the same reason
that we can't use C=1 mappings on ARMv5.
The xsc3 Architecture Specification documents TEXCB=00100 as being
Uncacheable and allowing coalescing of writes, which is also just
what we need.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit ae82cbfc8b. It
needs the new byteorder headers to be exported to userspace, and
they aren't yet -- and probably shouldn't be, at this point in the
2.6.27 release cycle (or ever, for that matter).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
mcbsp is confused as to what takes a physical or virtual address.
Fix the two instances where it gets it wrong.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
arch/arm/plat-mxc/clock.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/plat-omap/gpio.c: In function '_omap_gpio_init':
arch/arm/plat-omap/gpio.c:1492: error: 'omap_mpuio_device' undeclared (first use in this function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ordinarily, memory holes in flatmem still have a valid memmap and is safe
to use. However, an architecture (ARM) frees up the memmap backing memory
holes on the assumption it is never used. /proc/pagetypeinfo reads the
whole range of pages in a zone believing that the memmap is valid and that
pfn_valid will return false if it is not. On ARM, freeing the memmap breaks
the page->zone linkages even though pfn_valid() returns true and the kernel
can oops shortly afterwards due to accessing a bogus struct zone *.
This patch lets architectures say when FLATMEM can have holes in the
memmap. Rather than an expensive check for valid memory, /proc/pagetypeinfo
will confirm that the page linkages are still valid by checking page->zone
is still the expected zone. The lookup of page_zone is safe as there is a
limited range of memory that is accessed when calling page_zone. Even if
page_zone happens to return the correct zone, the impact is that the counters
in /proc/pagetypeinfo are slightly off but fragmentation monitoring is
unlikely to be relevant on an embedded system.
Reported-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes arm to use the new bcd2bin/bin2bcd functions instead
of the obsolete BCD_TO_BIN/BIN_TO_BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Taken from omap 97b705ad835f1481270c4b67b402d6e37fa8ad15:
ARM: OMAP: Misc compile fixes after syncing with mainline
Also fix 2430 smc91x to use IRQ_LOWLEVEL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the S3C2443 clock register definitions for selecting the EPLL
reference clock described by S3C2443_CLKSRC_EPLLREF.
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
[ben-linux@fluff.org: minor description fixes]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The first spi bus is registered with number 0, but
the board data says that the device on it is registered
on bus 1.
Move the spi bus to bus 1 to keep the compatibility with the
original board-support patches.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warnings in arch/arm/plat-s3c24xx/pwm.c:
warning: symbol 's3c_device_timer' was not declared. Should it be static?
warning: symbol 'pwm_calc_tin' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warnings in arch/arm/plat-s3c24xx/pwm-clock.c:
warning: symbol 'clk_timer_scaler' was not declared. Should it be static?
warning: symbol 'clk_timer_tclk' was not declared. Should it be static?
warning: symbol 'clk_timer_tdiv' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following problems spotted by sparse:
warning: symbol 's3c24xx_gpiolib_input' was not declared. Should it be static?
warning: symbol 's3c24xx_gpiolib_output' was not declared. Should it be static?
warning: symbol 's3c24xx_gpiolib_set' was not declared. Should it be static?
warning: symbol 's3c24xx_gpiolib_get' was not declared. Should it be static?
warning: symbol 'gpios' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse errors in arch/arm/mach-s3c2410/nor-simtec.c:
53:27: warning: symbol 'simtec_nor_pdata' was not declared. Should it be static?
77:13: warning: symbol 'nor_simtec_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
corgi, spitz and poodle have audio codecs on their primary I2C bus so
need to call pxa_set_i2c_info() to set it up during init. Tested on
spitz by Stanislav.
Reported-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Register UART1 on QNAP TS-209 and TS-409 because the PIC controller
is connected to it. This fixes a regression from 2.6.26.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The lm75 driver was recently converted to the new-style binding,
so now it can be loaded from the DNS-323 support code.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Tested-by: Tobias Poschwatta <tp@fonz.de>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Flash needs to be set up before we can try to read the MAC address
from there.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Kurobox Pro crashes when any of the PCI controller registers
are accessed. This patch adds a function to the Orion PCI handling
code that board support code can call to disable enumerating the
PCI bus entirely, and makes the Kurobox Pro PCI-related init code
call this function.
Signed-off-by: Per Andersson <avtobiff@gmail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Fix
arch/arm/mach-pxa/pxa300.c:94: error: 'CKEN_MMC3' undeclared here (not in a function)
when building for PXA300.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch against 2.6.27-rc3 does the following changes to FSG-3 setup code:
1) Enable RTC on FSG-3 (proper name is needed). This change is needed due to a recent change in i2c.
2) i variable is only used when compiling for big endian.
So move its declaration to ARMEB ifdef to silence the warning when compiling for LE.
Mailing list link:
http://lists.arm.linux.org.uk/lurker/message/20080813.091556.cae2917e.en.html
Signed-off-by: Tomasz Chmielewski <mangoo@wpkg.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CC arch/arm/mach-integrator/impd1.o
arch/arm/mach-integrator/impd1.c: In function `impd1_probe':
arch/arm/mach-integrator/impd1.c:408: warning: too few arguments for format
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
This patch removes CVS keywords that weren't updated for a long time.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Another fix of inconsistent shift of the LCD_BIAS_ACTIVE_* and
LCD_PCLK_EDGE_* is also included.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paulius Zaleckas
Darius Augulis
Luotao Fu
Gilles Chanteperdrix
Sascha Hauer
Linus Torvalds
Lennert Buytenhek
David Woodhouse
Russell King
Huang Weiyi
Jean-Christophe DUBOIS
Mel Gorman
Adrian Bunk
Harvey Harrison
Wei Shuai
Ben Dooks
Mark Brown
Nicolas Pitre
Martin Michlmayr
Per Andersson
Mike Rapoport
Tomasz Chmielewski
Eric Miao