This patch adds code to determine the APE firmware type and report this
along with the firmware version.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASPM workaround setting obtained from NVRAM only works with devices
older than 5717. This patch enforces the restriction.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the code to only manage the PCIe gphy power for
CPMU-less devices only. The CPMU takes over management for newer
chips.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy test register location has been repurposed for 5717+ devices.
This patch changes the code to avoid this location for these devices.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a TG3_FLG3_5717_PLUS flag to collectively describe
the set of changes in the ASIC that will apply to all future chip
revisions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSS flag needs to be turned off during tg3_close(). If the device
fails to allocate more than one MSI-X vector the next time the device is
brought up, transmits will fail.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 commit e712699734 entitled
"tg3: Preserve PCIe MPS setting for new devs" attempted to ensure the
PCIe link negotiated Maximum Payload Size (MPS) setting was 128 bytes
for all devices that didn't support higher speeds. The 5784 device was
mistakenly added to this list when it shouldn't have. This patch
removes the 5784 ASIC rev devices from that list.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrites the siano IR implementation. The previous implementation were
non-standard. As such, it has issues if more than one device registers IR,
as there used to have some static constants used during protocol decoding
phase. Also, it used to implement its on RAW decoder, and only for RC5.
The new code uses RC core subsystem for handling IR. This brings several
new features to the driver, including:
- Allow to dynamically replace the IR keycodes;
- Supports all existing raw decoders (JVC, NEC, RC-5, RC-6, SONY);
- Supports lirc dev;
- Doesn't have race conditions when more than one sms IR is
registered;
- The code size for the IR implementation is very small;
- it exports the IR features via /sys/class/rc.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a more standard way to name those tables, as they're currently used
by the script that coverts those tables to be loaded via userspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the proper gpio port for WinTV MiniStick, with the information provided
by Michael.
Thanks-to: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplifies the logic for handling firmware 1.20 RC messages, fixing the
logic.
While here, I tried to use a RC-6 remote controller from my TV set, but it
didn't work with dib0700. Not sure why, but maybe this never worked.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements change_protocol callback. With this change,
there's no need for an extra modprobe parameter to specify the
protocol. When a table is loaded (either from in-kernel rc-map
tables or via ir-keytable program), the driver will automatically
change the protocol, in order to work with the given table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having one big keytable with 2 protocols inside, break it
into two separate tables, being one for NEC and another for RC-5 variants,
and properly identify what variant should be used at the boards entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
a 250ms delay is too low for this device. It ends by producing false
repeat events. Increase the delay time to 500 ms to avoid troubles.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allows dvb-usb drivers to use rc-core, instead of the legacy
implementation.
No driver were ported yet to rc-core, so, some small adjustments
may be needed, when starting to migrate the drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch, yet trivial. It just move the RC properties
to a separate struct, in order to prepare the dvb-usb drivers to
use rc-core. There's no change on the behavior of the drivers.
With this change, it is possible to have both legacy and rc-core
based code inside the dvb-usb-remote, allowing a gradual migration
to rc-core, driver per driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb-usb has its own IR handle code. Now that we have a Remote
Controller subsystem, we should start using it. So, remove this
struct, in favor of the similar struct defined at the RC subsystem.
This is a big, but trivial patch. It is a 3 line delect, plus
lots of rename on several dvb-usb files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
RJ54N1CB0C is a Sharp camera sensor.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SH7724 datasheet specifies 480 pixels as the VOU maximum vertical resolution.
This is a bug in the datasheet, VOU also supports the full PAL resolution: 576
lines. Adjust the driver accordingly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using CEU with CSI2 on SH-Mobile requires some special configuration of the
former. We also have to switch from calling only one subdev .s_mbus_fmt and
.try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver
use count to prevent it from unloading, while in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to
several video clients and send data to the CEU or to the Image Signal
Processor. This patch implements a v4l2-subdevice driver for CSI-2 to be used
within the soc-camera framework, implementing the second subdevice in addition
to the actual video clients.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These formats belong to the standard format set, defined by the MIPI CSI-2
specification.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Endianness notation is meaningless for 8 bit YUYV codes. Switch pixel code
names to explicitly state the order of colour components in the data
stream.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the bits under staging/lirc/ buildable, and add a TODO note.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commonly found on several Hauppauge video capture devices.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Nb: this is a very trimmed-down lirc_imon, which only supports the
oldest generation of imon devices that don't do onboard signal decoding
like the most recent generation imon devices -- those are now supported
by the ir-core imon driver.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: fixed a few WARNING: please, no space before tabs]
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for the KWorld PlusTV 340U and KWorld UB345-Q ATSC
sticks, which are really the same device. The sticks have an eMPIA
em2870 usb bridge chipset, an LG Electronics LGDT3304 ATSC/QAM
demodulator and an NXP TDA18271HD tuner -- early versions of the 340U
have a a TDA18271HD/C1, later models and the UB435-Q have a C2.
The stick has been tested succesfully with both VSB_8 and QAM_256 signals.
Its using lgdt3304 support added to the lgdt3305 driver by a prior patch,
rather than the current lgdt3304 driver, as its severely lacking in
functionality by comparison (see said patch for details).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In dvb_dvr_release, there is a test dvbdev->users==-1, but users are
never negative. This error results in hung tasks:
task PC stack pid father
bash D ffffffffa000c948 0 3264 3170 0x00000000
ffff88003aec5ce8 0000000000000086 0000000000011f80 0000000000011f80
ffff88003aec5fd8 ffff88003aec5fd8 ffff88003b848670 0000000000011f80
ffff88003aec5fd8 0000000000011f80 ffff88003e02a030 ffff88003b848670
Call Trace:
[<ffffffff813dd4a5>] dvb_dmxdev_release+0xc5/0x130
[<ffffffff8107b750>] ? autoremove_wake_function+0x0/0x40
[<ffffffffa00013a2>] dvb_usb_adapter_dvb_exit+0x42/0x70 [dvb_usb]
[<ffffffffa0000525>] dvb_usb_exit+0x55/0xd0 [dvb_usb]
[<ffffffffa00005ee>] dvb_usb_device_exit+0x4e/0x70 [dvb_usb]
[<ffffffffa000a065>] af9015_usb_device_exit+0x55/0x60 [dvb_usb_af9015]
[<ffffffff813a3f05>] usb_unbind_interface+0x55/0x1a0
[<ffffffff81316000>] __device_release_driver+0x70/0xe0
...
So check against 1 there instead.
BTW why's the TODO there? Adding TODOs to the code without
descriptions is like adding nothing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC host and gadget drivers both define constants and structures in
private header files. Move all those definitions to linux/usb/video.h
where they can be shared by the two drivers (and be available for
userspace applications).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix comments. It is demodulator driver not DVB USB -bridge.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Matt Carlson
David S. Miller
Mauro Carvalho Chehab
Guennadi Liakhovetski
Guennadi Liakhovetski
Jarod Wilson
Michael Krufky
Jiri Slaby
Laurent Pinchart
Antti Palosaari