When checking whether or not a given frame needs to be
moved to be properly aligned to a 4-byte boundary, we
use & 4 which wasn't intended, this code should check
the lowest two bits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is expected that config interface will always succeed as mac80211
will only request what driver supports. The exception here is when a
device has rfkill enabled. At this time the rfkill state is unknown to
mac80211 and config interface can fail. When this happens we deal with
this error instead of printing a WARN.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix basic rates setting from association response"
introduced a copy/paste error.
Unfortunately, this not just leads to wrong data being passed
to the driver but is remotely exploitable for some hardware or
driver combinations.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently beacon loss detection triggers after a scan. A probe request
is sent and a message like this is printed to the log:
wlan0: beacon loss from AP 00:12:17:e7:98:de - sending probe request
But in fact there is no beacon loss, the beacons are just not received
because of the ongoing scan. Fix it by updating last_beacon after
the scan has finished.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove this unused Kconfig variable, which Intel apparently once
promised to make use of but never did.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM IE must not be shorter than 4 bytes, so verify that
when parsing it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the scan_sdata variable here is terribly wrong,
if there has never been a scan then we fail. However,
we need a bandaid...
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Fragmentation threshold (typo)
ieee80211_ioctl_siwfrag() sets the fragmentation_threshold to 2352
when frame fragmentation is to be disabled, yet the corresponding
'get' function tests for 2353 bytes instead.
This causes user-space tools to display a fragmentation threshold
of 2352 bytes even if fragmentation has been disabled.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Sunday 05 April 2009 11:29:38 Michael Buesch wrote:
> On Sunday 05 April 2009 11:23:59 Jaswinder Singh Rajput wrote:
> > With latest linus tree I am getting, .config file attached:
> >
> > [ 22.895051] r8169: eth0: link down
> > [ 22.897564] ADDRCONF(NETDEV_UP): eth0: link is not ready
> > [ 22.928047] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> > [ 22.982292] libvirtd used greatest stack depth: 4200 bytes left
> > [ 63.709879] wlan0: authenticate with AP 00:11:95:9e:df:f6
> > [ 63.712096] wlan0: authenticated
> > [ 63.712127] wlan0: associate with AP 00:11:95:9e:df:f6
> > [ 63.726831] wlan0: RX AssocResp from 00:11:95:9e:df:f6 (capab=0x471 status=0 aid=1)
> > [ 63.726855] wlan0: associated
> > [ 63.730093] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> > [ 74.296087] wlan0: no IPv6 routers present
> > [ 79.349044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 119.358200] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 179.354292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 259.366044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 359.348292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 361.953459] packagekitd used greatest stack depth: 4160 bytes left
> > [ 478.824258] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 598.813343] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 718.817292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 838.824567] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 958.815402] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1078.848434] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1198.822913] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1318.824931] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1438.814157] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1558.827336] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1678.823011] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1798.830589] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1918.828044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2038.827224] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2116.517152] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2158.840243] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2278.827427] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
>
>
> I think this message should only show if CONFIG_MAC80211_VERBOSE_DEBUG is set.
> It's kind of expected that we lose a beacon once in a while, so we shouldn't print
> verbose messages to the kernel log (even if they are KERN_DEBUG).
>
> And besides that, I think one can easily remotely trigger this message and flood the logs.
> So it should probably _also_ be ratelimited.
Something like this:
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Wext makes no assumptions about the contents of
data->txpower.fixed and data->txpower.value when
data->txpower.disabled is set, so do not update
the user-requested power level while disabling.
Also, when wext configures a really _fixed_ power
output [1], we should reject it instead of limiting it
to the regulatory constraint. If the user wants to set
a _limit_ [2] then we should honour that.
[1] iwconfig wlan0 txpower 20dBm fixed
[2] iwconfig wlan0 txpower 10dBm
This fixes
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1942
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently rx status for frames which are completed from reorder buffer
is taken from it's cb area which is not always right, cb is not holding
the rx status when driver uses mac80211's non-irq rx handler to pass it's
received frames. This results in dropping almost all frames from reorder
buffer when security is enabled by doing double decryption (first in hw,
second in sw because of wrong rx status). This patch copies rx status into
cb area before the frame is put into reorder buffer. After this patch,
there is a significant improvement in throughput with ath9k + WPA2(AES).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.
To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of stopping the entire AC queue when enabling aggregation
(which was only done for hardware with aggregation queues) buffer
the packets for each station, and release them to the pending skb
queue once aggregation is turned on successfully.
We get a little more code, but it becomes conceptually simpler and
we can remove the entire virtual queue mechanism from mac80211 in
a follow-up patch.
This changes how mac80211 behaves towards drivers that support
aggregation but have no hardware queues -- those drivers will now
not be handed packets while the aggregation session is being
established, but only after it has been fully established.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We just found a bug in zd1211rw where it would reject
packets in the ->tx() method but leave them modified,
which would cause retransmit attempts with completely
bogus skbs, eventually leading to a panic due to not
having enough headroom in those.
This patch adds a sanity check to mac80211 to catch
such driver mistakes; in this case we warn and drop
the skb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TX aggregation becomes operational, we do a number of steps:
1) print a debug message
2) wake the virtual queue
3) notify the driver
Unfortunately, 1) and 3) are only done if the driver is first to
reply to the aggregation request, it is, however, possible that the
remote station replies before the driver! Thus, unify the code for
this and call the new function ieee80211_agg_tx_operational in both
places where TX aggregation can become operational.
Additionally, rename the driver notification from
IEEE80211_AMPDU_TX_RESUME to IEEE80211_AMPDU_TX_OPERATIONAL.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_tx takes a struct ieee80211_tx_data argument, but only
uses a few of its members, namely 'skb' and 'sta'. Make that explicit,
so that less internal knowledge is required in ieee80211_tx_pending
and the possibility of introducing errors here is removed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pending packets code is quite incomprehensible, uses memory barriers
nobody really understands, etc. This patch reworks it entirely, using
the queue spinlock, proper stop bits and the skb queues themselves to
indicate whether packets are pending or not (rather than a separate
variable like before).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Internally, mac80211 requires the skb's queue mapping to be set
to the AC queue, not the virtual A-MPDU queue. This is not done
correctly currently, this patch moves the code down to directly
before the driver is invoked and adds a comment that it will be
moved into the driver later.
Since this requires __ieee80211_tx() to have the sta pointer,
make sure to provide it in ieee80211_tx_pending().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fragmentation currently uses an allocated array to store the
fragment skbs, and then keeps track of which have been sent
and which are still pending etc. This is rather complicated;
make it simpler by just chaining the fragments into skb->next
and removing from that list when sent. Also simplifies all
code that needs to touch fragments, since it now only needs
to walk the skb->next list.
This is a prerequisite for fixing the stored packet code,
which I need to do for proper aggregation packet storing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch ("mac80211: remove mixed-cell and userspace MLME code")
was too obvious to me, so obvious that a stupid bug crept in. The IBSS
RX function must be invoked for IBSS, of course, not anything != IBSS.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211 to not notify the rate control algorithm's
tx_status() method when reporting status for a packet that didn't go
through the rate control algorithm's get_rate() method.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add IEEE80211_HW_BEACON_FILTERING flag so that driver inform that it supports
beacon filtering. Drivers need to call the new function
ieee80211_beacon_loss() to notify about beacon loss.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When software scanning we need to disable power save so that all possible
probe responses and beacons are received. For hardware scanning assume that
hardware will take care of that and document that assumption.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separate beacon and rx path tracking in preparation for the beacon filtering
support. At the same time change ieee80211_associated() to look a bit simpler.
Probe requests are now sent only after IEEE80211_PROBE_IDLE_TIME, which
is now set to 60 seconds.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the timer is triggering every two seconds
(IEEE80211_MONITORING_INTERVAL). Decrease the timer to only trigger during
data idle periods to avoid waking up CPU unnecessary. The timer will
still trigger during idle periods, that needs to be fixed later.
There's also a functional change that probe requests are sent only when the
data path is idle, earlier they were sent also while there was activity
on the data path.
This is also preparation for the beacon filtering support. Thanks to
Johannes Berg for the idea.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Neither can currently be set from userspace, so there's no
regression potential, and neither will be supported from
userspace since the new userspace APIs allow the SME, which
is in userspace, to control all we need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this. In addition, make the error values consistent by using
EOPNOTSUPP instead of semi-random assortment of errno values.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this or to be prepared to handle these commands when the interface is
down.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functionality that NL80211_CMD_SET_MGMT_EXTRA_IE provided can now
be achieved with cleaner design by adding IE(s) into
NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, and
NL80211_CMD_DISASSOCIATE.
Since this is a very recently added command and there are no known (or
known planned) applications using NL80211_CMD_SET_MGMT_EXTRA_IE and
taken into account how much extra complexity it adds to the IE
processing we have now (and need to add in the future to fix IE order
in couple of frames), it looks like the best option is to just remove
the implementation of this command for now. The enum values themselves
are left to avoid changing the nl80211 command or attribute numbers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This file was forgotten from the quilt patch that added MLME
primitives, so the kfree on interface removal is missing. Fix this
potential memleak by freeing the temporary Authentication frame IEs
from SME when the interface is being removed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 resumes, it currently doesn't reconfigure the interfaces
entirely and also doesn't reconfigure BSS information -- fix this.
Also, to be able to test this, add a debugfs file that just calls
the suspend/resume code to see what happens when we go through that,
without needing the time-consuming suspend/resume cycle.
(Original version broke the build for CONFIG_PM=n. Define alternative
functions for that situation. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new nl80211 commands to allow user space to request
authentication and association (and also deauthentication and
disassociation). The commands are structured to allow separate
authentication and association steps, i.e., the interface between
kernel and user space is similar to the MLME SAP interface in IEEE
802.11 standard and an user space application takes the role of the
SME.
The patch introduces MLME-AUTHENTICATE.request,
MLME-{,RE}ASSOCIATE.request, MLME-DEAUTHENTICATE.request, and
MLME-DISASSOCIATE.request primitives. The authentication and
association commands request the actual operations in two steps
(assuming the driver supports this; if not, separate authentication
step is skipped; this could end up being a separate "connect"
command).
The initial implementation for mac80211 uses the current
net/mac80211/mlme.c for actual sending and processing of management
frames and the new nl80211 commands will just stop the current state
machine from moving automatically from authentication to association.
Future cleanup may move more of the MLME operations into cfg80211.
The goal of this design is to provide more control of authentication and
association process to user space without having to move the full MLME
implementation. This should be enough to allow IEEE 802.11r FT protocol
and 802.11s SAE authentication to be implemented. Obviously, this will
also bring the extra benefit of not having to use WEXT for association
requests with mac80211. An example implementation of a user space SME
using the new nl80211 commands is available for wpa_supplicant.
This patch is enough to get IEEE 802.11r FT protocol working with
over-the-air mechanism (over-the-DS will need additional MLME
primitives for handling the FT Action frames).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 event notifications (and a new multicast group, "mlme")
for informing user space about received and processed Authentication,
(Re)Association Response, Deauthentication, and Disassociation frames in
station and IBSS modes (i.e., MLME SAP interface primitives
MLME-AUTHENTICATE.confirm, MLME-ASSOCIATE.confirm,
MLME-REASSOCIATE.confirm, MLME-DEAUTHENTICATE.indicate, and
MLME-DISASSOCIATE.indication). The event data is encapsulated as the 802.11
management frame since we already have the frame in that format and it
includes all the needed information.
This is the initial step in providing MLME SAP interface for
authentication and association with nl80211. In other words, kernel code
will act as the MLME and a user space application can control it as the
SME.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must not clear the previous BSSID when roaming to another AP within
the same ESS for reassociation to be used properly. It is fine to
clear this when the SSID changes, so let's move the code into
ieee80211_sta_set_ssid().
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_tx_h_check_assoc() was dropping everything else than probe
requests during software scan. So the nullfunc frame with the power save
bit was dropped and AP never received it. This meant that AP never
buffered any frames for the station during software scan.
Fix this by allowing to transmit both probe request and nullfunc frames
during software scan. Tested with stlc45xx.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver has been notified with a STA_REMOVE, it tears down
the internal ADDBA state. On resume, trying to initiate aggregation would
fail because mac80211 has not cleared the operational state for that <TID,STA>.
This can be fixed by tearing down the existing sessions on a suspend.
Also, the driver can initiate a new BA session when suspend is in progress.
This is fixed by marking the station as being in suspend state and
denying ADDBA requests for such STAs.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To avoid concurrent manipulations of the sta list (which shouldn't
be possible at this point, but anyway) we need to hold the sta_lock
around iterating the list.
At the same time, we do not need to iterate the list at all if
the driver doesn't want to be notified.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radiotap was updated to include a "bad PLCP" flag and standardise
the "bad FCS" flag in the "flags" rather than "RX flags" field,
this patch updates Linux to that standard.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even though userland probably cannot submit packets, there might
still be some coming, and that's no good when the driver doesn't
expect them. Stop the queues across suspend/resume.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last warning can never trigger, and the explicit AP_VLAN
check is pointless if we move the config_interface check down,
in practice config_interface is required anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a scan is queued in STA mode while the interface is in state direct
probe, authenticate or associate the scan is delayed until the interface
enters disabled or associated state. But in case of direct probe-,
authentication- or association- timeout sta_work will not be scheduled
anymore (without external trigger) and thus the pending scan is not
executed and prevents a new scan from being triggered (-EBUSY).
Fix this by queueing the sta work again after direct probe-, authentication-
and association- timeout.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This inline is useless and actually makes the code _longer_
rather than shorter.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't call ieee80211_sta_find_ibss() directly, like it's done in STA
mode, so that the commit() call is more harmless respectively has
less site-effects.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even after commit "mac80211: deauth when interface is marked down"
(e327b847 on Linus tree), userspace still isn't notified when interface
goes down. There isn't a problem with this commit, but because of other
code changes it doesn't work on kernels >= 2.6.28 (works if same/similar
change applied on 2.6.27 for example).
The issue is as follows: after commit "mac80211: restructure disassoc/deauth
flows" in 2.6.28, the call to ieee80211_sta_deauthenticate added by
commit e327b847 will not work: because we do sta_info_flush(local, sdata)
inside ieee80211_stop (iface.c), all stations in interface are cleared, so
when calling ieee80211_sta_deauthenticate->ieee80211_set_disassoc (mlme.c),
inside ieee80211_set_disassoc we have this in the beginning:
sta = sta_info_get(local, ifsta->bssid);
if (!sta) {
The !sta check triggers, thus the function returns early and
ieee80211_sta_send_apinfo(sdata, ifsta) later isn't called, so
wpa_supplicant/userspace isn't notified with SIOCGIWAP.
This commit moves deauthentication to before flushing STA info
(sta_info_flush), thus the above can't happen and userspace is really
notified when interface goes down.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfg80211 requests a scan it awaits either a return code != 0 from
the scan function or the cfg80211_scan_done to be called. In case of
a STA mac80211's scan function ever returns 0 and queues the scan request.
If ieee80211_sta_work is executed and ieee80211_start_scan fails for
some reason cfg80211_scan_done will never be called but cfg80211 still
thinks the scan was triggered successfully and will refuse any future
scan requests due to drv->scan_req not being cleaned up.
If a scan is triggered from within the MLME a similar problem appears. If
ieee80211_start_scan returns an error, local->scan_req will not be reset
and mac80211 will refuse any future scan requests.
Hence, in both cases call ieee80211_scan_failed (which notifies cfg80211
and resets local->scan_req) if ieee80211_start_scan returns an error.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg
Reinette Chatre
Kalle Valo
Robert P. J. Day
Gerrit Renker
Michael Buesch
Vasanthakumar Thiagarajan
Matt LaPlante
Kalle Valo
Jouni Malinen
Sujith
Helmut Schaa
Alina Friedrichsen
David S. Miller
Herton Ronaldo Krzesinski