These instructions were placed in the code directly as opcodes because
early compilers didn't support them. Toolchains supporting ARMv7
understand these instructions and the patch puts the mnemonics back.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... including some comments about the ordering required to bring
sparsemem up. You have to repeatedly guess, test, reguess, try
again and again to work out what the right ordering is. Many
hours later...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide helpers for getting physical addresses or pfns from the
meminfo array, and use them. Move for_each_nodebank() to
asm/setup.h alongside the meminfo structure definition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of the previous commit, MT_DEVICE_IXP2000 encodes to the same
PTE bit encoding as MT_DEVICE, so it's now redundant. Convert
MT_DEVICE_IXP2000 to use MT_DEVICE instead, and remove its aliases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide L_PTE_MT_xxx definitions to describe the memory types that we
use in Linux/ARM. These definitions are carefully picked such that:
1. their LSBs match what is required for pre-ARMv6 CPUs.
2. they all have a unique encoding, including after modification
by build_mem_type_table() (the result being that some have more
than one combination.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are actually only four separate implementations of set_pte_ext.
Use assembler macros to insert code for these into the proc-*.S files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no point scattering this around the tree, the parsing
of the parameter might as well live beside the code which uses
it. That also means we can make vmalloc_reserve a static
variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The newly introduced sanity_check_meminfo() function should be
used to collect all validation of the meminfo array, which we
have in bootmem_init(). Move it there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Make sure that coprocessor instructions for range ops are contiguous
and not reordered.
- s/invalidate_and_disable_dcache/flush_and_disable_dcache/
- Don't re-enable I/D caches if they were not enabled initially.
- Change some masks to shifts for better generated code.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
The PTRS_PER_PMD != 1 condition can be evaluated with C code and
optimized at compile time.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per the dma_unmap_* calls, we don't touch the cache when a DMA
buffer transitions from device to CPU ownership. Presently, no
problems have been identified with speculative cache prefetching
which in itself is a new feature in later architectures. We may
have to revisit the DMA API later for these architectures anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Feroceon L2 cache can work in eighther write through or write back mode
on Kirkwood. Add the option to configure this mode according to Kconfig.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch provides an ARM implementation of ioremap_wc().
We use different page table attributes depending on which CPU we
are running on:
- Non-XScale ARMv5 and earlier systems: The ARMv5 ARM documents four
possible mapping types (CB=00/01/10/11). We can't use any of the
cached memory types (CB=10/11), since that breaks coherency with
peripheral devices. Both CB=00 and CB=01 are suitable for _wc, and
CB=01 (Uncached/Buffered) allows the hardware more freedom than
CB=00, so we'll use that.
(The ARMv5 ARM seems to suggest that CB=01 is allowed to delay stores
but isn't allowed to merge them, but there is no other mapping type
we can use that allows the hardware to delay and merge stores, so
we'll go with CB=01.)
- XScale v1/v2 (ARMv5): same as the ARMv5 case above, with the slight
difference that on these platforms, CB=01 actually _does_ allow
merging stores. (If you want noncoalescing bufferable behavior
on Xscale v1/v2, you need to use XCB=101.)
- Xscale v3 (ARMv5) and ARMv6+: on these systems, we use TEXCB=00100
mappings (Inner/Outer Uncacheable in xsc3 parlance, Uncached Normal
in ARMv6 parlance).
The ARMv6 ARM explicitly says that any accesses to Normal memory can
be merged, which makes Normal memory more suitable for _wc mappings
than Device or Strongly Ordered memory, as the latter two mapping
types are guaranteed to maintain transaction number, size and order.
We use the Uncached variety of Normal mappings for the same reason
that we can't use C=1 mappings on ARMv5.
The xsc3 Architecture Specification documents TEXCB=00100 as being
Uncacheable and allowing coalescing of writes, which is also just
what we need.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/kernel/process.c:270:6: warning: symbol 'show_fpregs' was not declared. Should it be static?
This function isn't used, so can be removed.
arch/arm/kernel/setup.c:532:9: warning: symbol 'len' shadows an earlier one
arch/arm/kernel/setup.c:524:6: originally declared here
A function containing two 'len's.
arch/arm/mm/fault-armv.c:188:13: warning: symbol 'check_writebuffer_bugs' was not declared. Should it be static?
arch/arm/mm/mmap.c:122:5: warning: symbol 'valid_phys_addr_range' was not declared. Should it be static?
arch/arm/mm/mmap.c:137:5: warning: symbol 'valid_mmap_phys_addr_range' was not declared. Should it be static?
Missing includes.
arch/arm/kernel/traps.c:71:77: warning: Using plain integer as NULL pointer
arch/arm/mm/ioremap.c:355:46: error: incompatible types in comparison expression (different address spaces)
Sillies.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This declaration specifies the "function" type and size for various
assembly functions, mainly needed for generating the correct branch
instructions in Thumb-2.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than pollute asm/cacheflush.h with the cache type definitions,
move them to asm/cachetype.h, and include this new header where
necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add asm/cputype.h, moving functions and definitions from asm/system.h
there. Convert all users of 'processor_id' to the more efficient
read_cpuid_id() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch will truncate and/or ignore memory banks if their kernel
direct mappings would (partially) overlap with the vmalloc area or
the mappings between the vmalloc area and the address space top, to
prevent crashing during early boot if there happens to be more RAM
installed than we are expecting.
Since the start of the vmalloc area is not at a fixed address (but
the vmalloc end address is, via the per-platform VMALLOC_END define),
a default area of 128M is reserved for vmalloc mappings, which can
be shrunk or enlarged by passing an appropriate vmalloc= command line
option as it is done on x86.
On a board with a 3:1 user:kernel split, VMALLOC_END at 0xfe000000,
two 512M RAM banks and vmalloc=128M (the default), this patch gives:
Truncating RAM at 20000000-3fffffff to -35ffffff (vmalloc region overlap).
Memory: 512MB 352MB = 864MB total
On a board with a 3:1 user:kernel split, VMALLOC_END at 0xfe800000,
two 256M RAM banks and vmalloc=768M, this patch gives:
Truncating RAM at 00000000-0fffffff to -0e7fffff (vmalloc region overlap).
Ignoring RAM at 10000000-1fffffff (vmalloc region overlap).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Riku Voipio <riku.voipio@iki.fi>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform independent header files to arch/arm/include/asm, leaving
those in asm/arch* and asm/plat* alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Claim the initrd memory exclusively, and order other memory
reservations beforehand. This allows us to determine whether
the initrd memory was overwritten, and disable the initrd in
that case.
This avoids a 'bad page state' bug.
Tested-by: Ralph Siemsen <ralphs@netwinder.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(20072fd0c9 lost most of its changes
somehow, came from a mbox archive applied with git-am. No idea
what happened. This puts back the missing bits. --rmk)
The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.
This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.
CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:
a. _only_ PXA300/PXA310 support included and no L2 cache wanted
b. PXA320 support included, but want L2 be disabled
So the enabling of L2 depends on two things:
- CACHE_XSC3L2 is selected
- and L2 cache is present
Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).
IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.
Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:
- OC bits in TTBASE register (table walk outer cache attributes)
- LLR Outer Cache Attributes (OC) in Auxiliary Control Register
Signed-off-by: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems this small label was lost in the last merge. Without it
no CPU type is selected for the MX2 family of processors. And a build
will fail badly...
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The shared mmap code works fine for the test case, which only checked
for two shared maps of the same file. However, three shared maps
result in one mapping remaining cached, resulting in stale data being
visible via that mapping. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
free_area_init_node() gets passed in the node id as well as the node
descriptor. This is redundant as the function can trivially get the node
descriptor itself by means of NODE_DATA() and the node's id.
I checked all the users and NODE_DATA() seems to be usable everywhere
from where this function is called.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a lot of places that define either a single bootmem descriptor or an
array of them. Use only one central array with MAX_NUMNODES items instead.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russell King
Catalin Marinas
Nicolas Pitre
Ronen Shitrit
Lennert Buytenhek
Linus Torvalds
Eric Miao
Ingo Molnar
Sascha Hauer
Johannes Weiner
Dmitry Baryshkov