According to Atmel, their 926T processors (AT91 post RM9200) requires
'Wait for Interrupt' mode be entered right after disabling the processor clock
in order to minimise current consumption when idle, so do both provided we're
not running on a 920T (an RM9200).
Furthermore, get rid of the #ifndef CONFIG_DEBUG_KERNEL, since arch_idle()
can be turned off completely with the kernel parameter 'nohlt'.
Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use a correct udelay value to get bus speed around 100KHz. The udelay
value was most likely copied from the older devices, but the 9g45
is signicantly faster (400MHz, DDR, ..), so a udelay of 2 gives a
bus speed of around 190KHz, which is too fast for some devices.
A udelay value of 5 gives a bus speed of around 90KHz here.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sd/mmc data structure is not used if SPI is selected. The configuration
of PIO on the board prevent from using both interfaces at the same time
(board dependent).
Remove the warnings at compilation time adding a preprocessor condition.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add information in dm9000 mac/phy chip initialization:
- irq resource details
- platform data details
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Without this patch you will not be able to register the first block
because of the second association call on at91_add_device_tc().
Signed-off-by: Fabian Godehardt <fg@emlix.com>
[nicolas.ferre@atmel.com: change tcb1_clk to fake child clock of tcb0_clk]
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
While registering clock allow to set parent clock other
than mck. It is useful for clocks than can be seen as
child clock of a peripheral.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 12/19] ARM: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
Date: Thu, 5 Aug 2010 16:08:46 +0200
Message-Id: <1281017333-5563-12-git-send-email-u.kleine-koenig@pengutronix.de>
These two structs are referenced by cam60_spi_devices. The latter is
copied at init time to kmalloced memory and so the copy isn't freed after
booting. So it must not contain references to .init memory.
This isn't noticed by modpost as cam60_spi_devices is in .init.data, too.
Noticed-and-Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cam60_spi_devices is passed to at91_add_device_spi which calls
spi_register_board_info. The latter makes a copy of it, so living in
.init.data is OK.
This fixes the following warning in cam60_defconfig:
WARNING: vmlinux.o(.data+0x2a00): Section mismatch in reference from the variable cam60_spi_devices to the (unknown reference) .init.data:(unknown)
The variable cam60_spi_devices references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the vbus signal to optionally use polling. This is required if
the vbus signal is connected to an non-interrupting io expander for
example. If vbus is in polling mode, then it is assumed that the vbus
gpio may sleep. Also add an option to have vbus be an active low
signal. Both options are set in the platform data for the device.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Bluewater Systems Snapper 9260/9G20 modules
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add definition for NR_BUILTIN_GPIO for AT91 family
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This rework allows to address tow memory controllers. AT91SAM9263 and
AT91SAM9G45 family have tow SDRAM or DDR/SDRAM controllers. Power management
should take care of this.
This patch modify the way RAM IP header files are implemented to allow
access to registers of both controllers ; it also adds some macros.
We also modify the power management files to use those modified header files.
Slow clock (assembly) and regular power management functions are synchronized
for setting of RAM self-refresh procedure:
(lpr & ~AT91_DDRSDRC_LPCB) | AT91_DDRSDRC_LPCB_SELF_REFRESH
Note that AT91RM9200 is not impacted by this modification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is the basic support for at91sam9g46, at91sam9m10 and at91sam9m11. Those
are just very basic cpu macros and clock definition.
Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-at91/board-sam9m10g45ek.c: mach/hardware.h is included more than once
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Final version of the patch that adds support for RS485 communications to the atmel_serial driver.
The patch has been already sent and discussed on both linux-kernel and linux-arm-kernel mailing lists several times.
Many people collaborated to improve and test the code:
Tested-by: Sebastian Heutling <Sebastian.Heutling@who-ing.de>
Tested-by: Bernhard Roth <br@pwrnet.de>
Reviewed-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Rick Bronson <rick@efn.org>
Signed-off-by: Sebastian Heutling <Sebastian.Heutling@who-ing.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Disable the processor clock when the CPU is idle.
This saves much more power than merely entering 'Wait for Interrupt' mode.
Since JTAG-debugging doesn't work when the processor clock is switched off,
make it conditional on CONFIG_DEBUG_KERNEL.
Signed-off-by: Anders Larsen <al@alarsen.net>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A bit in the at91sam9g10 identification number changed between Engineering
Sample and final product. This patch will identify both as being at91sam9g10.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both boards share the same board file, as the PortuxG20 is basically an
SBC based on the Stamp9G20.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cosmetic change to mach-at91 Makefile: remove two blanks introduced
by earlier patches.
Signed-off-by: Ernst Schwab <eschwab@online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Julien Langer <julien.langer@gmail.com>
AT91: when turning off the PLLs during suspend, don't wait for the lock
flag to be set. Previously the code would always run into the loop
limitation of 1000 iterations because the flag is never set when turning
the PLLs off.
Comments from Anders Larsen:
(in http://marc.info/?l=linux-kernel&m=127058929724193&w=2)
Signed-off-by: Julien Langer <julien.langer@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
at91 slow-clock resume: Don't wait for a disabled PLL to lock.
We run into this problem with the PLLB on the at91: ohci-at91 disables
the PLLB when going to suspend. The slowclock code however tries to do
the same: It saves the PLLB register value and when restoring the value
during resume, it waits for the PLLB to lock again. However the PLL will
never lock and the loop would run into its timeout because the slowclock
code just stored and restored an empty register.
This fixes the problem by only restoring PLLA/PLLB when they were enabled
at suspend time.
Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert arm to use GENERIC_TIME via the arch_getoffset() infrastructure,
reducing the amount of arch specific code we need to maintain.
The arm architecture is the last arch that need to be converted.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
The change introduced in patch 5596/1 used incorrect bracing which
resulted in the AT24 EEPROM no longer being registered. This patch
corrects the bracing and allows both the WM8731 audio device and AT24
EEPROM device to be registered.
Signed-off-by: Rob Alley <rob.alley@navmanwireless.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some misspelled occurences of 'octet' and some comments were also fixed
as I was on it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
on AT91 the timer irq is shared, so the handler might be entered without
irqs being disabled. Though this should not happen as the timer irq is
registered early, there have been some reports on the mailing list.
To make debugging that problem easier next time it pops up a
WARN_ON_ONCE is added to the handler if irqs are not off.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Add support for the Atmel AT572D940HF-EK board (development board for
the AT572D940HF processor).
Signed-off-by: Antonio R. Costa <costa.antonior@gmail.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT572D940HF processor (DIOPSIS range).
This processor integrates an ARM926 core, a DSP and the SoC
peripherals usually found on an AT91 processor (USART, SSC, SPI, TWI,
CAN, etc)
Signed-off-by: Antonio R. Costa <costa.antonior@gmail.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the use of another DMA controller driver in atmel-mci sd/mmc driver.
This adds a generic dma_slave pointer to the mci platform structure where
we can store DMA controller information. In atmel-mci we use information
provided by this structure to initialize the driver (with new helper
functions that are architecture dependant).
This also adds at32/avr32 chip modifications to cope with this new access
method.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
New at91sam9g45ekes board provides a LCD with resistive touchscreen.
This is the support of this feature by atmel_tsadcc driver. This also
sets up platform parameters to be passed to the driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Setup platform parameters in at91sam9rl-ek board to be passed to
atmel_tsadcc touchscreen.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.
Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Many Atmel SOC are embedding a LCD controller. This patch removes the long
dependency line for this Atmel LCD framebuffer driver configuration entry.
The HAVE_FB_ATMEL configuration option is located in the video Kconfig file
as it may be setup by ARM/AT91 and AVR32 chips.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Instead of adding "depends on" at config level, introduce HAVE_* config
variables. Add them at machine or soc level to specify the ability of a
particular support.
It will ease new board introduction and readability.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Those "depends on" are a double check as all machine entries are
surrounded by "if <ARCH_xxx>" conditions.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Anders Larsen
Peter Korsgaard
Nicolas Ferre
Fabian Godehardt
Uwe Kleine-König
Ryan Mallon
Dmitry Eremin-Solenikov
Andrea Gelmini
Russell King
Claudio Scordino
Christian Glindkamp
Ernst Schwab
John Stultz
Rob Alley
Linus Torvalds
Jiri Kosina
Tony Lindgren
Daniel Mack
Andrew Victor
Dmitry Torokhov
Jean-Christophe PLAGNIOL-VILLARD