This patch adds PCI bridge support for the Marvell mv64x60 chip.
We also provide the ability to read/write the mv64x60 hotswap
register via sysfs if the hs_reg_valid property is set in the
device tree.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
MPSC (multi-protocol serial controller) ports, based on information
contained in the device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are 3 interrupt groups each with its own status/mask registers.
We use a separate struct irq_chip for each interrupt group and handle
interrupts in two stages or levels: level 1 selects the appropriate
struct irq_chip, and level 2 selects individual interrupts within
that irq_chip.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc_flash_init() implements a broken way of probing for flash
devices supported by the physmap_of driver. It finds all nodes in the
device tree with device_type=="rom" and instantiates of_platform
devices for them. This is fundamentally incompatible with the normal
and correct way of probing for of_platform_bus_probe(). Platforms
which relied on powerpc_flash_init()s behaviour (none are in-tree)
will have to update their platform probing code to correctly probe
busses containing flash devices.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MPIC U3/U4 MSI backend. Based on code from Segher, heavily hacked by me.
This only deals with MSI on U3/U4 MPICs, aka. CPC 9x5.
If we find a U3/U4 then we enable this backend, ie. take over the ppc_md
MSI hooks. We might need more elaborate logic in future to decide which
backend is enabled.
We need our own irq_chip so that we can do MSI masking/unmasking on
the device itself. We also need to mask explicitly on shutdown to make
sure we don't get bitten by lazy-disable semantics.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To support MSI on MPIC we need a way to reserve and allocate hardware irq
numbers, this patch implements an allocator for that purpose.
New firmware platforms must define a "msi-available-ranges" property on their
MPIC node for MSI to work. For U3/U4 we do a best-guess setup.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a driver to arch/powerpc/sysdev for the UIC, the
on-chip interrupt controller from IBM/AMCC 4xx chips. It uses the new
irq host mapping infrastructure.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This move sets the stage for the use of generic PCI Express
code in 85xx and 86xx parts from FSL. Subsequent patches
for 8548 and 8544 will be able to use this shared code.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This removes the time suspend/restore code that was done through
a PMU notifier in arch/platforms/powermac/time.c.
Instead, introduce arch/powerpc/sysdev/timer.c which creates a sys
device and handles time of day suspend/resume through that.
This should probably be replaced by using the generic RTC framework
but for now it gets rid of the arcane powermac specific hack.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds driver code for the PMI device found in future IBM products.
PMI stands for "Platform Management Interrupt" and is a way to
communicate with the BMC (Baseboard Management Controller).
It provides bidirectional communication with a low latency.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Heiko J Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This covers common CPM access functions, CPM interrupt controller code,
micropatch and a few compatibility things to kee the same driver base
working with arch/ppc. This version is refined with all the comments
(mostly PIC-related) addressed.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
sysdev/rom.c is for arch/powerpc only. Don't compile it when building
an arch/ppc kernel.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 85xx we don't build in dcr support because the core doesn't implement the
instructions. This caused problems when building an 85xx kernel. Additionally
made it so we only build __mtdcr/__mfdcr if we are CONFIG_PPC_DCR_NATIVE.
The 85xx build issue wasPointed out by Dai Haruki.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
No other chips use this device, it belongs in a 52xx-specific path.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for flash device descriptions to the OF device tree.
It's inspired by and partially borrowed from Sergei's patch "[RFC]
Adding MTD to device tree.patch".
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/mpc52xx_pic.c breaks the ppc build
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds new dcr_map/dcr_read/dcr_write accessors for DCRs that
can be used by drivers to transparently address either native DCRs or
memory mapped DCRs. The implementation for memory mapped DCRs is done
after the binding being currently worked on for SLOF and the Axon
chipset. This patch enables it for the cell native platform
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for the MPC52xx Interrupt controller for
ARCH=powerpc.
It includes the main code in arch/powerpc/sysdev/ as well as a header
file in include/asm-powerpc.
Signed-off-by: Nicolas DET <nd@bplan-gmbh.de>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apparently we've copied the todc drivers, for various RTCs used in
embedded machines from ARCH=ppc to ARCH=powerpc, despite the fact that
it's never used in the latter. This patch removes it.
If we ever need these drivers (which we probably shouldn't now the RTC
class stuff is in), we can transfer them one by one from ARCH=ppc,
removing from the hideous abomination which is the todc
"infrastructure".
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add QUICC Engine (QE) configuration, header files, and
QE management and library code that are used by QE devices
drivers.
Includes Leo's modifications up to, and including, the
platform_device to of_device adaptation:
"The series of patches add generic QE infrastructure called
qe_lib, and MPC8360EMDS board support. Qe_lib is used by
QE device drivers such as ucc_geth driver.
This version updates QE interrupt controller to use new irq
mapping mechanism, addresses all the comments received with
last submission and includes some style fixes.
v2: Change to use device tree for BCSR and MURAM;
Remove I/O port interrupt handling code as it is not generic
enough.
v3: Address comments from Kumar; Update definition of several
device tree nodes; Copyright style change."
In addition, the following changes have been made:
o removed typedefs
o uint -> u32 conversions
o removed following defines:
QE_SIZEOF_BD, BD_BUFFER_ARG, BD_BUFFER_CLEAR, BD_BUFFER,
BD_STATUS_AND_LENGTH_SET, BD_STATUS_AND_LENGTH, and BD_BUFFER_SET
because they hid sizeof/in_be32/out_be32 operations from the reader.
o fixed qe_snums_init() serial num assignment to use a const array
o made CONFIG_UCC_FAST select UCC_SLOW
o reduced NR_QE_IC_INTS from 128 to 64
o remove _IO_BASE, etc. defines (not used)
o removed irrelevant comments, added others to resemble removed BD_ defines
o realigned struct definitions in headers
o various other style fixes including things like pinMask -> pin_mask
o fixed a ton of whitespace issues
o marked ioregs as __be32/__be16
o removed platform_device code and redundant get_qe_base()
o removed redundant comments
o added cpu_relax() to qe_reset
o uncasted all get_property() assignments
o eliminated unneeded casts
o eliminated immrbar_phys_to_virt (not used)
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the cpm2 common code and PIC stuff to the powerpc. Most of the files
were just copied from ppc/, with minor tuning to make it compile, and, subsequently, work.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Keep from breaking 83xx arch/ppc build. Back up old school arch/powerpc/sysdev/ipic.[hc] to arch/ppc/syslib.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This copies the i8259 interrupt controller driver from arch/powerpc
to arch/ppc. It's currently shared by both architectures, but the upcoming
arch/powerpc interrupt changes will break the arch/ppc builds. The changes
are too important to just use #ifdef's in the driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a resubmit with a proper subject and with all comments addressed.
Applies cleanly to powerpc.git 649e857972
Mark
--
The todc code from arch/ppc supports many todc/rtc chips and is needed
in arch/powerpc. This patch adds the todc code to arch/powerpc.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
--
arch/powerpc/Kconfig | 7
arch/powerpc/sysdev/Makefile | 1
arch/powerpc/sysdev/todc.c | 392 ++++++++++++++++++++++++++++++++++
include/asm-powerpc/todc.h | 487 +++++++++++++++++++++++++++++++++++++++++++
4 files changed, 887 insertions(+)
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add Tundra Semiconductor tsi108 pci and platform device data register
function support.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
---
Signed-off-by: Paul Mackerras <paulus@samba.org>
Micro-optimisation - add no-minimal-toc to some more arch/powerpc Makefiles.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Parse the flat device tree for devices on Freescale SOC's that we know
about (gianfar, gianfar_mdio, i2c, mpc83xx_wdt). We need to setup
platform devices and platform data for these devices to match arch/ppc
usage.
Also add a helper function (get_immrbase) that reports the base
address of the MMIO registers on the SOC.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated Kconfig & Makefiles in prep for adding support for the Freescale
MPC83xx family of processors to arch/powerpc. Moved around some config
options that are more globally applicable to other PowerPC processors.
Added a temporary config option (83xx) to match existing arch/ppc support
for the MPC83xx line.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental ! There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved 83xx and QUICC Engine interrupt handling code into arch/powerpc
as a precursor of getting 83xx sub-arch building in arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The nvram code formally known as bpa_nvram.c is rather
generic really, so it is quite likely to be useful to
future boards not based on cell.
This patch puts it into arch/powerpc/sysdev.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is so that the 32-bit CHRP code can use it. The MPC106
initialization code is now in arch/powerpc/sysdev/grackle.c and
is controlled by CONFIG_PPC_MPC106.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the parameters for i8259_init so that it takes two
parameters: a physical address for generating an interrupt
acknowledge cycle, and an interrupt number offset. i8259_init
now sets the irq_desc[] for its interrupts; all the callers
were doing this, and that code is gone now. This also defines
a CONFIG_PPC_I8259 symbol to select i8259.o for inclusion, and
makes the platforms that need it select that symbol.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This defines a CONFIG_INDIRECT_PCI symbol to control whether it
gets used or not, and fixes the Kconfig to select that symbol for
platforms that need it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also puts a copy of indirect_pci.c in arch/powerpc/sysdev
so that we don't need to build in arch/ppc/syslib.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Dale Farnsworth
David Gibson
Michael Ellerman
Jon Loeliger
Johannes Berg
Christian Krafft
Vitaly Bordug
Grant Likely
Kumar Gala
Vitaly Wool
Benjamin Herrenschmidt
Nicolas DET
Li Yang
Kim Phillips
Mark A. Greer
Zang Roy-r61911
Anton Blanchard
Kumar Gala
Arnd Bergmann
Paul Mackerras
Kumar Gala