110 lines
3.5 KiB
Plaintext
110 lines
3.5 KiB
Plaintext
|
|
* Samsung S2MPS11 Voltage and Current Regulator
|
|
|
|
The Samsung S2MP211 is a multi-function device which includes voltage and
|
|
current regulators, RTC, charger controller and other sub-blocks. It is
|
|
interfaced to the host controller using a I2C interface. Each sub-block is
|
|
addressed by the host system using different I2C slave address.
|
|
|
|
Required properties:
|
|
- compatible: Should be "samsung,s2mps11-pmic".
|
|
- reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
|
|
|
|
Optional properties:
|
|
- interrupt-parent: Specifies the phandle of the interrupt controller to which
|
|
the interrupts from s2mps11 are delivered to.
|
|
- interrupts: Interrupt specifiers for interrupt sources.
|
|
|
|
Optional nodes:
|
|
- clocks: s2mps11 provides three(AP/CP/BT) buffered 32.768 KHz outputs, so to
|
|
register these as clocks with common clock framework instantiate a sub-node
|
|
named "clocks". It uses the common clock binding documented in :
|
|
[Documentation/devicetree/bindings/clock/clock-bindings.txt]
|
|
- #clock-cells: should be 1.
|
|
|
|
- The following is the list of clocks generated by the controller. Each clock
|
|
is assigned an identifier and client nodes use this identifier to specify
|
|
the clock which they consume.
|
|
Clock ID
|
|
----------------------
|
|
32KhzAP 0
|
|
32KhzCP 1
|
|
32KhzBT 2
|
|
|
|
- regulators: The regulators of s2mps11 that have to be instantiated should be
|
|
included in a sub-node named 'regulators'. Regulator nodes included in this
|
|
sub-node should be of the format as listed below.
|
|
|
|
regulator_name {
|
|
[standard regulator constraints....];
|
|
};
|
|
|
|
regulator-ramp-delay for BUCKs = [6250/12500/25000(default)/50000] uV/us
|
|
|
|
BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explictly
|
|
regulator-ramp-delay = <0> can be used for them to disable ramp delay.
|
|
In absence of regulator-ramp-delay property, default ramp delay will be used.
|
|
|
|
NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set
|
|
for a particular group of BUCKs. So provide same regulator-ramp-delay<value>.
|
|
Grouping of BUCKs sharing ramp rate setting is as follow : BUCK[1, 6],
|
|
BUCK[3, 4], and BUCK[7, 8, 10]
|
|
|
|
The regulator constraints inside the regulator nodes use the standard regulator
|
|
bindings which are documented elsewhere.
|
|
|
|
The following are the names of the regulators that the s2mps11 pmic block
|
|
supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
|
|
as per the datasheet of s2mps11.
|
|
|
|
- LDOn
|
|
- valid values for n are 1 to 28
|
|
- Example: LDO0, LD01, LDO28
|
|
- BUCKn
|
|
- valid values for n are 1 to 9.
|
|
- Example: BUCK1, BUCK2, BUCK9
|
|
|
|
Example:
|
|
|
|
s2mps11_pmic@66 {
|
|
compatible = "samsung,s2mps11-pmic";
|
|
reg = <0x66>;
|
|
|
|
s2m_osc: clocks{
|
|
#clock-cells = 1;
|
|
clock-output-names = "xx", "yy", "zz";
|
|
};
|
|
|
|
regulators {
|
|
ldo1_reg: LDO1 {
|
|
regulator-name = "VDD_ABB_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
ldo2_reg: LDO2 {
|
|
regulator-name = "VDD_ALIVE_1.1V";
|
|
regulator-min-microvolt = <1100000>;
|
|
regulator-max-microvolt = <1100000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck1_reg: BUCK1 {
|
|
regulator-name = "vdd_mif";
|
|
regulator-min-microvolt = <950000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
buck2_reg: BUCK2 {
|
|
regulator-name = "vdd_arm";
|
|
regulator-min-microvolt = <950000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-ramp-delay = <50000>;
|
|
};
|
|
};
|
|
};
|