original_kernel/arch/powerpc/platforms/apus/Kconfig

131 lines
3.7 KiB
Plaintext

config AMIGA
bool
depends on APUS
default y
help
This option enables support for the Amiga series of computers.
config ZORRO
bool
depends on APUS
default y
help
This enables support for the Zorro bus in the Amiga. If you have
expansion cards in your Amiga that conform to the Amiga
AutoConfig(tm) specification, say Y, otherwise N. Note that even
expansion cards that do not fit in the Zorro slots but fit in e.g.
the CPU slot may fall in this category, so you have to say Y to let
Linux use these.
config ABSTRACT_CONSOLE
bool
depends on APUS
default y
config APUS_FAST_EXCEPT
bool
depends on APUS
default y
config AMIGA_PCMCIA
bool "Amiga 1200/600 PCMCIA support"
depends on APUS && EXPERIMENTAL
help
Include support in the kernel for pcmcia on Amiga 1200 and Amiga
600. If you intend to use pcmcia cards say Y; otherwise say N.
config AMIGA_BUILTIN_SERIAL
tristate "Amiga builtin serial support"
depends on APUS
help
If you want to use your Amiga's built-in serial port in Linux,
answer Y.
To compile this driver as a module, choose M here.
config GVPIOEXT
tristate "GVP IO-Extender support"
depends on APUS
help
If you want to use a GVP IO-Extender serial card in Linux, say Y.
Otherwise, say N.
config GVPIOEXT_LP
tristate "GVP IO-Extender parallel printer support"
depends on GVPIOEXT
help
Say Y to enable driving a printer from the parallel port on your
GVP IO-Extender card, N otherwise.
config GVPIOEXT_PLIP
tristate "GVP IO-Extender PLIP support"
depends on GVPIOEXT
help
Say Y to enable doing IP over the parallel port on your GVP
IO-Extender card, N otherwise.
config MULTIFACE_III_TTY
tristate "Multiface Card III serial support"
depends on APUS
help
If you want to use a Multiface III card's serial port in Linux,
answer Y.
To compile this driver as a module, choose M here.
config A2232
tristate "Commodore A2232 serial support (EXPERIMENTAL)"
depends on EXPERIMENTAL && APUS
---help---
This option supports the 2232 7-port serial card shipped with the
Amiga 2000 and other Zorro-bus machines, dating from 1989. At
a max of 19,200 bps, the ports are served by a 6551 ACIA UART chip
each, plus a 8520 CIA, and a master 6502 CPU and buffer as well. The
ports were connected with 8 pin DIN connectors on the card bracket,
for which 8 pin to DB25 adapters were supplied. The card also had
jumpers internally to toggle various pinning configurations.
This driver can be built as a module; but then "generic_serial"
will also be built as a module. This has to be loaded before
"ser_a2232". If you want to do this, answer M here.
config WHIPPET_SERIAL
tristate "Hisoft Whippet PCMCIA serial support"
depends on AMIGA_PCMCIA
help
HiSoft has a web page at <http://www.hisoft.co.uk/>, but there
is no listing for the Whippet in their Amiga section.
config APNE
tristate "PCMCIA NE2000 support"
depends on AMIGA_PCMCIA
help
If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise,
say N.
To compile this driver as a module, choose M here: the
module will be called apne.
config SERIAL_CONSOLE
bool "Support for serial port console"
depends on APUS && (AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y)
config HEARTBEAT
bool "Use power LED as a heartbeat"
depends on APUS
help
Use the power-on LED on your machine as a load meter. The exact
behavior is platform-dependent, but normally the flash frequency is
a hyperbolic function of the 5-minute load average.
config PROC_HARDWARE
bool "/proc/hardware support"
depends on APUS
source "drivers/zorro/Kconfig"
config PCI_PERMEDIA
bool "PCI for Permedia2"
depends on !4xx && !8xx && APUS