original_kernel/arch/arm/mach-ux500/board-mop500.h

92 lines
3.4 KiB
C

/*
* Copyright (C) ST-Ericsson SA 2010
*
* License terms: GNU General Public License (GPL) version 2
*/
#ifndef __BOARD_MOP500_H
#define __BOARD_MOP500_H
/* Snowball specific GPIO assignments, this board has no GPIO expander */
#define SNOWBALL_ACCEL_INT1_GPIO 163
#define SNOWBALL_ACCEL_INT2_GPIO 164
#define SNOWBALL_MAGNET_DRDY_GPIO 165
#define SNOWBALL_SDMMC_EN_GPIO 217
#define SNOWBALL_SDMMC_1V8_3V_GPIO 228
#define SNOWBALL_SDMMC_CD_GPIO 218
/* HREFv60-specific GPIO assignments, this board has no GPIO expander */
#define HREFV60_SDMMC_1V8_3V_GPIO 5
#define HREFV60_CAMERA_FLASH_ENABLE 21
#define HREFV60_MAGNET_DRDY_GPIO 32
#define HREFV60_DISP1_RST_GPIO 65
#define HREFV60_DISP2_RST_GPIO 66
#define HREFV60_ACCEL_INT1_GPIO 82
#define HREFV60_ACCEL_INT2_GPIO 83
#define HREFV60_SDMMC_CD_GPIO 95
#define HREFV60_XSHUTDOWN_SECONDARY_SENSOR 140
#define HREFV60_TOUCH_RST_GPIO 143
#define HREFV60_HAL_SW_GPIO 145
#define HREFV60_SDMMC_EN_GPIO 169
#define HREFV60_MMIO_XENON_CHARGE 170
#define HREFV60_PROX_SENSE_GPIO 217
/* MOP500 generic GPIOs */
#define CAMERA_FLASH_INT_PIN 7
#define CYPRESS_TOUCH_INT_PIN 84
#define XSHUTDOWN_PRIMARY_SENSOR 141
#define XSHUTDOWN_SECONDARY_SENSOR 142
#define CYPRESS_TOUCH_RST_GPIO 143
#define MOP500_HDMI_RST_GPIO 196
#define CYPRESS_SLAVE_SELECT_GPIO 216
/* GPIOs on the TC35892 expander */
#define MOP500_EGPIO(x) (NOMADIK_NR_GPIO + (x))
#define GPIO_MAGNET_DRDY MOP500_EGPIO(1)
#define GPIO_SDMMC_CD MOP500_EGPIO(3)
#define GPIO_CAMERA_FLASH_ENABLE MOP500_EGPIO(4)
#define GPIO_MMIO_XENON_CHARGE MOP500_EGPIO(5)
#define GPIO_PROX_SENSOR MOP500_EGPIO(7)
#define GPIO_HAL_SENSOR MOP500_EGPIO(8)
#define GPIO_ACCEL_INT1 MOP500_EGPIO(10)
#define GPIO_ACCEL_INT2 MOP500_EGPIO(11)
#define GPIO_BU21013_CS MOP500_EGPIO(13)
#define MOP500_DISP2_RST_GPIO MOP500_EGPIO(14)
#define MOP500_DISP1_RST_GPIO MOP500_EGPIO(15)
#define GPIO_SDMMC_EN MOP500_EGPIO(17)
#define GPIO_SDMMC_1V8_3V_SEL MOP500_EGPIO(18)
#define MOP500_EGPIO_END MOP500_EGPIO(24)
/*
* GPIOs on the AB8500 mixed-signals circuit
* Notice that we subtract 1 from the number passed into the macro, this is
* because the AB8500 GPIO pins are enumbered starting from 1, so the value in
* parens matches the GPIO pin number in the data sheet.
*/
#define MOP500_AB8500_GPIO(x) (MOP500_EGPIO_END + (x) - 1)
/*Snowball AB8500 GPIO */
#define SNOWBALL_VSMPS2_1V8_GPIO MOP500_AB8500_PIN_GPIO(1) /* SYSCLKREQ2/GPIO1 */
#define SNOWBALL_PM_GPIO1_GPIO MOP500_AB8500_PIN_GPIO(2) /* SYSCLKREQ3/GPIO2 */
#define SNOWBALL_WLAN_CLK_REQ_GPIO MOP500_AB8500_PIN_GPIO(3) /* SYSCLKREQ4/GPIO3 */
#define SNOWBALL_PM_GPIO4_GPIO MOP500_AB8500_PIN_GPIO(4) /* SYSCLKREQ6/GPIO4 */
#define SNOWBALL_EN_3V6_GPIO MOP500_AB8500_PIN_GPIO(16) /* PWMOUT3/GPIO16 */
#define SNOWBALL_PME_ETH_GPIO MOP500_AB8500_PIN_GPIO(24) /* SYSCLKREQ7/GPIO24 */
#define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* GPIO26 */
struct i2c_board_info;
extern void mop500_sdi_init(struct device *parent);
extern void snowball_sdi_init(struct device *parent);
extern void hrefv60_sdi_init(struct device *parent);
extern void mop500_sdi_tc35892_init(struct device *parent);
void __init mop500_u8500uib_init(void);
void __init mop500_stuib_init(void);
void __init mop500_pins_init(void);
void __init hrefv60_pins_init(void);
void __init snowball_pins_init(void);
void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
unsigned n);
#endif