If a write error occurs, the affected block is placed on the
bad_used_list. In the case that the write error occured
when writing summary data the block was also being placed on
the dirty_list, which caused list corruption and ultimately
a soft lockup in jffs2_mark_node_obsolete. This fixes that.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
A new module parameter has been added called 'overridesize',
which overrides the size that would be determined by the
ID bytes. 'overridesize' is specified in erase blocks and
as the exponent of a power of two e.g. 5 means a size of
32 erase blocks.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
A new module parameter 'rptwear' specifies how many erases between
reporting wear information. Zero means never.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
New module parameters have been added to nandsim to
simulate:
bitflips random bit flips
badblocks blocks that are initially marked bad
weakblocks blocks that fail to erase after a
small number of erase cycles
weakpages pages that fail to write after a
small number of successful writes
gravepages pages that fail to read after a
small number of successful reads
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Enhance nandsim to be able to create more than 1 partition.
A new module parameter 'parts' may be used to specify partition
sizes.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When the MTD driver returns write failure, the following deadlock
occurs:
We are in __jffs2_flush_wbuf(), we hold &c->wbuf_sem. Write failure.
jffs2_wbuf_recover()->jffs2_reserve_space_gc()->jffs2_do_reserve_space()
->jffs2_erase_pending_blocks()->jffs2_flash_read()
and it tries to lock &c->wbuf_sem again. Deadlock.
Reported-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is a slight bug in nand_default_block_markbad, where the offset is
cast to an integer, prior to being shifted. This means that on large
offsets, it is incorrectly doing a signed shift & losing bits. Fixed
this by doing the cast after the shift (as is done elsewhere in the code).
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for AT26Fxxx dataflash devices. These devices have a quite different
commandset than the AT45xxx chips, which are handled by at91_dataflash.c, so a
combined driver turned out to be more ugly than useful.
Tested only on AT26F004.
Signed-off-by: Hans-Jürgen Koch <hjk@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The ops.len member is not initialized, because it is unused for this
operation. The length check needs to use ops.ooblen instead
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The support for obsolete ancient NAND chips adds .data size and one
of the old ids conflicts with a modern one. Make the support for
such chips depending on a config option.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use the functions in the ecc structure instead of the default ones,
so the override by the board driver is effective also for software ecc
code paths.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Check the node CRC on scan before doing anything else with the node.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
o A dependency on the processor architecture does not make sense;
delete it.
o The Alchemy and MTX drivers requires MTD_PARTITIONS and MTD_CFI to work,
make those dependencies.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Auto unlock sectors on resume for auto locking flash on power up.
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Delete everything related to the apparently non-existent kernel config
option JFFS2_PROC.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add flash and rootfs mappings for the PMC-Sierra MSP71xx devices.
This patch references some platform support files previously submitted to
the linux-mips@linux-mips.org list.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Delete the unreferenced header file include/linux/mtd/iflash.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Delete the obsolete source file fs/jffs2/comprtest.c.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (23 commits)
USB Elan FTDI: check for workqueue creation
USB: fix spinlock recursion in cdc-acm.c
USB: fix Unaligned access in EHCI driver
USB: Product ID for FT232RL in ftdi_sio
USBNET: DM9501: Add Corega FEther USB-TXC support.
USB: ipaq.c: Additional devices
USB: further fix for usb-serial
USB: fix usb-serial device naming bug
USB: RTS/DTR signal patch for airprime driver
USB: ftdi_sio: use port_probe / port_remove thereby fixing access to the latency_timer
usb-serial: fix shutdown / device_unregister order
USB: add Additional PIDs in ftdi_sio
USB: add QL355P power supply ids to fdti_sio
USB: New device IDs for cp2101 driver
USB: kill dead code from hub.c
USB: ratelimit debounce error messages
USB: pxa2xx_udc: fix hardcoded irq number
UHCI: fix port resume problem
USB: set the correct interval for interrupt URBs
USB: goku_udc: Remove crude cache coherency code
...
Delay the read of the EC status register until
after the event that caused it occurs -- otherwise
it is possible to read and act on stale status that was
associated with the previous event.
Do this with a perpetually incrementing "event_count" to detect
when a new event occurs and it is safe to read status.
There is no workaround for polling mode -- it is inherently
exposed to reading and acting on stale status, since it
doesn't have an interrupt to tell it the event completed.
http://bugzilla.kernel.org/show_bug.cgi?id=8110
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
this fixes the spinlock recursion issue. The older fix was incomplete.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I get following warnings on spar64:
Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd]
Despite of the comment in the patched code, the type cast used there
does make unaligned access. The fix was made as it's done in
ohci-hub.c.
Signed-off-by: Max Dmitrichenko <dmitrmax@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.
From: Gard Spreemann <spreeman@stud.ntnu.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter:
> Hi Greg
>
> 34ef50e5b1 is definitely
> the source of the problem. Reverting that makes the
> ftdi port show up as ttyUSB0 again for me and it
> can actually be opened.
This patch should fix the issue.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Craig Schlenter <craig@codefountain.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:
Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem. Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.
With the attached patch, the RTS/DTR lines are resetted on a close. The
code was mainly taken from the option.c driver.
Convert all the port specific code in attach / shutdown to use the new
port_probe / port_register callbacks from device_register /
device_unregister allowing adding the sysfs attributes to be added at
the correct time and to the serial port device itself, instead of to
the unadorned usb device, avoiding a NULL dereference.
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ensure that the ->port_remove() callbacks get called before the
->shutdown() callback which makeing the order symmetric with
->attach() being called before ->port_probe().
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've developed some devices with FTDI chips (FT232xx). FTDI was so kind
to give some own PID's which I can use together with their VID. Some of
the devices are already very popular here and I have customers from
universities, institutes .....
I use the FTDI VID 0x0403. My PID's are:
0xff38 - IBS US485 (USB<-->RS422/485 interface)
0xff39 - IBS PIC-Programmer
0xff3a - IBS Card reader for PCMCIA SRAM-cards
0xff3b - IBS PK1 - Particel counter
0xff3c - IBS RS232 - Monitor
0xff3d - APP 70 (dust monitoring system)
0xff3e - IBS PEDO-Modem (RF modem 868.35 MHz)
0xff3f - future device
The company is "IBS Ing.-Buero Schleusener".
From: Thomas Schleusener <thomas@be-schl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adrian Hunter
Artem Bityutskiy
Andre Renaud
Hans-Jürgen Koch
Thomas Gleixner
Thomas Gleixner
Thomas Gleixner
sshahrom@micron.com
Ralf Baechle
Rodolfo Giometti
Robert P. J. Day
Marc St-Jean
David Woodhouse
Linus Torvalds
Len Brown
Alexey Starikovskiy
Cyrill Gorcunov
Oliver Neukum
Max Dmitrichenko
Gard Spreemann
YOSHIFUJI Hideaki
Andre Spahlinger
Martin Schiller
Jim Radford
Thomas Schleusener