The classic MMC bus was defined as multi card bus
system, which is reflected in the design in the MMC
layer.
When SD showed up, the bus topology was abandoned
and a star topology (one card per host) was mandated.
MMC version 4 has followed this, officially deprecating
the bus topology.
As we do not have any known users of the bus
topology we can remove support for it. This will
simplify the code and rectify some incorrect
assumptions in the newer additions.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Suspending MMC/SD cards (versus removing and readding them) is an
inherently unsafe operation and has even been broken for some time.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure we don't deadlock when removing a suspended block
queue, something that might happen if the card is removed during
suspend.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure we kill of any pending detection runs when the host
is removed instead of when it is freed. Also add some debugging
to make sure the driver doesn't queue up more detection after it
has removed the host.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The mmc block queue functions are tailored for the mmc_block
driver, so move those functions into that module.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The "present" state indicates that the card is a registered device, so
it is more clear to put it together with the actual registration.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
All host drivers were #include:ing mmc/protocol.h just to
get access to the OCR bit defines. Move these to host.h instead.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for MMC 4.2 sector based cards. This tweaks the init a
bit and reads a new field out of the EXT_CSD.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
sparc64:
drivers/misc/tifm_7xx1.c: In function `tifm_7xx1_probe':
drivers/misc/tifm_7xx1.c:294: error: `DMA_32BIT_MASK' undeclared
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It was found that delays associated with issue and completion of the commands
severely limit performance of the new, fast SD cards. To alleviate this issue
scatter-gather emulation in software is implemented for both dma and pio
transfer modes. Non-block aligned and high memory sg entries are accounted
for.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Resume should not explicitly check for media type. Instead, it may relay
on success of socket initialization.
Small changes are introduced to tifm_sd_initialize to make it more robust.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
State machine used to to track mmc command state was found to be fragile
and unreliable, making many cards unusable. The safer solution is to perform
all needed checks at every card event.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
To allow for switching of trasfer mode (dma/pio) on a per-request basis,
pio and dma request issue and completion function are now merged.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
host->flags variable was hosting a collection of bits with different
semantics. For clarity, hardware bit masks are now defined as macros,
socket flags represented as bit fields and flags (now cmd_flags) only
hosts command processing modifiers.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This wait was needed because of the mmc layer failure to wait for completion
of all outstanding commands before host removal. It should be fixed now in
the mmc layer.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
tifm_sd_terminate can only lawfully be called on device removal so it can be
merged with tifm_sd_remove.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fixes to the adapter resume function to correctly handle all possible cases:
1. Card is removed during suspend
2. Card is inserted during suspend into previously empty socket
3. Card is replaced during suspend by same or different media type card.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some details of the device management (create, add, remove) are really
belong to the tifm_core, as they are not hardware specific.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some details of the adapter management (create, add, remove) are really
belong to the tifm_core, as they are not hardware specific.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Remove unneeded conditions and change a sleeping regime a little in the
card type detection routine.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Freezeable workqueue makes sure that adapter work items (device insertions
and removals) would be handled after the system is fully resumed. Previously
this was achieved by explicit freezing of the kthread.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Remove code duplicating the kernel functionality and clean up data
structures involved in driver matching.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Instead of passing transformed value of adapter interrupt status to
socket drivers, implement two separate callbacks - one for card events
and another for dma events.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Block completion interrupts occur faster than we can process
them, so just ignore them competely.
Commit also fixes up some incorrect register defines.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Now that we've fixed our only offender when it comes to strange sg
list, add a check so that future users keep the sg list proper with
regard to transfer size.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
mmc layer may introduce additional (compared to block layer) limits on
request size. Culling of the sg list to match adjusted request size
simplifies the handling of such cases in the low level driver, allowing
it to skip block count checks while processing sg entries.
(fixes for wbsd and sdhci by Pierre Ossman)
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The Marvell IDE interface on my machine would hit a BUG_ON() in
lib/iomem.c because it was calling ata_pci_init_one() specifying just a
single port on the host, but that would actually end up trying to
initialize two ports, the second one with bogus information.
This fixes "ata_pci_init_one()" so that it actually passes down the
n_ports variable that it got from the low-level driver to the host
allocation routine ("ata_host_alloc_pinfo()"), which results in the ATA
layer actually having the correct port number information.
And in order to make it all work, I also needed to fix a few places that
had incorrectly hard-coded the fact that a host always had exactly two
ports (both ata_pci_init_bmdma() and ata_request_legacy_irqs() would
just always iterate over both ports).
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For backwards compatibility, call_platform_enable_wakeup() can return 0
instead of -EIO since we aren't guaranteed to have errno defined.
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a kvasprintf() function to complement kasprintf().
No in-tree users yet, but I have some coming up.
[akpm@linux-foundation.org: EXPORT it]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Keir Fraser <keir@xensource.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the docs and behaviour from "all states valid" to "no
states valid" if no .valid callback is assigned. Users of pm_ops that only
need mem sleep can assign pm_valid_only_mem without any overhead, others
will require more elaborate callbacks.
Now that all users of pm_ops have a .valid callback this is a safe thing to
do and prevents things from getting messy again as they were before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Looks-okay-to: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).
This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: linux-pm@lists.linux-foundation.org
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the firmware disk suspend mode which is the wrong approach,
it is supposed to be used for implementing firmware-based disk suspend but
cannot actually be used for that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're getting lockdep warnings due to a post-2.6.21-rc7 bugfix.
The xattr_sem can never be taken in the manner described. Internal inodes
are protected by I_PRIVATE. Add the appropriate annotation.
Cc: <stable@kernel.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's print_symbol function dumps a kernel symbol with printk. This
patch extends the functionality of kallsyms.c so that the symbol lookup
function may be used without the printk. This is useful for modules that
want to dump symbols elsewhere, for example, to debugfs. I intend to use
the new function call in the GFS2 file system (which will be a separate
patch).
[akpm@linux-foundation.org: build fix]
[clameter@sgi.com: sprint_symbol should return length of string like sprintf]
Signed-off-by: Robert Peterson <rpeterso@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Paulo Marques <pmarques@grupopie.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When allocating local ports, do not allow a bind to a port
with a specific local address when a bind to that port with
a wildcard local address already exists.
Noticed by Linus.
Signed-off-by: David S. Miller <davem@davemloft.net>
I accidently applied an earlier version of Eric Dumazet's patch, from
March 21st. His version from March 30th didn't have these bugs, so
this just interdiffs to the correct patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (56 commits)
ieee1394: remove garbage from Kconfig
ieee1394: more help in Kconfig
ieee1394: ohci1394: Fix mistake in printk message.
ieee1394: ohci1394: remove unnecessary rcvPhyPkt bit flipping in LinkControl register
ieee1394: ohci1394: fix cosmetic problem in error logging
ieee1394: eth1394: send async streams at S100 on 1394b buses
ieee1394: eth1394: fix error path in module_init
ieee1394: eth1394: correct return codes in hard_start_xmit
ieee1394: eth1394: hard_start_xmit is called in atomic context
ieee1394: eth1394: some conditions are unlikely
ieee1394: eth1394: clean up fragment_overlap
ieee1394: eth1394: don't use alloc_etherdev
ieee1394: eth1394: omit useless set_mac_address callback
ieee1394: eth1394: CONFIG_INET is always defined
ieee1394: eth1394: allow MTU bigger than 1500
ieee1394: unexport highlevel_host_reset
ieee1394: eth1394: contain host reset
ieee1394: eth1394: shorter error messages
ieee1394: eth1394: correct a memset argument
ieee1394: eth1394: refactor .probe and .update
...
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
USB HID: don't warn on idVendor == 0
USB HID: add 'quirks' module parameter
USB HID: add support for dynamically-created quirks
USB HID: clarify static quirk handling as squirks
USB HID: encapsulate quirk handling into hid-quirks.c
USB HID: EMS USBII device needs HID_QUIRK_MULTI_INPUT
HID: update copyright and authorship macro
HID: introduce proper zeroing of unused bits in output reports
USB HID: add support for WiseGroup MP-8800 Quad Joypad
USB HID: add FF support for Logitech Force 3D Pro Joystick
USB HID: numlock quirk for dell W7658 keyboard
USB HID: Logitech MX3000 keyboard needs report descriptor quirk
USB HID: extend quirk for Logitech S510 keyboard
USB HID: usbkbd/usbmouse - handle errors when registering devices
USB HID: add QUIRK_HIDDEV for Belkin Flip KVM
HID: enable dead keys on a belkin wireless keyboard
USB HID: Thustmaster firestorm dual power v1 support
USB HID: specify explicit size for hid_blacklist.quirks
USB HID: fix retry & reset logic
USB HID: consolidate vendor/product ids
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[IPV4] SNMP: Support OutMcastPkts and OutBcastPkts
[IPV4] SNMP: Support InMcastPkts and InBcastPkts
[IPV4] SNMP: Support InTruncatedPkts
[IPV4] SNMP: Support InNoRoutes
[SNMP]: Add definitions for {In,Out}BcastPkts
[TCP] FRTO: RFC4138 allows Nagle override when new data must be sent
[TCP] FRTO: Delay skb available check until it's mandatory
[XFRM]: Restrict upper layer information by bundle.
[TCP]: Catch skb with S+L bugs earlier
[PATCH] INET : IPV4 UDP lookups converted to a 2 pass algo
[L2TP]: Add the ability to autoload a pppox protocol module.
[SKB]: Introduce skb_queue_walk_safe()
[AF_IUCV/IUCV]: smp_call_function deadlock
[IPV6]: Fix slab corruption running ip6sic
[TCP]: Update references in two old comments
[XFRM]: Export SPD info
[IPV6]: Track device renames in snmp6.
[SCTP]: Fix sctp_getsockopt_local_addrs_old() to use local storage.
[NET]: Remove NETIF_F_INTERNAL_STATS, default to internal stats.
[NETPOLL]: Remove CONFIG_NETPOLL_RX
...
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
[PATCH] elevator: elv_list_lock does not need irq disabling
[BLOCK] Don't pin lots of memory in mempools
cfq-iosched: speedup cic rb lookup
ll_rw_blk: add io_context private pointer
cfq-iosched: get rid of cfqq hash
cfq-iosched: tighten queue request overlap condition
cfq-iosched: improve sync vs async workloads
cfq-iosched: never allow an async queue idling
cfq-iosched: get rid of ->dispatch_slice
cfq-iosched: don't pass unused preemption variable around
cfq-iosched: get rid of ->cur_rr and ->cfq_list
cfq-iosched: slice offset should take ioprio into account
[PATCH] cfq-iosched: style cleanups and comments
cfq-iosched: sort IDLE queues into the rbtree
cfq-iosched: sort RT queues into the rbtree
[PATCH] cfq-iosched: speed up rbtree handling
cfq-iosched: rework the whole round-robin list concept
cfq-iosched: minor updates
cfq-iosched: development update
cfq-iosched: improve preemption for cooperating tasks
A transmitted IP multicast datagram should be counted as OutMcastPkts.
By the same token, a transmitted IP broadcast datagram should be
counted as OutBcastPkts.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pierre Ossman
Andrew Morton
Alex Dubov
Linus Torvalds
David Rientjes
Jeremy Fitzhardinge
Johannes Berg
Jeff Mahoney
Robert Peterson
David S. Miller
Mitsuru Chinen