Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the default config file for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The FSL PCI code depends on PCI quirks being enabled to function
properly. We can ensure this by doing a select in Kconfig of
PCI_QUIRKS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Instead of rounding the divider down, improve the baud-rate generators
accuracy by rounding to the nearest integer.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On booke processors, the code that maps low memory only uses up to three
CAM entries, even though there are sixteen and nothing else uses them.
Make this number configurable in the advanced options menu along with max
low memory size. If one wants 1 GB of lowmem, then it's typically
necessary to have four CAM entries.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code that maps kernel low memory would only use page sizes up to 256
MB. On E500v2 pages up to 4 GB are supported.
However, a page must be aligned to a multiple of the page's size. I.e.
256 MB pages must aligned to a 256 MB boundary. This was enforced by a
requirement that the physical and virtual addresses of the start of lowmem
be aligned to 256 MB. Clearly requiring 1GB or 4GB alignment to allow
pages of that size isn't acceptable.
To solve this, I simply have adjust_total_lowmem() take alignment into
account when it decides what size pages to use. Give it PAGE_OFFSET =
0x7000_0000, PHYSICAL_START = 0x3000_0000, and 2GB of RAM, and it will map
pages like this:
PA 0x3000_0000 VA 0x7000_0000 Size 256 MB
PA 0x4000_0000 VA 0x8000_0000 Size 1 GB
PA 0x8000_0000 VA 0xC000_0000 Size 256 MB
PA 0x9000_0000 VA 0xD000_0000 Size 256 MB
PA 0xA000_0000 VA 0xE000_0000 Size 256 MB
Because the lowmem mapping code now takes alignment into account,
PHYSICAL_ALIGN can be lowered from 256 MB to 64 MB. Even lower might be
possible. The lowmem code will work down to 4 kB but it's possible some of
the boot code will fail before then. Poor alignment will force small pages
to be used, which combined with the limited number of TLB1 pages available,
will result in very little memory getting mapped. So alignments less than
64 MB probably aren't very useful anyway.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code to map lowmem uses three CAM aka TLB[1] entries to cover it. The
size of each is stored in three globals named __cam0, __cam1, and __cam2.
All the code that uses them is duplicated three times for each of the three
variables.
We have these things called arrays and loops....
Once converted to use an array, it will be easier to make the number of
CAMs configurable.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We currently have a few variants of fsl-booke processors (e500v1, e500v2,
e500mc, and e200). They all have minor differences that we had previously
been handling via ifdefs.
To move towards having this support the following changes have been made:
* PID1, PID2 only exist on e500v1 & e500v2 and should not be accessed on
e500mc or e200. We use MMUCFG[NPIDS] to determine which case we are
since we only touch PID1/2 in extremely early init code.
* Not all IVORs exist on all the processors so introduce cpu_setup
functions for each variant to setup the proper IVORs that are either
unique or exist but have some variations between the processors
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pcie nodes to the appropriate dts files, plus adds
some probing code for the boards.
Also, remove of_device_is_avaliable() check from the mpc837x_mds.c
board file, as mpc83xx_add_bridge() has the same check now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for PCI-Express controllers as found on the
newer MPC83xx chips.
The work is loosely based on the Tony Li's patch[1], but unlike the
original patch, this patch implements sliding window for the Type 1
transactions using outbound window translations, so we don't have to
ioremap the whole PCI-E configuration space.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-January/049028.html
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
powerpc/pseries: Correct VIO bus accounting problem in CMO env.
powerpc: More printing warning fixes for the l64 to ll64 conversion
powerpc: Remove arch/ppc cruft from Kconfig
powerpc: Printing fix for l64 to ll64 conversion: phyp_dump.c
powerpc/embedded6xx: Update defconfigs
powerpc/8xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/mpc8313erdb: fix kernel panic because mdio device is not probed
powerpc/4xx: Update multi-board PowerPC 4xx defconfigs
powerpc/44x: Update PowerPC 44x defconfigs
powerpc/40x: Update PowerPC 40x defconfigs
powerpc/85xx: Fix typo in mpc8572ds dts
powerpc/44x: Warp patches for the new NDFC driver
powerpc/4xx: DTS: Add Add'l SDRAM0 Compatible and Interrupt Info
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 5329 ColdFire periphal addressing
uclinux: add process name to allocation error message
m68knommu: correct the mii calculations for 532x ColdFire FEC
m68knommu: add ColdFire M532x to the FEC configuration options
m68knommu: fix syscall restarting
m68knommu: remove the obsolete and long unused comempci chip support
m68knommu: remove the no longer used PCI support option
m68knommu: remove obsolete and unused eLIA board
m68knommu: set NO_DMA
m68knommu: fix cache flushing for the 527x ColdFire processors
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
m68knommu: use one exist from execption
Commit d7b1956fed ("DMI: Introduce
dmi_first_match to make the interface more flexible") introduced compile
errors like the following when !CONFIG_DMI
drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast
We just need a dummy version of dmi_first_match() to fix this all up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Schedule a vblank signal, kill the process, and we'll go walking over freed
memory. Given that no open-source userland exists using this, nor have I
ever heard of a consumer, just let this code die.
Signed-off-by: Eric Anholt <eric@anholt.net>
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.
This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE. Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE. Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system. Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.
Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should. Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove some leftover cruft from the arch/ppc days
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Given just how hard it is to find the code that uses MAY_APPEND
it's probably not a big surprise that this went unnoticed for so
long. The Smack rules loading code is incorrectly setting the
MAY_READ bit when MAY_APPEND is requested.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
USB: Driver for Freescale QUICC Engine USB Host Controller
USB: option: add QUANTA HSDPA Data Card device ids
USB: storage: Add another unusual_dev for off-by-one bug
USB: unusual_dev: usb-storage needs to ignore a device
USB: GADGET: fix !x & y
USB: new id for ti_usb_3410_5052 driver
USB: cdc-acm: Add another conexant modem to the quirks
USB: 'option' driver - onda device MT503HS has wrong id
USB: Remove ZTE modem from unusual_devices
USB: storage: support of Dane-Elec MediaTouch USB device
USB: usbmon: Implement compat_ioctl
USB: add kernel-doc for wusb_dev in struct usb_device
USB: ftdi_sio driver support of bar code scanner from Diebold
USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
USB: cp2101 device
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
USB: remove vernier labpro from ldusb
USB: CDC-ACM quirk for MTK GPS
USB: cdc-acm: support some gps data loggers
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
...
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.
Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.
At this time usb_modeswitch does not work with this device.
Reported-by: The Solutor <thesolutor@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
! has a higher precedence than &
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another Conexant, another device with the same quirk
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).
This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: Marcel Sebek <sebek64@post.cz>
Acked-by: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.
Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.
Signed-off-by: Jean-Baptiste Onofre <jb@nanthrax.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0
It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.
This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported by Randy Dunlap from a warning on the v2.6.29 merge window.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: Mhayk Whandson <eu@mhayk.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: Robie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,
PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c
From: Tomasz K <eros81@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?
output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):
before patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)
after patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0
Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Labpro device is in both ldusb and vstusb device tables.
Should only be a vstusb device.
Signed-off-by: stephen ware <stephen.ware@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.
I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: Andrew Lunn, <andrew@lunn.ch>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.
From: James A. Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.
This patch fixes this issue.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies. This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initializes the actual_len field to 0 before every DMA transaction.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:
drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Martyn Welch
Kumar Gala
Reynes Philippe
Peter Korsgaard
Laurent Pinchart
Trent Piepho
Anton Vorontsov
Linus Torvalds
Eric Anholt
Gerhard Pircher
Robert Jennings
Stephen Rothwell
Josh Boyer
Benjamin Herrenschmidt
Casey Schaufler
Alex.Cheng@quantatw.com
Phil Dibowitz
Roel Kluin
Oliver Neukum
Alan Cox
Marcel Sebek
Jean-Baptiste Onofre
Pete Zaitcev
Inaky Perez-Gonzalez
Mhayk Whandson
Robie Basak
Tomasz K
Brandon Philips
sware
Andrew Lunn
James A. Treacy
Bryan Wu
David Brownell
Swaminathan S
Hugo Villeneuve